Publications by Emile Jacques de Rijk

Study of additive manufactured microwave cavities for pulsed optically pumped atomic clock applications

Additive manufacturing (AM) of passive microwave components is of high interest for the cost-effective and rapid prototyping or manufacture of devices with complex geometries. Here, we present an experimental study on the properties of recently demonstrate ...

AIP American Institute of Physics2018

Compact Orthomode Transducer with Broadband Beamforming Capability

Juan Ramon Mosig, Anja Skrivervik, Emile Jacques de Rijk

A compact and broadband orthomode transducer (OMT) with two dual linearly polarized ports is reported here for the first time. The component is based on a combination of two ridged Boifot junctions through a series of power dividers that act as an embedded ...

IEEE2018

3D printed microwave cavity for atomic clock applications: proof of concept

Anja Skrivervik, Emile Jacques de Rijk

The authors present the realisation and characterisation of an additively manufactured (AM) microwave resonator cavity for double-resonance (DR) vapour-cell atomic clocks. The design of the compact microwave cavity is based on the loop-gap resonator approa ...

2018

Atomic clock microwave cavity: 3D Printing microwave resonator cavities for atomic clocks

Anja Skrivervik, Emile Jacques de Rijk

2018

High-Field Liquid-State Dynamic Nuclear Polarization in Microliter Samples

Stefano Alberti, Jean-Philippe Ansermet, Jérémy Genoud, Emile Jacques de Rijk

2018

Four-Port Broadband Orthomode Transducer Enabling Arbitrary Interelement Spacing

Juan Ramon Mosig, Anja Skrivervik, Emile Jacques de Rijk, Tomislav Debogovic, Maria Garcia Vigueras, Santiago Capdevila Cascante, Esteban Menargues Gomez

This paper reports a novel methodology to design broadband orthomode transducers with two arbitrarily spaced ports carrying orthogonal linear polarizations. The component is based on a combination of two Boifot junctions through a series of power dividers ...

Institute of Electrical and Electronics Engineers2018

Polymer-Based Metal Coated Additive Manufactured V- and W-band Antenna Feed Chain Components

Juan Ramon Mosig, Emile Jacques de Rijk, Tomislav Debogovic, Santiago Capdevila Cascante, Esteban Menargues Gomez

In this paper an additive manufactured (AM) W-band monolithic feed chain is presented. The feed chain, which consists of a corrugated horn antenna and a turnstile orthomode transducer (OMT), operates over the entire W-band (75-110 GHz) and fulfills typical ...

IEEE2017

Cost-effective dual-polarised leaky-wave antennas enabled by three-dimensional printing

Juan Ramon Mosig, Emile Jacques de Rijk, Tomislav Debogovic, Maria Garcia Vigueras, Esteban Menargues Gomez

This study proposes a compact dual-polarised directive radiator whose complex prototyping is enabled by additive manufacturing. In addition to monolithic implementation, stereolitography followed by metal coating, it also provides high radio-frequency perf ...

Inst Engineering Technology-Iet2017

Polymer-Based Additive Manufacturing of High-Performance Waveguide and Antenna Components

Jean-Philippe Ansermet, Emile Jacques de Rijk, Tomislav Debogovic, Mathieu Billod

In this paper, a lightweight horn antenna array demonstrator is designed and fabricated by means of an additive manufacturing (AM) process that has been optimized for complicated passive radio-frequency (RF) components. The presented design comprises a com ...

Ieee-Inst Electrical Electronics Engineers Inc2017

W-Band Waveguide Filters Fabricated by Laser Micromachining and 3-D Printing

Emile Jacques de Rijk, Mathieu Billod, Cheng Guo

This paper presents two W-band waveguide bandpass filters, one fabricated using laser micromachining and the other 3-D printing. Both filters are based on coupled resonators and are designed to have a Chebyshev response. The first filter is for laser micro ...

Institute of Electrical and Electronics Engineers2016