Design and Measurement of a Differential Printed Antenna for a Wireless Sensor Network Node

Nuno Miguel Faria Pires, Anja Skrivervik Favre
Ieee-Inst Electrical Electronics Engineers Inc, 2017
Journal paper

Abstract

This letter presents the design and measurement of an antenna integrated into an agricultural sensor network node operating on the 2.4-GHz ISM band using the ZigBee protocol stack. The novel structure, coined bowtie-shaped folded dipole (BSFD), has a differential 100-Omega input impedance matching a particular controller widely used in wireless sensor network (WSN) applications. This letter also presents a survey of existing WSN antennas to which the proposed design compares favorably. The challenges of testing a differential antenna using conventional single-ended equipment are addressed regarding antenna impedance and radiation pattern measurements. The differential antenna input impedance was confirmed with four different test setups using a conventional vector network analyzer. The radiation pattern of the proposed antenna was measured in-prototype resorting to a spectrum analyzer. The measured patterns show that the proposed antenna has a maximum received power over 4 dB compared to two early versions of the WSN node that used commercial off-the-shelf antenna solutions. The performance was also confirmed in a field test where a BSFD-equipped prototype achieved close to a 300-m range, tripling that typical for ZigBee applications.

Official source

https://infoscience.epfl.ch/record/230816?ln=en

About this result

This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.

Related concepts

Related publications

Related publications (16)

Small antennas as wireless system components

Nuno Miguel Faria Pires

Small antennas, or more specifically, electrically small antennas, are passive radiating elements whose size is much smaller than the operating wavelength. The current wireless application systems usually have size constraints that, for the most common operating frequencies except the highest, also implies small electrical size. This applies to most of the wireless systems in a wide variety of applications such as consumer and medical devices, sensor networks and military. The design of small antennas brings forward some challenges that are not obvious when considering large antennas radiating into free-space for line-of-sight communications, the realm of classical radio systems. Small antennas are nowadays deployed in very different conditions, usually integrated into device packaging and/or operating near dispersive media such as the human body. The typical antenna characterization was devised for the classical scenario, an ideal case that bares low resemblance to the highly variable deployments, might not be very useful in predicting the antenna performance. This should be taken into account in the design cycle as small antenna performance is heavily dependent on the close surroundings. This thesis proposes some novel tools and insights towards the objective of a more system integrated antenna design cycle. It begins by studying efficiency, an antenna parameter specially relevant for small antennas. It is so because small antennas are usually omnidirectional and in this case the simple figure of merit can grasp most of the antenna spacial radiation characteristics. The result of this study is the proposal of a novel technique to measure antenna radiation efficiency using small overmoded metallic cavities in a very large band. It is based on simple input reflection coefficient measurements and the suggested post-processing can successfully decrease the effect of cavity resonances. This was the main limiting factor in measuring antenna efficiency in small metallic cavities. The technique requires only readily available laboratory equipment. It was compared to existing alternatives that are also subjected to improvements. Three different antenna prototypes, with significant and different antenna efficiency characteristics were used for the comparison. The approach provides a controlled environment providing the possibility to experimentally validate simulation models that can be confidently used in more complex situations, such as close to the body. The second part of this thesis reports on several small antennas where the wireless system as a whole was considered in the design cycle. It begins by considering Body Area Network (BAN) systems were a small antenna is expected to operate near the human body or subjected to deformations when built in flexible material for integration into garments. In this context, the development of simplified computational models for a limb compared favorably to other more complex solutions when predicting antenna performance near the body. A simple dielectric loading technique was refined and confirmed to reduce antenna-human body interactions, increasing the antenna matching performance without major impacts on other antenna parameters. A flexible antenna was built in plastic material and characterized when subjected to deformations. In the field of Wireless Sensor Networks (WSN) two design workflow examples are given. One antenna was built and tested for usage in the base-stations [...]

EPFL2014

Time-domain performance of a patch-loaded band-reject UWB antenna

Nuno Miguel Faria Pires, Mohsen Koohestani, Anja Skrivervik Favre

A previous study of a novel technique to design a band-reject UWB monopole antenna by using patch loading is extended. Frequency-domain measurements have confirmed that the antenna designed using this technique rejects the interfering signal at the two intended narrowband frequency ranges. Moreover, the antenna radiation pattern distortion is negligible except at the notched bands. A study of time-domain characteristics based on the antenna pulse response and system fidelity factor is presented. The time performance has been extracted from frequency-domain measurements using a standard method. The obtained time-domain results promise the suitability of the proposed technique to design band-reject antennas useful for future UWB system applications.

Institution of Engineering and Technology2013

, ,

In recent years, an increasing number of pioneering studies have been carried out in the field of acoustic metamaterials, following the path of electromagnetic metamaterials. These artificial engineered materials are designed in such a way so as to achieve new macroscopic properties, like negative refraction, that are not readily present in nature. While the design and the fabrication of these artificial materials is a hot topic among scientists in different fields of physics such as photonic, electromagnetic, acoustic and recently mechanic, an important part of the scientific research is now oriented towards the identification of actual applications for these structures. As the novel idea of metamaterial was first developed in the electromagnetic realm and for the microwave frequency range, it is somehow more mature in these fields than in acoustics. Metamaterial applications are now widely developed in electromagnetics especially for the design of new antenna. Among other examples, metamaterial concepts are aiming at reducing the coupling between two adjacent radiating elements of the array and increasing the operating bandwidth of radiating elements. It is also used for phase compensation in microwave transistors, and many more applications are rising in the recent literature. In year 2009, in analogy with electromagnetic transmission line metamaterial, our group proposed a concept of acoustic transmission line metamaterial, consisting of a waveguide periodically loaded with membranes along the duct, and transverse open channels (denoted “stubs”). Based on our proposed structure and in analogy with applications of transmission line electromagnetic metamaterials, researchers proposed the idea of an acoustic counterpart to the “backward wave antenna”. These antennas or radiating devices have a very special property such that the radiation angle or the directivity changes with the frequency. In this article, a comprehensive, step by step, design methodology for acoustic backward wave antenna is presented. For this purpose we use the model proposed in our 2009 publication for acoustic transmission line metamaterial, but we focus the discussion on the optimization of the antenna performance. We also propose some closed form formulas for the practical design of such devices, and a formal validation of the structure is proposed using Comsol Multiphysics.

2013

, ,

2013

Small antennas as wireless system components

Nuno Miguel Faria Pires

EPFL2014