Modeling of Local Cell Degradation in Solid Oxide Fuel Cells: Cumulative Effect of Critical Operating Points

A CFD model was developed to predict with accuracy the local electrochemical performance in an operating solid oxide fuel cell. A particular focus was given on the study of performance limitations and degradation sources caused by the design of the fuel cell, by the choice of materials and components, or by improper operating points. The model is used to understand typical degradation effects observed on stacks tested in collaboration with HTCeramix - SOFCpower. The model is able to predict several degradation effects caused by the use of compressive seal materials with remaining open porosity. Diffusion across seals is modeled, as well as the resulting parasitic combustion of air and fuel. The risk of local redox-cycling for the anode supported cell is evaluated locally, as well as an eventual local reduction of the cathode layers. The cracking of electrolyte caused by redox cycles is modeled locally, with increasing gas leakage at each cycle, allowing to model the cumulative effect of successive critical operating points. The results are compared with experiments, showing an overall good agreement.

Préparation et caractérisation de nanoparticules bimétalliques (Pt-Au) sur un substrat en diamant dopé au bore

Bahaa El Roustom

Using petrol as a main source of energy, during the 20th century, has caused considerable amounts of damage among which are atmospheric pollution and global warming. At the same time, many geologists and economists expect that the discovery rate of new petrol sources will not follow the market's demand causing a serious shortage of petrol in the near future. These alarming perspectives have motivated scientists around the world to develop new clean and renewable energy sources. It is in that objective that electrochemists intensified their research in order to develop the fuel cell technology. This latter consists in directly converting chemical energy into electricity. The main advantage of this technology over traditional energy production is that the fuel cell energy efficiency is Carnot cycle independent. The theoretical efficiency of such an energy source is nearly 90%. Direct Alcohol Fuel Cell (DAFC), fed by ethanol on one hand and by air (oxygen) in the other hand, is a very interesting option for such kind of energy production. Ethanol is a renewable energy source of vegetal origin whose CO2 production is consumed by plants during the cycle. Even though Pt has long been known to be a perfect catalyst for DAFC, it has some principal limitations, the most important ones being poisoning by intermediate products (OH on the cathodic side and CO on the anodic side) and a relatively high cost compared to other materials. These problems have pushed the experts in the field to focalize their research on the development of more suitable and better performing materials. Gold nanoparticles have shown a surprising catalytic activity, very different from the bulk, making them a preferential candidate to replace Pt. A system based on using two or more metals as catalysts (example Au-Pt) dispersed on an appropriate substrate seems to be also an interesting candidate to enhance the cell's efficiency. The substrate should be chemically inert, non-oxydable and should not present any interference with the electrochemical and electrocatalytic behaviour of the nanoparticles. In the first part, the employed substrate, which is boron doped diamond (BDD) is characterized. The substrate's main characteristics are its chemical inertness, its weak residual current and its resistance to corrosion. These characteristics contribute to making the substrate an ideal support for nanoparticles. In this work, the substrate is a diamond film, but for fuel cell applications diamond should be used as powder or dispersed particles. In chapters III and IV, we studied the effect of boron incorporation on the morphology and the behaviour of the diamond film. For this purpose, samples with different ratios of boron/carbon (B/C) in the vapour phase during preparation were characterized (B/C = 300, 1000, 2500 and 6000 ppm). Results showed that the grain size decreases with increasing boron content in the film. This is accompanied by a transition towards a quasi-metallic character. It was also found that graphitic impurities in the diamond film increase when the B/C ratio increases. We also established some graphitic impurities increase in the diamond film when the ratio of B/C increases. The identity of these impurities was established in chapter III as being surface redox couples (semi-quinone/semi-hydroquinone). Using cyclic voltametry we were able to observe a total elimination (B/C=300 ppm) or partial elimination (B/C=6000 ppm) of these surface redox couples. We also found in chapter IV that these surface redox couples are responsible of the electrochemical activity of the BDD electrode. BDD electrodes with different doping level B/C=300, 1000 and 6000 ppm) in the vapour phase are modified with IrO2 nanoparticles using the method of thermal decomposition. Our results showed that, at low potentials, the behaviour of the composite electrode IrO2/BDD with respect to the reaction of oxygen evolution is independent of the doping level. On the other hand, at high potentials, the weakly doped electrode (B/C=300 ppm) presents a supplementary overpotential due to the interface BDD-IrO2. An approach based on the double junction is developed in this work describing two distinct behaviours depending on the boron concentration in the diamond film. A new method for Au nanoparticles deposition on highly doped BDD electrodes (B/C= 2500 ppm) is presented in chapter VI. This method involves two steps: the first step consists on sputtering the equivalent of few nanolayers of Au on the diamond surface; the second step is a heat treatment in air at high temperatures. Several parameters that could influence the dispersion, the stability as well as the diameter of the Au nanoparticles are studied. In chapter VII, the behaviour of the composite electrode Au/BDD is studied in a solution containing redox couples in acid media. This electrode was simulated as an arrangement of active Au microelectrodes dispersed on a less active BDD substrate. The overall behaviour of the composite electrode (Au/BDD) has been related to the electrochemical rate constants on each material. In chapter VIII, another new synthesis method for a bimetallic system formed by Au and Pt nanoparticles dispersed on a BDD substrate is developed. This method consists in electrodepositing a small amount of Pt on a composite electrode Au/BDD. Our results showed that Pt was preferentially deposited on Au covering its whole surface. In fact, Au nanoparticles serve as germ of nucleation for Pt. In the following step, the bimetallic PtbAu/BDD is heated to 400°C in air to enhance the interaction between Au and Pt. The experiments showed that Au reappeared on the surface. The electrochemical behaviour of the bi-metallic electrode is characterized by a negative shift in the peak potential of reduction of Pt oxides. This is not the case of heterogeneous alloys obtained by the fusion of two metals at high temperatures. The composite electrode Au/BDD as well as the bi-metallic electrode Pt-Au/BDD are used for electrocatalytic applications. The studied reaction in chapter IX is the oxygen reduction reaction (ORR) in an acid medium. We found that the number of exchanged electrons increases with increasing the amount of Pt at the surface. Oxygen is reduced into H2O2 on the Au/BDD electrode and into H2O on the Pt-Au/BDD electrode. In chapter X we studied the reaction of oxidation of oxalic acid. The behaviour of both Au and Pt electrodes seemed very similar for this reaction. The bi-metallic electrode containing both Pt and Au on its surface has shown an intermediate behaviour between the behaviour of the two metals.

EPFL2006

Stability and performance of tape cast anode supported electrolyte (ASE) cells.

Raphaël Ihringer, Jan Van Herle

Recent progress in our development of anode supported electrolyte (ASE) SOFcells is reported. The cells are fabricated by cocasting of aqueous slurries of NiO/YSZ and 8YSZ, followed by cofiring. A gradient cathode is deposited by screenprinting successive layers of LSM/YSZ composite and lanthanum cobaltite, followed by a 2nd firing step. Full cells show a final thickness of ? 0.25 mm, high flexibility and reasonable warpage. Proper anode current collection is crucial and obtained by cofiring an additional outer layer together with the substrate. Power density can reach 0.2 W/cm2 at 600°C with active cathodes (LSC, short-lived) and >1 W/cm2 at 810°C with the LSM cathode. Stability was tested during 2900 h, giving an average degradation of 3%/1000 h at 0.5 A/cm2 current density. Degradation can be delayed by short-time polarisation at higher current density: e.g. “reactivation” at 0.85 A/cm2 (30 min.) delayed degradation by 300 h.

European Solid Oxide Fuel Cell Forum2002

Alternative anode materials for methane oxidation in solid oxide fuel cells

Joseph Sfeir

Fuel Cells are electrochemical devices that are able to directly convert chemical energy to electrical energy, without any Carnot limitation. Hence, their energy efficiencies are relatively high. Among the various types of fuel cells, solid oxide fuel cells (SOFC) are operated at high temperatures and in principle can run on various fuels such as natural gas and hydrogen. As natural gas is sought to become one of the main fuels of the next decades, its direct feed to a SOFC is desirable as the reaction free energy is high CH4 + 2O2 = CO2 + 2H2O, ΔrG°800°C = -800.8kJ/mol At present, conventional SOFC are operated with pure hydrogen or partially to fully reformed natural gas implying an efficiency penalty. SOFC anodes are generally made of electrocatalytically active Ni-YSZ cermet. Pure CH4 is not fed directly to the anode, because of problems associated with the anode deactivation and coking as CH4 leads to the detachment of Ni particles from the YSZ support and their encapsulation by carbon. To overcome this problem, partially oxidized or reformed CH4 is used. For SOFCs running on direct CH4 feed, alternative anode materials to Ni-YSZ, or new anode formulations are necessary. However, in this case, several parameters influence the anode performance and stability. The anodes should withstand reduction at a low PO2 of around 10-24 atm, be compatible with the SOFC electrolyte, possess an acceptable conductivity and thermal expansion coefficient, and appropriate catalytic and electrocatalytic properties along with low coking activity. LaCrO3 and CeO2-based materials as well as some metal catalysts were studied here for their potential application as anodes in direct oxidation of CH4. This choice of materials was made as lanthanum chromite and ceria-based materials are mixed conductors known to resist quite well to the very reducing conditions in SOFC as they are commonly used for interconnect and electrolyte materials respectively. Moreover, these compounds possess some catalytic activity for CH4 activation and combustion. LaCrO3 and CeO2-based materials show rather low electrical conductivity (on the order of 1 S/cm in reducing conditions), necessitating the application of an extra material for proper current collection. Nevertheless, these oxides possess many of the stringent characteristics cited above. For SOFC anode purposes, LaCrO3-based compounds, substituted with Ca, Sr, Mg, Mn, Fe, Co and Ni, were synthesized by a modified citrate route from nitrate precursors. An optimal calcination temperature of 1100°C was found to be necessary to obtain XRD-pure yet sinteractive compounds. Conductivity measurements in air and in reducing atmospheres of 10-21 atm showed that the La A-site substituents (Ca and Sr) influenced the conductivity more than the Cr B-site substituents (Mg, Mn, Fe, Co and Ni). In humidifed H2, the total conductivity was maximally of 6.5 S/cm. Surface reaction with YSZ electrolyte was evidenced by SEM, XPS and SIMS, in reducing conditions, especially under current load, when these powders were applied as anodes. A current induced demixing effect was noted for heavily substituted LaCrO3. Ceria-based compounds, doped with Y, Nb, Pr and Gd, were synthesized through 3 different techniques: the solid-state method, coprecipitation and the NbCl5 route. The coprecipitation route was found to be most appropriate for Y, Pr and Gd, whereas for Nb a modified precipitation and the NbCl5 technique were the most efficient. Co-doping of Nb and Gd or Pr was studied in order to increase the electronic as well as the ionic conductivity in CeO2. Among all dopants, Nb was found to promote most the adhesion to YSZ electrolyte sheets. Adding Nb to Gd-doped ceria improved the electrode adhesion on YSZ sheets, but deteriorated its conductivity in oxidizing conditions. No interfacial reaction with YSZ was observed by HRTEM when Nb-doped ceria anodes were sintered on YSZ at 1200°C/4h. Catalytic measurements were undertaken with these materials in CH4 rich atmospheres. Different reaction mixtures were chosen to simulate the various SOFC operating conditions: partial oxidation, CO2 reforming by recycling and H2O reforming. Among the different elements, Sr and Ni were found to be the most active substituents for LaCrO3, as they promote all three types of reactions. The combination of both elements is favorable not only for catalytic use, but also for electrode application as they tend to increase the electronic conductivity of the material. Temperature programmed oxidation (TPO) and TEM made on the catalysts after runs in CH4, showed a very low carbon coverage over these oxides, except in the case of Fe substitution, over which carbon deposition was promoted. XPS analysis showed also that all B-site substituted compounds did not segregate after the catalytic runs whereas Ca and Sr (A-site substituents) tended to segregate in H2 and H2O rich atmospheres. Thermodynamic calculations, made using correlations developed in literature, show that Ca and Sr are expected to segregate in H2 and H2O rich atmospheres as they tend to form volatile hydroxyl species. Also, the thermodynamic stability of the LaCrO3 was observed to depend much on the substitution. For CeO2-based oxides, the activity for steam reforming increased from Nb