Investigation on the dynamics of electron transport and recombination in TiO2 nanotube/nanoparticle composite electrodes for dye-sensitized solar cells

In this work, the fabrication and characterization are reported of dye-sensitized solar cells based on TiO2 nanotube/nanoparticle (NT/NP) composite electrodes. TiO2 nanotubes were prepd. by anodization of Ti foil in an org. electrolyte. The nanotubes were chem. sepd. from the foil, ground and added to a TiO2 nanoparticle paste, from which composite NT/NP electrodes were fabricated. In the composite TiO2 films the nanotubes existed in bundles with a length of a few micrometers. By optimizing the amt. of NT in the paste, dye-sensitized solar cells with an efficiency of 5.6% were obtained, a 10% improvement in comparison to solar cells with pure NP electrodes. By increasing the fraction of NT in the electrode the c.d. increased by 20% (from 11.1-13.3 mA cm-2), but the open circuit voltage decreased from 0.78-0.73 V. Electron transport, lifetime and extn. studies were performed to investigate this behavior. A higher fraction of NT in the paste led to more and deeper traps in the resulting composite electrodes. Nevertheless, faster electron transport under short-circuit conditions was found with increased NT content, but the electron lifetime was not improved. The electron diffusion length calcd. for short-circuit conditions was increased 3-fold in composite electrodes with an optimized NT fraction. The charge collection efficiency was more than 90% over a wide range of light intensities, leading to improved solar cell performance.

Strategies to Optimizing Dye-Sensitized Solar Cells

Sophie Wenger

Dye-sensitized solar cells (DSCs) constitute a novel class of hybrid organic-inorganic solar cells. At the heart of the device is a mesoporous film of titanium dioxide (TiO2) nanoparticles, which are coated with a monolayer of dye sensitive to the visible region of the solar spectrum. The role of the dye is similar to the role of chlorophyll in plants; it harvests solar light and transfers the energy via electron transfer to a suitable material (here TiO2) to produce electricity — as opposed to chemical energy in plants. DSCs are fabricated of abundant and cheap materials using inexpensive processes (e.g. screen-printing) and are likely to be a significant contributor to the future commercial photovoltaic technology portfolio. The work conducted during this thesis aimed at optimizing the DSC using three different strategies: The use of versatile organic sensitizers for stable and efficient DSCs, the study of tandem device architectures in combination with other solar cells to harvest a larger fraction of the solar spectrum, and the development of a validated optoelectric model of the DSC. Organic donor-π-acceptor dyes are an interesting alternative to the standard metal-organic complexes used in DSCs. Efficient photovoltaic conversion and stable performance could be demonstrated with three classes of donor systems, namely diphenylamine, difluorenylaminophenyl, and π-extended tetrathiafulvalene. The highest conversion efficiencies were obtained with a difluorenylaminophenyl donor system (η = 8.3 % with a volatile electrolyte and η = 7.6 % with a solvent-free ionic liquid, which was a new record for organic dyes at the time of publication). Surprisingly, efficient regeneration of the oxidized dye by the I-/I3- redox mediator was found with the π-extended tetrathiafulvalene system, even though the thermodynamic driving force was as low as 150 mV. So far driving forces of 300-500 mV had been regarded as necessary for efficient regeneration of the dye cation. Also, important structure-property relationships pertaining to the recombination of electrons with the electrolyte and to the stability of the device could be identified (i.e. effect of linear vs. branched structure, linker length, and moieties used). The power conversion efficiency of solar cells can be extended beyond the limit for a single cell (∼ 30 %) by using multiple cells with different optical gaps in a tandem device. DSCs and chalcopyrite Cu(In,Ga)Se2 (CIGS) solar cells have complementary optical gaps and are thus suitable systems for integration in a tandem device. It was shown that a monolithic DSC/CIGS tandem device has the potential for increased efficiency over a mechanically stacked device due to increased light transmission to the bottom cell, and a monolithic DSC/CIGS device with an initial efficiency of η = 12.2 % was demonstrated. The degradation of the devices — induced by the corrosion of the CIGS cell in contact with the I-/I3- redox mediator — could be retarded with a protective thin conformal ZnO/TiO2 oxide layer coated on the CIGS cell by atomic layer deposition. Finally, an experimentally validated optical and electrical model of the DSC has been developed to assist the optimization process, which is predominantly conducted by empirical means in the DSC research community. The optical model allows to accurately calculate the internal quantum efficiency of devices, i.e. the ratio of extracted electrons to absorbed photons by the dye, a crucial and so far difficult to determine characteristic. Intrinsic parameters — like injection efficiency, electron diffusion length, or distribution of trap states in the TiO2 — can be extracted from experimental steady-state and time-dependent data with the electric model. The model allows to make a comprehensive and quantitative loss analysis of the different optical and electric loss channels in the DSC. The model has been implemented with a graphical user interface for straightforward usage. All three optimization strategies — organic dyes, tandem architecture, and device modeling — developed during this thesis make a valuable contribution to the development and commercialization of inexpensive and high efficiency DSCs. They enable a comprehensive view of the system and pave the way for a systematic analysis and reduction of losses, which has been the ultimate route to success for several established photovoltaic technologies.

EPFL2010

A small electron donor in cobalt complex electrolyte significantly improves efficiency in dye-sensitized solar cells

Ulf Anders Hagfeldt, Yasemin Saygili, Lei Zhang

Photoelectrochemical approach to solar energy conversion demands a kinetic optimization of various light-induced electron transfer processes. Of great importance are the redox mediator systems accomplishing the electron transfer processes at the semiconductor/electrolyte interface, therefore affecting profoundly the performance of various photoelectrochemical cells. Here, we develop a strategy-by addition of a small organic electron donor, tris(4-methoxyphenyl)amine, into state-of-art cobalt tris(bipyridine) redox electrolyte-to significantly improve the efficiency of dye-sensitized solar cells. The developed solar cells exhibit efficiency of 11.7 and 10.5%, at 0.46 and one-sun illumination, respectively, corresponding to a 26% efficiency improvement compared with the standard electrolyte. Preliminary stability tests showed the solar cell retained 90% of its initial efficiency after 250 h continuous one-sun light soaking. Detailed mechanistic studies reveal the crucial role of the electron transfer cascade processes within the new redox system.

Nature Publishing Group2016

Solid state nanocrystalline titanium oxide photovoltaic cells

The dye solar cell, is a novel photoelectrochemical solar cell presenting unique advantages, as the use of low cost materials and the potential simplicity of manufacturing. However, a liquid electrolyte is actually required for the transport of the photogenerated positive charges. A major breakthrough is the replacing of the liquid electrolyte by a solid-state hole conducting material – the aim of this work. First, the metal/TiO2 junction was investigated, with either silver or gold as rectifying contact. Sensitization was demonstrated, as action spectra were measured using different dyes. The evaporated metal could not enter the pores of the nanocrystalline TiO2 to contact all the dye molecules, hence only low photovoltaic performances were obtained. Furthermore, these metal/TiO2 junctions showed a high sensitivity to humidity and to forward bias polarization. The use of an electrically conducting polymer, poly(bithiophene), was studied in a metal/polymer junction and in TiO2/polymer devices with flat and nanocrystalline TiO2 electrodes. The photoelectric characterizations indicated that electrochemically reduced poly(bithiophene) was able to inject electrons into TiO2, i.e. sensitizing TiO2, and it acted as a hole conducting layer. Short-circuit current densities of 2-3 mA/cm2 were measured at an irradiation of 1.2 W/cm2. The open-circuit voltages were in the 250-350 mV range, depending on the light intensity and temperature. The use of a transparent hole conducting material, CuI, which is a wide bandgap p-type semiconductor, was demonstrated in a nanocrystalline junction made of highly porous sensitized TiO2 and solution-cast CuI. A short-circuit current of 1 mA/cm2 was achieved under one sun simulated light; the open-circuit voltage was 600 mV and the light-to-power conversion efficiency was 0.3 %. The peak quantum efficiencies of 8 % in the UV, and 3 % in the visible, showed that the nanocrystalline junction was working inefficiently, probably due to the poor electrical contact between the TiO2 nanocrystallites and the CuI crystals. Furthermore, the sensitizer was not tuned to inject holes into the valence band of CuI. As conclusion, a controlled-capillary pore based sensitized device is suggested. In this concept, all the internal surface of the TiO2 electrode coated with sensitizer is contacted with the transparent hole conducting layer, hence improving the photovoltaic properties of the device.

EPFL1996

Strategies to Optimizing Dye-Sensitized Solar Cells

Sophie Wenger

EPFL2010

Solid state nanocrystalline titanium oxide photovoltaic cells

EPFL1996