Numerical Simulations of a Prechamber Autoignition Engine Operating on Natural Gas

At our laboratory extensive research has been conducted on the conversion of conventional Diesel cogeneration engines to operation on natural gas and biogas. In the framework of this research, a numerical simulation of a prechamber autoignition gas engine has been performed based on an experimental test case. With a simplified finite-rate/eddy-dissipation model for the combustion of natural gas, it was possible to properly reproduce the experiment considering the combustion duration, ignition timing and overall energy balance. A modification of the original cylindrical-conical prechamber geometry to a simpler cylindrical one was tested with the simulation model. The influence of burnt gases inside the prechamber was assessed simulating ghe mixture formation inside the prechamber. The simulations showed little effect of taking into account the non-homogeneities in the gas phase on the cumbustion duration. The new cylindrical geometry envisaged did not show any improvement in the combustion homogeneity inside the prechamber and its volume (limited by the real engine geometry) is in fact not sufficient to properly ignite the main chamber according to the simulations. The model can be used to further guide design modifications of the prechamber engine to improve performance.

Numerical simulations of a prechamber autoignition cogeneration engine operating on natural gas

Daniel Favrat, Stefan Heyne, Grégory Millot

A numerical model for a prechamber autoignition gas engine under development has been established based on an experimental test case. With a simplified finiterate/ eddy-dissipation model for the combustion of natural gas, it was possible to properly reproduce the experiment considering the combustion duration, ignition timing and overall energy balance. The predefined empiric constant of the eddydissipation model had to be increased by a factor of 10. A modification of the original cylindrical-conical prechamber geometry to a simpler cylindrical one was tested with a simulation. The influence of burnt gases inside the prechamber was assessed simulating the mixture formation inside the prechamber. The simulations showed little effect of taking into account the non-homogeneities in the gas phase on the combustion duration. The cylindrical geometry tested did not show any improvement in the combustion homogeneity inside the prechamber and its volume (limited by the real engine geometry) is not sufficient to properly ignite the main chamber.

2009

Numerical simulations of a prechamber autoignition cogeneration engine operating on natural gas

Daniel Favrat, Stefan Heyne, Grégory Millot

A numerical simulation of a prechamber autoignition gas engine has been performed based on an experimental test case. With a simplified finite-rate/eddy-dissipation model for the combustion of natural gas, it was possible to properly reproduce the experiment considering the combustion duration, ignition timing and overall energy balance. However the predefined empiric constant of the eddy-dissipation model had to be increased by a factor of 10. A modification of the original cylindrical-conical prechamber geometry to a simpler cylindrical one was tested with the simulation model. The influence of burnt gases inside the prechamber was assessed simulating the mixture formation inside the prechamber. The simulations showed little effect of taking into account the non-homogeneities in the gas phase on the combustion duration. The simulation showed that the new and cylindrical geometry envisaged did not show any improvement in the combustion homogeneity inside the prechamber and its volume (limited by the real engine geometry) is in fact not sufficient to properly ignite the main chamber. The model can be used to further guide design modifications of the prechamber engine to improve performance.

2007

Prechamber autoignition in natural gas engines

Daniel Favrat, Stefan Heyne, Jan-Bernhard Vos

Unscavanged prechamber ignition has been developed at the Laboratory of Industrial Energy Systems to reduce the emissions from cogeneration spark ignition gas engines, operating with both natural gas and biogas. Demonstration has been made that a lean burn engine unit equipped with optimized prechambers allows efficient operation, while remaining below the Swiss limits [1,2]. Further development aims at using prechambers operating in autoignition mode similar to HCCI (Homogeneous charge compression ignition). The advantages are on the one hand that there is no need for maintenance and replacement of the spark plugs which usually have a limited life time while on the other hand we are expecting to benefit from the HCCI characteristics, e.g. low NOx emission levels. The prechamber configuration though should be a system easier to control than an engine operating completely in HCCI mode. The investigation of the applicability of this technique for engines used in the transport sector with rapidly changing operating conditions might be a further step in the development. In order to better understand the phenomena, simulations are done taking into account both fluid dynamics and chemical kinetics. Ignition delay measurements with mixtures of methane, ethane and propane have been conducted at the Rapid compression machine facility at the University of Lille at varying stoichiometric ratios. These measurements are used as a basis to choose an appropriate chemical mechanism for combustion simulation. The kinetic solver CHEMKIN has been used for zero-dimensional simulations at TDC conditions of the rapid compression machine to reproduce the ignition delays. Several detailed combustion mechanisms have been applied for these simulations, e.g. GRI 3.0 + RAMEC, n-Heptane and PRF mechanisms (LLNL) and Konnov’s mechanism. The aim is to obtain a reduced mechanism that will be used in combination with computational fluid dynamics. In order to do this, sensitivity and reaction pathway analysis is performed, as well as multi- objective optimization of the kinetic parameters. In cooperation with CFS engineering a coupling between the CFD code NSMB (Navier Stokes Multi Block) and the chemical solver CHEMKIN has been established enabling a simulation of the experiments conducted with the rapid compression machine. Further steps will be the design of a prechamber to be used with an experimental mono-cylinder engine and the simulation of the in-cylinder flow with prechamber to determine the influencing factors for controlling the autoignition event. Behaviour at part load as well as in transient conditions will also be investigated.

2005

Prechamber autoignition in natural gas engines

Daniel Favrat, Stefan Heyne, Jan-Bernhard Vos

2005