Publication

Novel structured adsorber and oxidation catalysts for the removal of VOCs in low concentration

Kim Martin Nikolajsen
2007
EPFL thesis
Abstract

One possibility for the removal of volatile organic compounds (VOCs) is catalytic oxidation. For the removal of VOCs in low concentration (≲ 3000 ppmv for propane) it is not possible to sustain the required oxidation temperature over the catalyst without external heating. An approach to overcome this problem is to concentrate the VOC by adsorption, in a "two-step adsorption-incineration" process. This is an unsteady state process in which the VOC laden effluent gas is cleaned by passing it through an adsorber. Once the adsorber is saturated the VOC is desorbed by heating and purging. The concentrated VOC from the desorber can then be oxidized over the catalyst, producing enough heat to sustain the oxidation temperature. Conventional adsorbents have some drawbacks such as tailing during desorption due to the large particle size, high pressure drop and hot-spot formation. The objective of this work was to develop, characterize and test the adsorbent and catalyst, with low resistance to mass transfer resulting from thin films of active material, for the two-step adsorption-incineration process. Both the adsorbent and the oxidation catalysts were supported on sintered metal fibers (SMF). This is a novel, structured support offering several advantages over conventional randomly packed beds: Low pressure drop, due to the high porosity of the SMF, which is important where large flow rates and/or high quantities of gas must be treated. High thermal conductivity, due to the metallic nature, leading to smaller temperature gradients in the fixed-bed. A very high geometric surface area, due to the small fiber size. On the order of 200,000 m2/m3 with a fiber diameter of 20 µm. Furthermore, a mathematical model was developed to show the feasibility of the coupling of the two steps in the process. The adsorber was made from a thin, homogeneous film of MFI-type zeolite covering the fibers of the SMF. The film was grown by the seed-film method by hydrothermal treatment. A 3 µm film was obtained with 10 wt.% zeolite on the fiber after 24 h synthesis at 125 °C. This material had a specific surface area of 30 m2/g. The adsorption equilibrium of propane was described well by the Langmuir isotherm and the heat of adsorption was found to be ΔH0ads = - 43.1 kJ/mol. Isothermal breakthrough curves were measured as a function of temperature and film thickness. A mathematical model, comprised of a tanks-in-series model with a linear driving force (LDF) mass transfer description, successfully described the breakthrough behavior. The overall mass transfer was found to be solely due to diffusion in the zeolite film. However, the thin films show very low resistance to mass transfer leading to low internal concentration gradients and efficient utilization of the adsorbent. The pressure drop was measured and compared to that of a randomly packed fixed-bed of spheres. The equivalent diameter for a constant volumetric flow rate and superficial cross sectional area was dp = 180 µm, for a fiber diameter of df = 26 µm at 10 wt.% zeolite loading. The oxidation catalysts were all supported on SMF and cobalt oxide was used as the active phase. Three different groups of catalysts were developed. The support was modified by coating the fibers either with a thin film of fine powder (alumina or catalyst powder) or with a MFI-type zeolite film identical to the adsorbent. The third group was made from cobalt oxide impregnated directly on the oxidized fibers. The latter type of catalyst was found to be the most active during the screening experiments. The base support composition was varied (stainless steel (SS), FeCrAlloy and inconel) to investigate the support effect on the kinetics. The stainless steel and FeCrAlloy supports had similar activities, surpassing that of the inconel supported catalyst, which might be attributed to a Co3O4 surface enriched with iron from the support. Between the 1.1 wt.%Co3O4/SMFSS and 1.5 wt.%Co3O4/SMFFeCrAlloy catalyst the FeCrAlloy based had the highest normalized activity at low temperature (< 310 °C), low propane mole fraction (0.13 %) and high oxygen mole fraction (16.7 %). The chemical kinetics were determined from a novel and efficient experimental design. The apparent activation energy for this catalyst was found to be 87.5 ± 2.6 kJ/mol, with reaction orders in propane of 0.38 ± 0.04 and in oxygen of 0.30 ± 0.08. The catalysts were tested up to 350 °C. Mass transfer limitations were absent and the kinetics was described well with the power rate law as compared to the Mars-van Krevelen model. Catalysts based on Co3O4, supported directly on oxidized SMF, are very active catalysts, simple to prepare, withstand deactivation due to hot-spot formation and show great potential in comparison to the industrial reference catalyst (copper and manganese oxide supported on alumina). The adiabatic desorption process was investigated by mathematical modeling. Simply purging the adsorption bed with the hot exhaust gas from the reactor cannot result in the concentration of the VOC due to the high heat capacity of the fixed-bed. Hence, it will be necessary to use either a high heat carrier like steam, with the adverse effects of drying and separation of water and VOC, or an approach in which the desorber is heated prior to purging the bed, changing the adsorption equilibrium in favor of high gas concentrations. For the latter method, the minimum theoretical propane mole fraction for an autothermal process was found to be 350 ppmv to sustain a catalytic incinerator at 250 °C. Finally, it can be concluded that for the first time zeolite films on SMF were used as structured adsorbents, leading to very low internal mass transfer and increased process efficiency. Furthermore, the advantages of the SMF can be exploited in a catalytic oxidizer, which can be combined with the adsorber to annihilate VOCs in low concentrations. A novel method for the deposition of fine powder catalyst on SMF was also developed for the first time.

About this result
This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.
Related concepts (40)
Adsorption
Adsorption is the adhesion of atoms, ions or molecules from a gas, liquid or dissolved solid to a surface. This process creates a film of the adsorbate on the surface of the adsorbent. This process differs from absorption, in which a fluid (the absorbate) is dissolved by or permeates a liquid or solid (the absorbent). Adsorption is a surface phenomenon and the adsorbate does not penetrate through the surface and into the bulk of the adsorbent, while absorption involves transfer of the absorbate into the volume of the material, although adsorption does often precede absorption.
Tandem mass spectrometry
Tandem mass spectrometry, also known as MS/MS or MS2, is a technique in instrumental analysis where two or more mass analyzers are coupled together using an additional reaction step to increase their abilities to analyse chemical samples. A common use of tandem MS is the analysis of biomolecules, such as proteins and peptides. The molecules of a given sample are ionized and the first spectrometer (designated MS1) separates these ions by their mass-to-charge ratio (often given as m/z or m/Q).
Proton-transfer-reaction mass spectrometry
Proton-transfer-reaction mass spectrometry (PTR-MS) is an analytical chemistry technique that uses gas phase hydronium reagent ions which are produced in an ion source. PTR-MS is used for online monitoring of volatile organic compounds (VOCs) in ambient air and was developed in 1995 by scientists at the Institut für Ionenphysik at the Leopold-Franzens University in Innsbruck, Austria. A PTR-MS instrument consists of an ion source that is directly connected to a drift tube (in contrast to SIFT-MS no mass filter is interconnected) and an analyzing system (quadrupole mass analyzer or time-of-flight mass spectrometer).
Show more
Related publications (159)

Co-Adsorption of Alcohols and Water in JUK-8 Studied Using Quasi-Equilibrated Thermodesorption

Pattaraphon Rodlamul

JUK-8 ([Zn(oba)(pip)]n, oba2- = 4,4 '-oxybis(benzenedicarboxylate), pip = 4-pyridyl-functionalized benzene-1,3-dicarbohydrazide) is a hydrolytically stable flexible metal-organic framework. Owing to its unusual adsorptive properties, JUK-8 can be considere ...
MDPI2024

Adsorption of Copper by Naturally and Artificially Aged Polystyrene Microplastics and Subsequent Release in Simulated Gastrointestinal Fluid

Florian Frédéric Vincent Breider, Thibault Béranger Masset, Lu Zhou

Microplastics, especially aged microplastics can become vectors of metals from environment to organisms with potential negative effects on food chain. However, a few studies focused on the bioavailability of adsorbed metals and most studies related to aged ...
2024

Adsorption of Copper by Naturally and Artificially Aged Microplastics and Subsequent Release in Simulated Gastrointestinal Fluid

Florian Frédéric Vincent Breider, Thibault Béranger Masset, Lu Zhou

Microplastics, especially aged microplastics can become vectors of heavy metals from environment to organisms with potential negative effects on food chain. However, a few studies focused on the bioavailability of adsorbed metals and most studies related t ...
ChemRxiv2023
Show more
Related MOOCs (16)
SES Swiss-Energyscope
La transition énergique suisse / Energiewende in der Schweiz
SES Swiss-Energyscope
La transition énergique suisse / Energiewende in der Schweiz
Plasma Physics: Introduction
Learn the basics of plasma, one of the fundamental states of matter, and the different types of models used to describe it, including fluid and kinetic.
Show more

Graph Chatbot

Chat with Graph Search

Ask any question about EPFL courses, lectures, exercises, research, news, etc. or try the example questions below.

DISCLAIMER: The Graph Chatbot is not programmed to provide explicit or categorical answers to your questions. Rather, it transforms your questions into API requests that are distributed across the various IT services officially administered by EPFL. Its purpose is solely to collect and recommend relevant references to content that you can explore to help you answer your questions.