Publication

Compact transient thermal model for 3D ICs with liquid cooling via enhanced heat transfer cavity geometries

Related publications (42)

Evaluation of Heat Transfer Coefficients for an Impingement Cooling Cascade: Experimental Challenges and Preliminary Results

Peter Ott, Alexandros Terzis, Michele Gaffuri

In this paper, a modification of the widely used transient liquid crystal heat transfer measurement technique for impingement cooling is presented, in which a constant heat flux at the surface is used to drive the experiment, instead of a step change in th ...

2018

Two-phase operational maps, pressure drop, and heat transfer for flow boiling of R236fa in a micro-pin fin evaporator

John Richard Thome, Navid Borhani, Mirco Magnini, Chiara Falsetti, Hamideh Jafarpoorchekab

Cooling the new generation of 3D high power electronic chips is one of the leading challenges in microelectronics, as it is a key to achieve high computational performance at lower cooling system power consumption, thus reducing the operating cost. Two-pha ...

Pergamon-Elsevier Science Ltd2017

Innovative low-mass cooling systems for the ALICE ITS Upgrade detector at CERN

Manuel Gómez Marzoa

The Phase-1 upgrade of the LHC to full design luminosity, planned for 2019 at CERN, requires the modernisation of the experiments around the accelerator. The Inner Tracking System (ITS), the innermost detector at the ALICE experiment, will be upgraded by r ...

EPFL2016

Two-Phase Heat Transfer Mechanisms within Plate Heat Exchangers

Raffaele Luca Amalfi

Plate heat exchangers are adopted in many domestic and industrial applications, such as ventilation, air conditioning, evaporation or condensation process, heat pumps and cooling of hydrodynamic circuits in engines. In the present thesis, an extensive expe ...

EPFL2016

10.1 A pin-efficient 20.83Gb/s/wire 0.94pJ/bit forwarded clock CNRZ-5-coded SerDes up to 12mm for MCM packages in 28nm CMOS

Mohammad Amin Shokrollahi, Seyed Armin Tajalli, Christoph Walter, Ali Hormati, Anant Pratap Singh, Omid Talebi Amiri, Klaas Lammert Hofstra, Sergio Pesenti

High-speed signaling over package substrates is key to delivering the promise of 2.5D integration. Applications abound and include high-density memory interfaces, sub-division of large dies to increase yield and lower development time, sub-division of a di ...

2016

A Chip-Level Post-CMOS Via-Last Cu TSV Process for Multi-Layer Homogeneous 3D Integration

Seniz Esra Küçük, Yusuf Leblebici, Woo Yeong Cho

In this paper, a die-level CMOS post-processing scheme for 3D integration using the via-last approach is presented for multi-layer stacking. The process includes TSV fabrication, chip-to-chip bonding, and finally the TSV filling with Cu electroplating. The ...

Ieee2016

Modeling of Two-Phase Evaporative Heat Transfer in Three-Dimensional Multicavity High Performance Microprocessor Chip Stacks

John Richard Thome, Jackson Braz Marcinichen, Yassir Madhour, Brian Paul D'Entremont, Bruno Michel

Three-dimensional (3D) stacking of integrated-circuit (IC) dies increases system density and package functionality by vertically integrating two or more dies with area-array through-silicon-vias (TSVs). This reduces the length of global interconnects and t ...

American Society of Mechanical Engineers2014

3D-ICE: a Compact Thermal Model for Early-Stage Design of Liquid-Cooled ICs

David Atienza Alonso, Arvind Raj Mahankali Sridhar, Alessandro Vincenzi

Liquid-cooling using microchannel heat sinks etched on silicon dies is seen as a promising solution to the rising heat fluxes in two-dimensional and stacked three-dimensional integrated circuits. Development of such devices requires accurate and fast therm ...

Institute of Electrical and Electronics Engineers2014

Dynamic Modeling and Experimental Evaluation of a Controlled Two-Phase On-Chip Cooling System Designed for High Efficiency Datacenters

Nicolas Lamaison

An important challenge for the next generation of high performance datacenters is to guarantee sufficient, reliable, green and cheap cooling of the server blades. Since this seems unrealistic with air cooling technologies due to the expected ever higher ch ...

EPFL2014

A Semi-Analytical Thermal Modeling Framework for Liquid-Cooled ICs

David Atienza Alonso, Arvind Raj Mahankali Sridhar, Mohamed Mostafa Sabry Aly

While possessing the potential to replace conventional air-cooled heat sinks, inter-tier microchannel liquid cooling of 3D ICs also creates the problem of increased thermal gradients from the fluid inlet to outlet ports [1, 2]. These cooling-induced therma ...

Institute of Electrical and Electronics Engineers2014

Graph Chatbot

Chat with Graph Search

Ask any question about EPFL courses, lectures, exercises, research, news, etc. or try the example questions below.

DISCLAIMER: The Graph Chatbot is not programmed to provide explicit or categorical answers to your questions. Rather, it transforms your questions into API requests that are distributed across the various IT services officially administered by EPFL. Its purpose is solely to collect and recommend relevant references to content that you can explore to help you answer your questions.