A decohesion pathway for hydrogen embrittlement in nickel: Mechanism and quantitative prediction

Related publications (27)

About
Privacy
Disclaimer

Graph Chatbot

Modeling friction and wear using an adaptive discrete-continuum coupling

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

Controlling crystal cleavage in focused ion beam shaped specimens for surface spectroscopy

Philip Johannes Walter Moll, Matthias Carsten Putzke, Andrew Scott Hunter

Our understanding of quantum materials is commonly based on precise determinations of their electronic spectrum by spectroscopic means, most notably angle-resolved photoemission spectroscopy (ARPES) and scanning tunneling microscopy. Both require atomicall ...

Aip Publishing2024

Tension-tension fatigue behavior of basalt composite hybrid joints

Thomas Keller, Lulu Liu, Xin Wang

The tension–tension fatigue behavior of pseudo-ductile hybrid bonded-bolted double lap basalt composite joints, composed of pseudo-ductile adhesives and adherends with multi-directional fiber architecture, was experimentally investigated. The fatigue damag ...

2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Tara Habibi, Landolf-Giosef-Anastasios Rhode-Barbarigos

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Strain engineering and strain measurement by spring tethers on suspended epitaxial GaN-on-Si photonic crystal devices

Romuald Houdré, Jun Wang

Suspended epitaxial gallium nitride (GaN) on silicon (Si) photonic crystal devices suffer from large residual tensile strain, especially for long waveguides, because fine structures tend to crack due to large stress. By introducing spring-like tethers, des ...

Iop Publishing Ltd2024

Proposed residual stress model for hot‐rolled wide flange steel cross sections

Dimitrios Lignos, Albano António De Abreu E Presa De Castro E Sousa, Andronikos Skiadopoulos

Residual stresses in hot-rolled wide flange steel cross sections may lead to premature yielding, accelerated corrosion and brittle fracture of steel members. The above phenomena lead to a loss of a steel member's stiffness and resistance under mechanical l ...

Ernst & Sohn2023

Three-dimensional buoyant hydraulic fractures: finite volume release

Brice Tanguy Alphonse Lecampion, Andreas Möri

In impermeable media, a hydraulic fracture can continue to expand even without additional fluid injection if its volume exceeds the limiting volume of a hydrostatically loaded radial fracture. This limit depends on the mechanical properties of the surround ...

Cambridge University Press2023

Using video detection of snow surface movements to estimate weak layer crack propagation speeds

Johan Alexandre Philippe Gaume, Bertil Trottet, Alec van Herwijnen

Dry-snow slab avalanches release due to crack propagation in a weak snow layer under a cohesive snow slab. Crack propagation speeds can provide insights into the potential size of avalanches and inform fracture and avalanche release models. Despite their i ...

CAMBRIDGE UNIV PRESS2023

Mode I and Mode II fracture behavior in pultruded glass fiber-polymer - Experimental and numerical investigation

Thomas Keller

Many recent works have shown that the capacity of pultruded glass fiber-polymer structural members is governed by interlaminar failure. However, there is still a lack of information regarding the fracture properties associated and the best techniques to be ...

Elsevier Sci Ltd2023

Three-dimensional hydraulic fracture propagation in homogeneous and heterogeneous media

Carlo Peruzzo

Hydraulic fractures are tensile fractures that occur in solid materials due to the natural intrusion or anthropogenic injection of a viscous fluid into a fracture channel. The deliberate creation of hydraulic fractures is part of an industrial technology h ...

EPFL2023

Page 2 of 3