MSE-637(a): Transmission electron microscopy and diffraction (a)

Summary

This intensive course is intended for researchers who envisage using transmission electron microscopy to study materials samples or to help them interpret TEM data in publications. It presents basics of TEM instrumentation, imaging, electron diffraction, specimen preparation and high-resolution TEM.

Official source

https://edu.epfl.ch/coursebook/en/transmission-electron-microscopy-and-diffraction-a-MSE-637-A

Moodle Page

http://go.epfl.ch/MSE-637(a)

About this result

This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.

Instructors (2)

Related concepts (36)

Related courses (3)

Related MOOCs (9)

Marco Cantoni

1982-1988, Diploma course in Experimental Physics (certificate, 28.10.88)ETHZ Faculty IX MATHEMATICS and PHYSICS, Diploma Thesis: "Abweichungen von der ikosaedrischen Symmetrie in Al-Cu-Li Quasikristallen", Advisor: Prof. H.-U. Nissen 1989-1993, Ph.D. in Experimental Physics (certificate, 23.8.94) ETHZ Physics Department, Laboratory of Solid State Physics, Ph. D. Thesis No. 10421, Title: "Elektronenmikroskopische Untersuchung der Realkristallstruktur epitaktischer Schichten von Supraleitern des Typs SEBa2Cu3O7-x auf (100)-SrTiO3" Advisors: Prof. H.R. Ott, Prof. H. U. Nissen. 1994-1996,ETH Zürich,Material Science Department, Non-Metallic Materials, Prof. L. Gauckler: Microstructure characterisation of high-tech ceramic materials by means of SEM, TEM and atomic force microscopy: superconductor thick films (Bi-2212 on Ag) and solid oxide fuel cells (ZrO2, CeO2). 1996-1998, National Institute for Research in Inorganic Materials NIRIM, Japan Group for Special Research, Prof. S. Horiuchi: TEM of Bi-2223/Ag Tapes, Application of Imaging Plates (IP) in High Voltage TEM, Cryo-Lorentz-TEM of Superconducting Materials (Observation of Flux-Lines) 1998-2000, Ecole polytechnique fédéral de Lausanne, EPFL-CIME Centre interdépartemental de microscopie électronique CIME, Prof. P.A. Buffat: Projet 125, PPO II (programme prioritaire optique): Characterization of materials and devices for optic and optoelectronic applications by electron microscopy. 2001-2003, Ecole polytechnique fédéral de Lausanne, EPFL STI IMX LCCeramics Laboratory, Prof. Nava Setter Characterisation of ferroelectric materials, transmission electron microscopy of relaxor ferroelectric materials 2004, University of Geneva, Physics Department, Condensed matter Physics Group of Prof. R. Flükiger, TEM of Multifilament Nb3Sn superconducting wires, in collaboration with EPFL-CIME Since 1.11.04, EPFL-SB-CIME

Emadeddin Oveisi

Dr Emad Oveisi is a senior scientist at the Interdisciplinary Centre for Electron Microscopy (CIME), EPFL. Emad received a BSc in Metallurgy and Materials Engineering (2005) and an MSc in Materials Science (2008) both from the University of Tehran (Iran). He graduated with a PhD in Materials Science and Engineering at EPFL in 2014 for a thesis on the "Three-Dimensional STEM Imaging of Dislocations" under the direction of Prof. Cécile Hébert. The PhD thesis at the Electron Spectrometry and Microscopy Laboratory (LSME), served as an introduction to many of the advanced microscopy techniques that have proven to be a platform for his research career. A post-doctoral research at the centre for electron microscopy gave him the opportunity to peruse a cutting-edge research on one of the most modern aberration-corrected transmission electron microscopes.Since the inauguration of the Energypolis campus of EPFL in Sion, he has been the manager and reference scientist of the electron microscopy platform of EPFL-Valais, working with 9 research groups and more than 200 researchers. In addition to this core responsibility, he provides advanced microscopy consulting and service to EPFL scientists and assist their research to the highest level possible. Emad Oveisi’s research focuses on the application and development of novel electron microscopy techniques, with emphasis on 3D imaging of crystal defects, as well as the precision measurement of materials properties using aberration-corrected S/TEM. In 2018, he received the prestigious Microscopy Innovation Award for inventing “Single-shot three-dimensional electron imaging”, a novel technique that enables 3D imaging of in situ dynamics. In 2016 Emad was elected as an interim representative for the scientific staff ("corps intermédiaire") to the Council of the Institute of Chemistry (ISIC). Since 2019, he is a member of EPFL Teachers’ Council (CCE) and has been elected as one of its four bureau members. This role allows him to be exposed to new ideas and pedagogical challenges, as well being involved in discussions with the Vice Presidency of Education (VPE) and other teaching organisations for defining teaching strategies at the EPFL.

Transmission electron microscopy

Transmission electron microscopy (TEM) is a microscopy technique in which a beam of electrons is transmitted through a specimen to form an image. The specimen is most often an ultrathin section less than 100 nm thick or a suspension on a grid. An image is formed from the interaction of the electrons with the sample as the beam is transmitted through the specimen. The image is then magnified and focused onto an imaging device, such as a fluorescent screen, a layer of photographic film, or a sensor such as a scintillator attached to a charge-coupled device.

Scanning transmission electron microscopy

A scanning transmission electron microscope (STEM) is a type of transmission electron microscope (TEM). Pronunciation is [stɛm] or [ɛsti:i:ɛm]. As with a conventional transmission electron microscope (CTEM), images are formed by electrons passing through a sufficiently thin specimen. However, unlike CTEM, in STEM the electron beam is focused to a fine spot (with the typical spot size 0.05 – 0.2 nm) which is then scanned over the sample in a raster illumination system constructed so that the sample is illuminated at each point with the beam parallel to the optical axis.

Electron microscope

An electron microscope is a microscope that uses a beam of electrons as a source of illumination. They use electron optics that are analogous to the glass lenses of an optical light microscope. As the wavelength of an electron can be up to 100,000 times shorter than that of visible light, electron microscopes have a higher resolution of about 0.1 nm, which compares to about 200 nm for light microscopes.

Electron energy loss spectroscopy

Electron energy loss spectroscopy (EELS) is a form of electron microscopy in which a material is exposed to a beam of electrons with a known, narrow range of kinetic energies. Some of the electrons will undergo inelastic scattering, which means that they lose energy and have their paths slightly and randomly deflected. The amount of energy loss can be measured via an electron spectrometer and interpreted in terms of what caused the energy loss.

Focused ion beam

Focused ion beam, also known as FIB, is a technique used particularly in the semiconductor industry, materials science and increasingly in the biological field for site-specific analysis, deposition, and ablation of materials. A FIB setup is a scientific instrument that resembles a scanning electron microscope (SEM). However, while the SEM uses a focused beam of electrons to image the sample in the chamber, a FIB setup uses a focused beam of ions instead.