Concept

Hardenability

Related publications (38)

Early cluster formation during rapid cooling of an Al-Cu-Mg alloy: In situ small-angle X-ray scattering

Jean-Marie Drezet, Helena Van Swygenhoven, Patrick Schloth

The formation of Cu-Mg clusters in an Al-Cu-Mg aluminum alloy is observed by small-angle X-ray scattering during cooling. Cooling rates are choosen to mimic the different conditions obtained at the surface and in the center of large forgings. Clusters of 0 ...

Elsevier2015

Photopolymerization device for minimally invasive implants: application to nucleus pulposus replacement

Dominique Pioletti, Pierre-Etienne Bourban, Andreas Schmocker, Azadeh Khoushabi

Photopolymerization is a common tool to harden materials initially in a liquid state. A surgeon can directly trigger the solidification of a dental implant or a bone or tissue filler. Traditionally, photopolymerization has been used mainly in dentistry. Ov ...

Springer2015

Quench-Induced Stresses in AA2618 Forgings for Impellers: A Multiphysics and Multiscale Problem

Jean-Marie Drezet, Nicolas Paul Henry Chobaut, Gilles Michel, Denis Carron

In the fabrication of heat-treatable aluminum parts such as AA2618 compressor impellers for turbochargers, solutionizing and quenching are key steps to obtain the required mechanical characteristics. Fast quenching is necessary to avoid coarse precipitatio ...

Springer2015

Measurements and modelling of residual stresses during quenching of thick heat treatable aluminium components in relation to their precipitation state

Nicolas Paul Henry Chobaut

In the fabrication of heat treatable aluminium parts, solutionising and quenching are key steps in order to obtain the required mechanical characteristics. Fast quenching is necessary to avoid coarse precipitation as this one reduces the mechanical propert ...

EPFL2015

Early precipitation during cooling of an Al-Zn-Mg-Cu alloy revealed by in situ small angle X-ray scattering

Jean-Marie Drezet, Helena Van Swygenhoven, Patrick Schloth

Early subnanometre cluster formation during quenching of a high-strength AA7449 aluminium alloy was investigated using in situ small angle X-ray scattering. Fast quench cooling was obtained by using a laser-based heating system. The size and number density ...

American Institute of Physics2014

On the influence of transgranular and intergranular failure mechanisms during dynamic loading of silicon nitride

Jean-François Molinari

Plane-strain tensile loading numerical simulations of dynamic crack propagation in silicon nitride microstructures are conducted. The strength and toughness are evaluated as a function of strain rate and microstructural parameters, including grain size and ...

Elsevier2014

Construction and test of a non-insulated insert coil using coated conductor tape

Pierluigi Bruzzone, Davide Uglietti, Rainer Wesche

A small coated conductor coil (central field 1 T at 200 A) was constructed and tested in order to evaluate the benefit and the possible disadvantages of non insulated, double pancake construction, in particular regarding quench protection. The insert coil ...

2014

Construction and test of a non-insulated insert coil using coated conductor tape

Pierluigi Bruzzone, Davide Uglietti, Rainer Wesche

Iop Publishing Ltd2014

Influence of quench rate and microstructure on bendability of AA6016 aluminum alloys

Andreas Mortensen, Andreas Rossoll, Frédéric Diologent, Jean-François Despois, Cyrille Bezençon

The influence of the quench rate after solution treatment on the bendability of AA6016 aluminum alloy sheets was investigated. Crack initiation during bending tests is found to be independent of quench rate whereas crack propagation is decreased after rapi ...

Elsevier2013

Analysis of hardening limits of oxide dispersion strengthened steel

Amuthan Ramar

Oxide dispersion strengthened (ODS) ferritic/martensitic (F/M) steels are promising materials for high temperature applications. The hardening limits from room temperature to 1000 degrees C of one of such steel, ODS EUROFER97, together with the impact of t ...

Elsevier Science Bv2013

Graph Chatbot

Chat with Graph Search

Ask any question about EPFL courses, lectures, exercises, research, news, etc. or try the example questions below.

DISCLAIMER: The Graph Chatbot is not programmed to provide explicit or categorical answers to your questions. Rather, it transforms your questions into API requests that are distributed across the various IT services officially administered by EPFL. Its purpose is solely to collect and recommend relevant references to content that you can explore to help you answer your questions.