Publication

Preliminary Design of a High Current R&W TF Coil Conductor for the EU DEMO

Abstract

Paschen failures in ITER, W7-X and JT60 superconducting coils at the acceptance tests have shown that it is highly desirable to lower the coil discharge voltage (U-d) of the DEMO Toroidal Field (TF) coils. Another benefit of lowering the U-d might be the reduction of the number of coil feeders, i.e. connect in series several TF coils to a discharge unit, which is attractive for machine integration. For a given Ampere Turn (AT), one way to reduce the U-d is decreasing the coil inductance L. Since the inductance of a coil is proportional to N-2, where N is the number of turns, for a given total TF current N.I-op, decreasing the number of turns corresponds to a higher current flowing through each turn, which results this results in L proportional to I-op(-)2 to I (-)(2 )(op)This means that increasing the op op current will have a quadratic impact on L and thus a linear impact on the discharge voltage U-d making the design of a high-current (similar to 105 kA) CICC attractive for the EUROfusion DEMO project. In the case of DEMO, increasing the operating current from 66 kA to 105 kA leads to a reduction of the TF discharge voltage of a factor 1.6. Designing a high current TF coil conductor layout includes performing mechanical studies to investigate the TF coil mechanical stability during operation. This contribution will thus present the first design for a react-and-wind TF conductor made of Nb3Sn and Cu as stabilizer designed for an operating current of 105 kA alongside the results of a dedicated 2D mechanical analysis.

About this result
This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.
Related concepts (33)
Direct current
Direct current (DC) is one-directional flow of electric charge. An electrochemical cell is a prime example of DC power. Direct current may flow through a conductor such as a wire, but can also flow through semiconductors, insulators, or even through a vacuum as in electron or ion beams. The electric current flows in a constant direction, distinguishing it from alternating current (AC). A term formerly used for this type of current was galvanic current.
High voltage
High voltage electricity refers to electrical potential large enough to cause injury or damage. In certain industries, high voltage refers to voltage above a certain threshold. Equipment and conductors that carry high voltage warrant special safety requirements and procedures. High voltage is used in electrical power distribution, in cathode ray tubes, to generate X-rays and particle beams, to produce electrical arcs, for ignition, in photomultiplier tubes, and in high-power amplifier vacuum tubes, as well as other industrial, military and scientific applications.
Fusion power
Fusion power is a proposed form of power generation that would generate electricity by using heat from nuclear fusion reactions. In a fusion process, two lighter atomic nuclei combine to form a heavier nucleus, while releasing energy. Devices designed to harness this energy are known as fusion reactors. Research into fusion reactors began in the 1940s, but as of 2023, no device has reached net power. Fusion processes require fuel and a confined environment with sufficient temperature, pressure, and confinement time to create a plasma in which fusion can occur.
Show more
Related publications (55)

DEMO toroidal field coil fast discharge unit integration studies

Roberto Guarino, Alberto Ferro

The Fast Discharge Units (FDUs) of the Superconducting (SC) Toroidal Field (TF) coils in the European demonstration fusion power plant DEMO warrant the machine integrity over its full lifetime against severe failure events, such as SC coil quenches or any ...
Elsevier Science Sa2024

Inversing the actuation cycle of dielectric elastomer actuators for a facial prosthesis

Yves Perriard, Yoan René Cyrille Civet, Paolo Germano, Alexis Boegli, Thomas Guillaume Martinez, Stefania Maria Aliki Konstantinidi, Quentin Philippe Mario De Menech

Dielectric Elastomer Actuators (DEAs) are a type of smart material described as compliant capacitors. They show impressive performances as soft actuators, such as a high strain and fast response. Nonetheless, replicating natural muscle function with DEAs h ...
Society of Photo-Optical Instrumentation Engineers (SPIE)2024

Beam homogeneity of caesium seeded SPIDER using a direct beamlet current measurement

The ITER Heating Neutral Beam (HNB) source prototype SPIDER (Source for the Production of Ions of Deuterium Extracted from a Radio frequency plasma), hosted at the Neutral Beam Test Facility (NBTF) in Padova, Italy, has recently started operating with evap ...
ELSEVIER SCIENCE SA2023
Show more
Related MOOCs (22)
Plasma Physics: Introduction
Learn the basics of plasma, one of the fundamental states of matter, and the different types of models used to describe it, including fluid and kinetic.
Plasma Physics: Introduction
Learn the basics of plasma, one of the fundamental states of matter, and the different types of models used to describe it, including fluid and kinetic.
Plasma Physics: Applications
Learn about plasma applications from nuclear fusion powering the sun, to making integrated circuits, to generating electricity.
Show more

Graph Chatbot

Chat with Graph Search

Ask any question about EPFL courses, lectures, exercises, research, news, etc. or try the example questions below.

DISCLAIMER: The Graph Chatbot is not programmed to provide explicit or categorical answers to your questions. Rather, it transforms your questions into API requests that are distributed across the various IT services officially administered by EPFL. Its purpose is solely to collect and recommend relevant references to content that you can explore to help you answer your questions.