Reversible solid-oxide cell stack based power-to-x-to-power systems: Comparison of thermodynamic performance

Philippe Aubin, Tzu-En Lin, François Maréchal, Maria del Mar Perez Fortes, Jan Van Herle, Ligang Wang, Yumeng Zhang
2020
Journal paper

Abstract

The increasing penetration of variable renewable energies poses new challenges for grid management. The economic feasibility of grid-balancing plants may be limited by low annual operating hours if they work either only for power generation or only for power storage. This issue might be addressed by a dual-function power plant with power-to-x capability, which can produce electricity or store excess renewable electricity into chemicals at different periods. Such a plant can be uniquely enabled by a solid-oxide cell stack, which can switch between fuel cell and electrolysis with the same stack. This paper investigates the optimal conceptual design of this type of plant, represented by power-to-x-to-power process chains with x being hydrogen, syngas, methane, methanol and ammonia, concerning the efficiency (on a lower heating value) and power densities. The results show that an increase in current density leads to an increased oxygen flow rate and a decreased reactant utilization at the stack level for its thermal management, and an increased power density and a decreased efficiency at the system level. The power-generation efficiency is ranked as methane (65.9%), methanol (60.2%), ammonia (58.2%), hydrogen (58.3%), syngas (53.3%) at 0.4 A/cm2, due to the benefit of heat-to-chemical-energy conversion by chemical reformulating and the deterioration of electrochemical performance by the dilution of hydrogen. The power-storage efficiency is ranked as syngas (80%), hydrogen (74%), methane (72%), methanol (68%), ammonia (66%) at 0.7 A/cm2, mainly due to the benefit of co-electrolysis and the chemical energy loss occurring in the chemical synthesis reactions. The lost chemical energy improves plant-wise heat integration and compensates for its adverse effect on power-storage efficiency. Combining these efficiency numbers of the two modes results in a rank of round-trip efficiency: methane (47.5%) > syngas (43.3%) ≈ hydrogen (42.6%) > methanol (40.7%) > ammonia (38.6%). The pool of plant designs obtained lays the basis for the optimal deployment of this balancing technology for specific applications.

Official source

https://infoscience.epfl.ch/record/279561?ln=en

About this result

This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.

Related concepts (32)

Related concepts

Related publications (97)

Related publications

Triple-mode grid-balancing plants via biomass gasification and reversible solid-oxide cell stack: Concept and thermodynamic performance

Chengzhou Li, Tzu-En Lin, François Maréchal, Maria del Mar Perez Fortes, Jan Van Herle, Ligang Wang, Yumeng Zhang

Biomass-to-electricity or -chemical via power-to-x can be potential flexibility means for future electrical grid with high penetration of variable renewable power. However, biomass-to-electricity will not be dispatched frequently and becomes less economically-beneficial due to low annual operating hours. This issue can be addressed by integrating biomass-to-electricity and -chemical via ‘‘reversible’’ solid-oxide cell stacks to form a triple-mode grid-balancing plant, which could flexibly switch among power generation, power storage and power neutral (with chemical production) modes. This paper investigates the optimal designs of such a plantconcept with a multi-time heat and mass integration platform considering different technology combinationsand multiple objective functions to obtain a variety of design alternatives. The results show that increasing plant efficiencies will increase the total cell area needed for a given biomass feed. The efficiency difference among different technology combinations with the same gasifier type is less than 5% points. The efficiency reaches up to 50%–60% for power generation mode, 72%–76% for power storage mode and 47%–55% for power neutral mode. When penalizing the syngas not converted in the stacks, the optimal plant designs interact with the electrical and gas grids in a limited range. Steam turbine network can recover 0.21–0.24 kW electricity per kW dry biomass energy (lower heating value), corresponding to an efficiency enhancement of up to 20%points. The difference in the amounts of heat transferred in different modes challenges the design of a common heat exchange network.

2020

Small scale SOFC systems

Nordahl Autissier

The increasing cost of carbon based fuels pushes the electricity generation market towards more efficient electricity generation technologies. In this context, fuel cells offer the opportunity to increase efficiency and lower CO2 and NOx emissions, in particular with co-generation units. The complexity, as well as the number and different combinations of components involved with a SOFC stack make their analysis impossible without dedicated tools. The simultaneous consideration of economic and thermodynamic considerations is a key challenge for engineers and decision makers. The present work contributes to the development of design tools for fuel cells and energy systems. A detailed model of fuel cell stack and a model of a complete system were developed. Based on a commercial CFD code, additional routines were implemented to model the electro-chemical behavior of a fuel cell as well as the reforming reaction schemes. The model is able to predict cell behavior under various fuel feeds. The detailed 3-D model of stack repeat unit allowed to identify weaknesses of a first stack geometry. With the combination of experimental observations and modeling activities, specific problems of the existing concept were identified and a new geometry designed, together with the corresponding stack concept. A new stack design is presented with successful experiments up to 1 kWe. Besides the stack, a co-generation fuel cell system is composed of multiple components such as heat exchangers, reformer, recycle loops... The number, the type and size of those components influence the system costs but also its efficiencies (thermal and electrical). A multi-objective thermo-economic optimization methodology was defined, allowing to optimize at the same time the configuration and operating parameters of a system. This method was applied to two sizes of co-generators : a 1 kW unit and a 30 kW unit. HTceramix SA (Yverdon, Switzerland) is developing part of a co-generation unit. The work indicates the potential improvement of their prototype. The 1 kW unit was optimized in a first phase on thermal and electrical efficiencies, and in a second phase on electrical efficiency and installed costs. Those two results indicate the influence of the objective function selection on the results. The high operating temperature of Solid Oxide Fuel Cells (SOFC) offers good opportunity for coupling with a gas turbine. A simple concept of pressurized SOFC-µGT was studied and optimized, for an net electrical output of 30 kW. The simple layout described in this work allows present technical feasibility of the concept. Moreover, the costs of electricity, lower than 0.20$/kWh, makes it economically viable solutions. The methodology and the tools developed allow the engineer to explore the solution space through optimal configurations, in order to select those fitting with its priorities and technical constraints.

EPFL2008

Amidst a backdrop of rapidly increasing world-wide electricity demand, solar thermal power generation shows great potential for supplying the electricity needs of numerous countries in the Sun-belt regions of the world. In these regions, the absence of significant biomass, hydrological or geothermal reserves makes solar thermal power the most promising solution for meeting that most fundamental of demands: energy. Amidst the different options available for harnessing the Sun’s power, solar thermal technologies have been shown capable of producing electricity at the most economically viable rates [32]. However, all currently existing solar thermal power plants have been based around the use of Rankine, or steam turbine, cycles which are limited in the efficiencies they can achieve. In order to make better use of the Sun’s energy, higher efficiency cycles should be used. With their high concentration ratios, solar thermal power tower systems are amongst the best options for making use of the Sun’s potential. As the energy delivery temperature of central receiver systems is higher, they harness the solar radiation at a higher exergy level [4]. This higher temperature also opens the road to the use of more advanced thermodynamic cycles. Hybrid fossil-fuel – solar systems are also imaginable [13], as the energy delivery temperature is compatible with standard gas turbine cycles. Hybrid systems can help mitigate the requirements of thermal energy storage, as well as reducing the perceived risk when investing in new solar technology, which stimulates research and development, as well as providing employment. Recent developments in the field of high temperature volumetric receivers [10] along with rock- based packed-bed storage systems have opened up an interesting possibility. High temperature receivers allow the use of higher-efficiency combined-cycle setups, whereas packed-bed units offer the possibility of cheap storage. Larger storage volumes allow pure-solar systems to extend their power production into the night, making hybrid options less attractive. This is compounded by the common practice of guaranteeing a preferred tariff for electricity sales from pure-solar sources With this in mind, a complete dynamic model of a power plant based on the pure-solar concept has been elaborated. The performance of the setup is evaluated over a range of days, using solar insolation profiles obtained from satellite data. In order to examine different design options and their impact on the performance of the power plant, a multi-objective, thermo-economic optimisation of both the power plant superstructure and operating conditions was performed using the new, dynamic models. By means of an evolutionary algorithm [17], a family of Pareto-optimal points were obtained, representing the trade-off between increased power plant efficiency, and lower levelised energy costs. Through use of optimisation, it was shown that exergetic efficiencies in the region of 21-27% can be achieved, for relatively low power outputs of between 3 and 11 MWe. These configurations correspond with levelised electricity costs in the region of 14-21 UScts/kWhe. In most regions, the use of solar power is encouraged by the guarantee of a preferential tariff for electricity sales from renewable sources. Sale of electricity at a price of around 24 UScts/kWhe [32] should therefore be imaginable, ensuring the economic viability of solar thermal power tower systems. It can be concluded that, when properly designed, solar thermal power plants based on combined cycles are both economically and thermodynamically promising. By raising the efficiency of the plant, the size of the solar collector field is diminished, increasing the otherwise low energy densities of solar power systems. By reducing the levelised electricity costs, solar thermal power plants become more economically viable, accelerating their construction and thus, hopefully, reducing our dependence on fossil-fuels.

2009

Small scale SOFC systems

Nordahl Autissier

EPFL2008