Charge-carrier Dynamics in Metal Oxides and Hybrid Lead Perovskites investigated by Time-Resolved UV and X-ray Spectroscopy

In modern ultrafast optoelectronic technologies based on wide band gap insulators, the non-equilibrium dynamics of photogenerated charges plays a major role. Unravelling the mechanisms of interaction between these charge carriers and their environment is crucial to support the design of more efficient devices. Especially, the absorption of photons with more energy than the optical band gap generates electrons-hole pairs (EHP) whose transport and dissociation as excitons or free charge carriers is of pivotal importance for the charge separa- tion at photovoltaic interfaces. The advent of ultrafast pump-probe optical spectroscopy in the deep-UV provides access to the dynamics of EHP through a variety of transient modifications of the optical spectrum. In this Thesis, the cooling of electrons in ZnO and methylammonium lead bromide perovskite (MAPbBr3), two broadly used direct band gap semiconductors, is tracked as they end up and accumulate at the bottom of the conduction band. ZnO has a fast cooling time of the order of 100 fs which efficiently converts photon excess energy into lattice heat while MAPbBr3 has a rather slow electron cooling time of the order of 400 fs, favorable for charge separation at interfaces as it drives the injection of hot carriers. Additionally, the high energy carried by the UV probe photons provides access to the photodynamics at different high symmetry points in the Brillouin zone. In a second step, these two semiconductors have been associated to other materials to form prototypical photovoltaic assemblies such as dye-sensitized (ZnO/N719) and solid-state lead perovskite sensitized (TiO2/MAPbBr3) interfaces. Upon electron injection into the transition metal oxide (ZnO or TiO2), dramatic changes are observed in the absorption close to the optical band gap from which the timescale of electron injection is obtained. It highlights how slight screening length and chemical potential changes can generate large modifications in the optical properties through many-body effects. At both interfaces, a delayed appearance of the electron at the bottom of the conduction band is observed which is due the formation of a bound state. This Thesis extends beyond the band insulators to the photodynamics of NiO, a strongly correlated charge-transfer insulator. Excitation above the optical band gap generates a large photoinduced absorption below the optical band gap which is characteristic of the interplay between electronic and low energy bosonic excitations. The dressing of electronic excitations with bosonic modes generates low energy excitation modes on ultrafast timescales which generate a competition between itinerant and localized resonances with a high degree of tunability. The progress made in resonant X-ray based time-resolved spectroscopies allows the investigation of the degree of charge localization around specific atoms in a system. Photogenerated electron localization in NiO is studied by time-resolved X-ray absorption spectroscopy, causing bond elongations and the formation of an electron-polaron in less than 100 ps. In a last part, the linear dichroism of the steady-state X-ray absorption spectrum of anatase TiO2 at the K-edge is studied which provides an unambiguous assignment of the pre-edge transitions as their orbital composition is strongly anisotropic and sensitive to the crystal orientation.

Strategies to Optimizing Dye-Sensitized Solar Cells

Sophie Wenger

Dye-sensitized solar cells (DSCs) constitute a novel class of hybrid organic-inorganic solar cells. At the heart of the device is a mesoporous film of titanium dioxide (TiO2) nanoparticles, which are coated with a monolayer of dye sensitive to the visible region of the solar spectrum. The role of the dye is similar to the role of chlorophyll in plants; it harvests solar light and transfers the energy via electron transfer to a suitable material (here TiO2) to produce electricity — as opposed to chemical energy in plants. DSCs are fabricated of abundant and cheap materials using inexpensive processes (e.g. screen-printing) and are likely to be a significant contributor to the future commercial photovoltaic technology portfolio. The work conducted during this thesis aimed at optimizing the DSC using three different strategies: The use of versatile organic sensitizers for stable and efficient DSCs, the study of tandem device architectures in combination with other solar cells to harvest a larger fraction of the solar spectrum, and the development of a validated optoelectric model of the DSC. Organic donor-π-acceptor dyes are an interesting alternative to the standard metal-organic complexes used in DSCs. Efficient photovoltaic conversion and stable performance could be demonstrated with three classes of donor systems, namely diphenylamine, difluorenylaminophenyl, and π-extended tetrathiafulvalene. The highest conversion efficiencies were obtained with a difluorenylaminophenyl donor system (η = 8.3 % with a volatile electrolyte and η = 7.6 % with a solvent-free ionic liquid, which was a new record for organic dyes at the time of publication). Surprisingly, efficient regeneration of the oxidized dye by the I-/I3- redox mediator was found with the π-extended tetrathiafulvalene system, even though the thermodynamic driving force was as low as 150 mV. So far driving forces of 300-500 mV had been regarded as necessary for efficient regeneration of the dye cation. Also, important structure-property relationships pertaining to the recombination of electrons with the electrolyte and to the stability of the device could be identified (i.e. effect of linear vs. branched structure, linker length, and moieties used). The power conversion efficiency of solar cells can be extended beyond the limit for a single cell (∼ 30 %) by using multiple cells with different optical gaps in a tandem device. DSCs and chalcopyrite Cu(In,Ga)Se2 (CIGS) solar cells have complementary optical gaps and are thus suitable systems for integration in a tandem device. It was shown that a monolithic DSC/CIGS tandem device has the potential for increased efficiency over a mechanically stacked device due to increased light transmission to the bottom cell, and a monolithic DSC/CIGS device with an initial efficiency of η = 12.2 % was demonstrated. The degradation of the devices — induced by the corrosion of the CIGS cell in contact with the I-/I3- redox mediator — could be retarded with a protective thin conformal ZnO/TiO2 oxide layer coated on the CIGS cell by atomic layer deposition. Finally, an experimentally validated optical and electrical model of the DSC has been developed to assist the optimization process, which is predominantly conducted by empirical means in the DSC research community. The optical model allows to accurately calculate the internal quantum efficiency of devices, i.e. the ratio of extracted electrons to absorbed photons by the dye, a crucial and so far difficult to determine characteristic. Intrinsic parameters — like injection efficiency, electron diffusion length, or distribution of trap states in the TiO2 — can be extracted from experimental steady-state and time-dependent data with the electric model. The model allows to make a comprehensive and quantitative loss analysis of the different optical and electric loss channels in the DSC. The model has been implemented with a graphical user interface for straightforward usage. All three optimization strategies — organic dyes, tandem architecture, and device modeling — developed during this thesis make a valuable contribution to the development and commercialization of inexpensive and high efficiency DSCs. They enable a comprehensive view of the system and pave the way for a systematic analysis and reduction of losses, which has been the ultimate route to success for several established photovoltaic technologies.

EPFL2010

Nanoparticle sensitisation of solid-state nanocrystalline solar cell

Robert Plass

Over the past fifteen years dye-sensitised nanocrystalline solar cells have been the subject of intense research and development efforts. These systems provide a technically and economically credible alternative to classical p-n junction solar cells, reaching over 10 % certified efficiency under standard solar illumination conditions (AM 1.5, 1000 W/m2). Recently, the liquid electrolyte, commonly used in these dye-sensitised solar cells, could successfully be replaced by a novel solid hole-conducting material (spiro-OMeTAD). The absence of volatile solvents and corrosive components like iodine presents a clear advantage of these solid-state devices over their photoelectrochemical counterparts. Yet, their maximum overall efficiency of about 3 % clearly lacks behind the performance features of classical dye-sensitized solar cells. The objective of this work is the replacement of the usually used sensitiser (transition metal complexes and organic dyes) by quantum-dots. It was motivated by the possibility to achieve panchromatic light absorption due to the size-dependent properties of the quantum-dots. Some studies have been published using quantum-dots of inorganic low-bandgap semiconductors as sensitisers for mesoporous wide bandgap semiconductor electrodes in conjunction with liquid electrolytes. These systems often suffer from corrosion and photo-corrosion mainly due to the aggressive nature of the electrolyte employed. Solid-state organic-inorganic heterojunctions might provide the desired environment for quantum-dot sensitisation, as the environment is much less aggressive. A large variety of inorganic quantum-dot materials like PbS, CdS, PbSe and CdSe were scrutinized for their use as sensitisers. All particles were synthesised in situ on the TiO2 surface using two different techniques: dip-coating and chemical bath deposition. Lead sulphide was the most investigated due to its superior photovoltaic characteristics. High Resolution Transmission Electron Microscopy (HRTEM) of PbS sensitised TiO2 electrodes fabricated via dip-coating clearly showed the distinct particles on the surface of the semiconductor. The electron transfer dynamics following optical excitation of quantum-dot sensitized TiO2/spiro-OMeTAD heterojunctions were thoroughly studied. Fluorescence spectroscopy was used to prove the possible electron injection from the PbS into the TiO2. Nanosecond laser spectroscopy was applied to monitor the interfacial recombination of the injected electron and the oxidised hole-conductor. Femtosecond laser spectroscopy allowed measuring the ultra-fast kinetics in the system, including electron trapping, exciton recombination and PbS regeneration. An overall efficiency of 0.5 % at 0.1 sun (AM 1.5) has been reached with such systems. Chemical bath deposition (CBD) of PbS leads to the formation of a layer rather than distinct particles on the TiO2. Solar cells fabricated via CBD exhibited open-circuit voltages which were generally 100 mV higher then those of comparable devices made via dip-coating. The PbS layer acts as blocking layer, hindering the contact between TiO2 and the hole-conductor. This technique allowed achieving devices highly linear with respect to the illumination power. Different strategies were pursued to impede interfacial recombination, among which the introduction of self-assembled monolayers at the interface between the organic and inorganic phases was proven to be the most efficient. Nanosecond laser spectroscopy showed a strong decrease of the interfacial recombination kinetic rates in the presence of hexadecylmalonic acid or decylphosphonic acid monolayers. Short-circuit currents could be raised by a factor two to four using such type of molecules. The overall efficiency of the device could be strongly increased, reaching 1 % at 0.1 Sun (AM 1.5). CBD was also used to deposit PbSe and CdSe layers at the surface of TiO2. Fluorescence spectroscopy was used to probe electron injection from CdSe quantum dots to TiO2. Generally it was observed that metal sulfides were more efficient in sensitizing TiO2/OMeTAD heterojunctions then the respective selenides.

EPFL2004

Electronic and structural modification of titanium dioxide/zinc oxide photoanode for dye-sensitized solar cells

Aravind Kumar Chandiran

Dye-sensitized solar cells (DSC) are a new class of molecular photovoltaics that mimics the natural photosynthesis, for the direct conversion of sunlight into electricity. A typical DSC is a sandwich of a dye sensitized nanoparticle TiO2 film and a catalyst coated counter electrode, with a redox electrolyte filling the space in between. The high internal surface area of the mesoporous TiO2 film ensures higher dye uptake for an efficient light harvesting. Following the light illumination, an electron from the highest occupied molecular orbitals (HOMO) of the dye is excited to its lowest unoccupied molecular orbitals (LUMO). Due to an effective electronic orbital coupling between dye and TiO2, the excited electrons are injected into TiO2. The oxidized dye is regenerated by the electron donor present in the electrolyte. The circuit is completed by the transfer of photogenerated electrons in TiO2 via an external load, to counter electrode regenerating the oxidized electrolyte species. In a conventional DSC, the transport rate of the photogenerated electrons in TiO2 competes with the parasitic electron recombination, as these two processes occur at a similar ms time domain. This thesis work is aimed at the fundamental understanding of these electron transfer processes at sensitized photoanodes that were subject to different bulk and surface electronic structural modifications. The implications were shown to be of profound interest for the fabrication of high efficiency and low cost dye-sensitized solar cells. In the first part of the thesis, the bulk electronic structure of the anatase TiO2 nanoparticles is modified by the incorporation of different concentrations of aliovalent cations (Nb5+, Ga3+, Y3+) in the crystal lattice. The cationic doping/substitution in the nanoparticles is achieved by hydrothermal process. The modified nanoparticles retained the parent anatase crystal structure of TiO2. The transparent dye-sensitized solar cells made with these modified films, using our standard heteroleptic metal complex sensitizers and iodide/triiodide redox electrolyte, displayed enhanced photovoltaic performances, at certain added concentrations. Charge extraction measurements in DSC, reveals a formation of deeper trap states below the conduction band of titanium dioxide when Nb ion is incorporated into the TiO2 lattice. On the other hand, Ga3+ and Y3+ did not significantly affect the trap states distribution compared to the reference device. The modification in the trap states and the oxygen stoichiometry due to these cation inclusions significantly influenced the electron recombination and transport rates. These properties are investigated in detail using transient decay techniques. Following the study on the electronic structure of the bulk TiO2, the influence of the surface modification of the TiO2 nanoparticles on the electron transfer dynamics is investigated. The kinetics of electron recombination from TiO2 to the single electron redox shuttles is fast, leading to a significant loss in the open-circuit potential (VOC) of devices. The emergence of cobalt complexes as a potential electrolyte motivated us to investigate the role of surface passivation of the titanium dioxide nanoparticles. Insulating sub-nanometer oxide tunneling layers deposited by atomic layer deposition (ALD) are known to block the electron recombination, thereby, leading to an increase in the VOC and the collection efficiency of the solar cell. A general perception in the DSC community is that any insulating oxide layer can block the recombination. However, in this work, it is unraveled that, just the insulating property of oxides is not sufficient. In addition, the properties such as the conduction band position and the oxidation state of the insulating oxide, the electronic structural modification induced to the underlying TiO2 mesoporous film, modification of surface charges (isoelectric point) and charge of the electrolyte species have to be considered. A complete photovoltaic study has been done by depositing different cycles (by ALD) of four insulating oxides (Ga2O3, ZrO2, Nb2O5 and Ta2O5) and their recombination characteristics, surface electronic properties, transport rate and injection dynamics are investigated with a standard organic dye and Co2+/Co3+ redox mediator. A comparison is made with the conventional iodide/triiodide electrolyte. The second part of the thesis is focused at the development of new type of photoanodes for effective electron transport to increase the charge collection efficiency. We present a way of utilizing thin and conformal overlayer of titanium dioxide or zinc oxide on an insulating mesoporous template as a photoanode for dye-sensitized solar cells. Different thicknesses of TiO2 ranging from 1 to 15 nm are deposited on the surface of the template by ALD. This systematic study helps unraveling the minimum critical thickness of the TiO2 overlayer required to transport the photogenerated electrons efficiently. A merely 6 nm thick TiO2 film on a 3 μm mesoporous insulating substrate is shown to transport 8 mA/cm2 of photocurrent density along with ≈900 mV of open-circuit potential, when using our standard donor-π-acceptor sensitizer and Co(bipyridine)3 redox mediator. The three dimensional conformal shell on the insulating core also exhibits one order of magnitude higher transport rate compared to the conventional TiO2 nanoparticles. Similar nanostructures were made by depositing ZnO on an insulating template and the electron transfer properties are compared with titania. We also developed ALD recipe for the deposition of crystalline TiO2 or ZnO at low temperatures (< 200 °C) on arbitrary mesoporous insulating templates, considering their prospects of making photoanodes on flexible plastic substrates. The experience gained about the deposition of conformal and pin-hole free TiO2 layer in the previous section is extended for the high efficiency solid-state mesoscopic solar cells based on CH3NH3PbI3 perovskite absorbers. We show that a 2 nm as-deposited ALD overlayer on a mesoporous TiO2 film, printed on a bare conducting glass, is sufficient to arrest the recombination process that lead to a power conversion efficiency of 11.5 %. A detailed investigation on the electron back reaction is presented using electrochemical impedance spectroscopy.

EPFL2013