Induced giant piezoelectricity in centrosymmetric oxides

Piezoelectrics are materials that linearly deform in response to an applied electric field. As a fundamental prerequisite, piezoelectric materials must have a noncentrosymmetric crystal structure. For more than a century, this has remained a major obstacle for finding piezoelectric materials. We circumvented this limitation by breaking the crystallographic symmetry and inducing large and sustainable piezoelectric effects in centrosymmetric materials by the electric field–induced rearrangement of oxygen vacancies. Our results show the generation of extraordinarily large piezoelectric responses [with piezoelectric strain coefficients (d33) of ~200,000 picometers per volt at millihertz frequencies] in cubic fluorite gadolinium-doped CeO2−x films, which are two orders of magnitude larger than the responses observed in the presently best-known lead-based piezoelectric relaxor–ferroelectric oxide at kilohertz frequencies. These findings provide opportunities to design piezoelectric materials from environmentally friendly centrosymmetric ones.

In-situ structural investigations of ferroelasticity in soft and hard rhombohedral and tetragonal PZT

Dragan Damjanovic

Despite the technological importance of hard and soft PZT, Pb(Zr,Ti)O3, ceramics, the mechanisms of ferroelectric hardening and softening remain widely discussed in the literature. The hardening and softening phenomena have traditionally been investigated in relation with dielectric manifestations such as aging of the dielectric susceptibility and constriction of the polarization electric field hysteresis loop. Here, we present a systematic investigation of the ferroelectric and ferroelastic properties of soft and hard PZT in both the tetragonal and rhombohedral phases. A particular focus has been devoted to ferroelastic domain switching by characterizing the macroscopic mechanical constitutive behavior and in-situ synchrotron X-ray diffraction during compression. It is demonstrated that variation of the ordering state of point defects in PZT ceramics affects the switching behavior of both ferroelectric and ferroelastic domains under mechanical or electrical fields. Softening of the mechanical and electrical properties of originally hard PZT ceramics was conferred by quenching the materials from above the Curie temperature. The present findings are discussed with respect to the current understanding of hardening-softening transitions in ferroelectric materials.

American Institute of Physics2015

Poleable Dielectric Elastomer Composites

Yee Song Ko

As part of the recent efforts on renewable energies, energy harvesting by exploiting environmental motions and vibrations to generate electricity is being enthusiastically developed as a novel kind of green energy source. Piezoelectric materials are a logical choice for such applications, as they can readily generate electric charges when subjected to mechanical force without the need for additional equipment. While small deformations can be easily covered by traditional piezoelectrics, new materials have to be developed to access strains in excess of af few percent. This thesis lays out steps for the fabrication of a piezoelectric elastomer for use as active sensor and energy harvesting applications containing solely organic components. To achieve this a composite approach was chosen in which organic piezoelectric materials, so-called frozen-dipole electrets, were embedded as particulate fillers in a highly elastic polydimethyl siloxane (PDMS)matrix. Nanoparticles of a frozen-dipole electret material had to be prepared and characterized first, followed by their dispersion in the PDMS matrix, and finally the characterization of the composite elastomer. Poly-2-hydroxyethyl methacrylate (PHEMA) particles were produced byminiemulsion polymerization, and Disperse Red 1 (DR1) molecules were incorporated at the same time to turn the material into a frozen-dipole electret. The DR1 was introduced either as a blend or by copolymerization with amethacrylate-functionalized DR1 derivative. The study of PHEMA particles indicates that it would be very challenging to render them piezoelectric, due to their high conductivity, the environmental influence on their properties and unfavourable components introduced with the production method. In contrast, PMMA copolymer particles could easily be polarized. Polymethylmethacrylate (PMMA) copolymers with either methacrylate-functionalized DR1 or nitroaniline was used to produce nanoparticles via the nanoprecipitationmethod. Nanoparticles with up to 70 mol% DR1 could be obtained. These materials were chosen because of their known properties as electrets in order to serve as reference materials for the proof of concept of the organic piezoelectric elastomers. They were analysed by impedance spectroscopy and the thermally stimulated depolarization current technique to assess their relaxation and polarization behaviour. PMMA particles could be blended with PDMS without any additional additives to produce composite elastomers which can be turned into piezoelectric materials when poled in an electric field at high temperatures. Depending on the chain length of the PDMSmatrix, maximum strains of up to 600% could be reached. A custom built Berlincourt measuring setup was used to quantify the longitudinal piezoelectric coefficient d33 which was found to depend strongly on the force with which the composite is loaded. The transvere piezoelectric coefficient d31 was measured with a separate setup, based on a tensile testing machine. Piezoelectricity could be measured atmacroscopic strains as high as 200%. d31 initally decreases but stabilizes after a certain time. Most importantly, composites with PMMA-DR1 copolymer particles retain their piezoelectricity after exposure to elevated temperatures for several days.

EPFL2017

Conductivity, dielectric and piezoelectric properties of SrBi4Ti4O15

Strontium Bismuth Titanate is a very promising material for high temperature piezoelectric applications, its elevated ferroelectric phase transition (530°C), linear piezoelectric properties under low field and relatively low room temperature conductivity (compared to others Bismuth Titanates) make it very attractive for precision sensors. However, under severe conditions (low frequency, high field, high temperature or low oxygen partial pressure) some of those advantages disappear. Piezoelectric response is dominated by charge drift in general becomes unstable. Above all, at high temperature and low oxygen partial pressure, a large conductivity increase reduces the piezoelectric efficiency of the material, in this work, electrical conductivity, piezoelectric properties and dielectric permittivity of SrBIT ceramic have been investigated in conditions of high temperature, low oxygen partial pressure, low to moderate driving field and frequency. As a result of this research, a better understanding of SrBIT properties was achieved. Thanks to a careful study of SrBIT processing as a bulk ceramic, a reproducible route was established. Many basic mechanisms leading to both SrBIT crystallization and sintering have been identified. It was demonstrated that a detailed knowledge of the exact processing conditions is required in order to achieve high quality material. DC conductivity measurements were carried out as a function of temperature, oxygen partial pressure and dopant concentration. It was found that the apparent activation energy for conduction for undoped SrBIT was 1 eV between 140 and 220°C and 1.5 eV between 450 and 700°C. Decrease of the activation energy in the lower temperature range has been discussed considering grain boundary conductivity, as a transition from electronic to ionic conduction or as consequence of small polarons conduction. It was shown that lower activation energy resulted from Manganese doping (0.5 eV), this was interpreted as either growing influence of grain boundary conductivity as dopant concentration increases or as shallow hole trap formation. DC conductivity measurements and acceptor/donor doping experiments demonstrated p-type conductivity in the low temperature range (up to 220°C) as donor doping decreases conductivity, while oxygen partial pressure controlled measurements indicated n-type conductivity at higher temperature (above 700°C). An electrical impedance analysis was performed with several equivalent circuits. The aim of these models was to simulate the impedance of SrBIT. The best approximation was found with a distributed element of Havriliak-Negami type. However, as the physical justification for this circuit was not clear, the investigation of the grain, grain boundary and electrode impedances was performed with multiple discrete parallel RC elements. With temperature, grain size and oxygen activity variations, the identification of three separate contributions as grain, grain boundary and electrode was realized. The anisotropy of conductivity and permittivity was demonstrated with textured material and both DC and AC analysis. With the master curves built for the electrical modulus, it was found that the impedance probably related to Bismuth oxide layers produces an additional high frequency are. From this finding and by comparing characteristic relaxation frequencies of undoped, 2 mol.% Mn and 4 mol.% Nb SrBIT, it was determined that conductivity is higher in the ab plane direction than in the c direction within both perovskite units and Bismuth oxide layers. With conductivity measurements under controlled oxygen partial pressure, it was found that an acceptor-based (intrinsic or extrinsic) model could be used to describe the electrical conductivity under controlled oxygen partial pressure of both undoped and 2 mol.% Mn doped SrBIT. However, as neither a pO2-1/6 region (intrinsic oxygen vacancies compensated by electrons) for undoped SrBIT nor a pO2-1/4 region (oxygen vacancies compensated by singly ionized acceptors) for Mn doped SrBIT were seen, it was concluded that the acceptorcontrolled model is not sufficient for a complete description of SrBIT. For this reason and in order to include the low oxygen partial pressure behavior of undoped SrBIT, a donor-based (intrinsic) model was also considered. The source of intrinsic donors would be in that case Bi3+ cations sitting on Sr2+ sites in the perovskite sublattice. Considering Bismuth vacancies as the negative compensating species, both pO2-1/4 and pO2-independent regions could be predicted with the model. However, even if the donor-controlled model seems to better match conductivity measurements in the full PO2) range, rejecting the acceptor-based model would be an error. It is actually not demonstrated that in SrBIT the concentration of exchanged Bismuth cations is always (all temperature, pressure) larger than the natural acceptor impurity concentration. It is very likely that the cation exchange is dependent of the oxygen partial pressure. It is also not proved as suggested in the literature that direct compensation between exchanged Strontium and Bismuth exists, reducing the net donor-excess. With the acceptor-controlled model, the mass-action constants for reduction and for ionization of intrinsic carriers across the band gap were determined. The band gap of SrBIT was estimated to be 3.5 eV. The ionic conductivity of SrBIT was determined at high temperature with measurements under controlled oxygen partial pressure. It was found that the electrical conductivity of SrBIT is probably mixed (electronic and ionic) as the estimation of the transference number provided quite large values (t=0.8 at 800°C). From electronic and ionic conductivity data, mixed conduction can actually be predicted in a large temperature range (above room temperature). The piezoelectric measurements using direct effect demonstrated that it is actually possible to unlock piezoelectrically active ferroelectric domain walls and create non-linear piezoelectric properties in undoped SrBIT. This occurs above a threshold elastic field, which is thermally activated. With a piezoelectric composite, it was demonstrated that the electromechanical coupling between two different phases creates a piezoelectric relaxation. This one could be positive or negative depending on the respective properties of each composite's component. It was shown experimentally that a small temperature change is sufficient to transform a positive relaxation into a negative one. While these experiments did not provide a detailed microstructural explanation for the piezoelectric relaxation observed in 2 mol.% Mn doped SrBIT, they gave a first insight into an original phenomenological approach. Microstructure and piezoelectric properties were related with the calculation of a piezoelectric relaxation composite made of two textured samples. This demonstrated that a piezoelectric relaxation may occur just because of anisotropy. Microstructural reproduction of this coupling is actually an important feature of Aurivillius phases.

EPFL2000

Poleable Dielectric Elastomer Composites

Yee Song Ko

EPFL2017

Conductivity, dielectric and piezoelectric properties of SrBi4Ti4O15

EPFL2000