Publication

Replicated aluminium foam

Jean-François Despois
2005
EPFL thesis
Abstract

This thesis explores the processing and properties of microcellular aluminium-based materials produced by replication. It includes the development of a pressure infiltration process for net-shape component production, structural characterization of the foams, measurement of their fluid flow permeability and their uniaxial deformation characteristics, together with contributions towards explaining and modeling these properties. Sodium chloride particles are classified and compacted to form an open-pore pattern that is infiltrated with molten pure aluminium under gas pressure. After solidification of the metal, the salt is dissolved in water, yielding an open-cell aluminium foam, the structure of which replicates in negative that of the preform. Resulting highly porous aluminium foams (or "sponges"), regular and homogeneous in pore size, pore shape and density, are produced with an average pore size ranging from 5 to 500 μm and a relative density between 10 and 35 % (corresponding to porosity between 65 and 90 %). The structure of these replicated foams is characterized by optical and scanning electron microscopy. A collaboration with Ms A. Marmottant and Dr. Luc Salvo, GPM2, INP Grenoble, France, allowed three-dimensional images to be produced by X-ray tomography using synchrotron radiation, at the ESRF in Grenoble, France. The Darcian fluid flow permeability of replicated foams is measured varying the average cell size (75 and 400 μm) and the relative density (from 12 to 32 %). Data show the expected dependence on the square of the pore size and agree with other experimental data in the literature for coarser aluminium foams produced by a different casting process. A predictive model for the permeability of open-pore microcellular materials is derived based on a quantitative description of the foam structure, leading to a simple analytical expression. Predictions agree well with present and published experimental data. Mechanical tests are performed in both compression and tension to evaluate the response of pure aluminium replicated foams and its dependence on principal microstructural parameters. Present and published experimental data for the stiffness and the flow stress are compared with the usual Gibson-Ashby equations and with predictions of mean-field models for the deformation of composite materials adapted to metal foams. The best predictor of the behaviour of replicated foams is found with the differential effective medium calculation of composite elastic moduli. This, coupled with the modified secant modulus model of composite non-linear deformation by Suquet is also shown to provide a good predictor of the plastic flow characteristics of these foams. Damage accumulation during foam deformation is evidenced, lowering the foam stress in both tension and compression and causing an evolution in foam stiffness and electrical conductance. In-situ compression and tension tests are performed to observe by X-ray microtomography the mechanisms of deformation and fracture at the foam cell scale. The formation of plastic hinges in compression and strut necking and fracture in tension are evidenced. Damage is shown to govern the tensile failure of the foams, in accordance with theory. The influence of microstructural features on the mechanical behaviour of replicated aluminium foams is investigated. It is shown in particular that the average pore size of the foams influences their plastic flow stress and work hardening rate, both increasing with decreasing pore size. Variations in the heat treatment of the foams are used to show that this plasticity size effect is dislocational in nature, and that it has its origin in dislocation emission during thermal excursions of the Al/NaCl precursor of the foam, before dissolution of the salt. The infiltration pressure and the salt grain shape are also shown to influence the foam structure and the foam uniaxial compressive mechanical response.

About this result
This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.
Related concepts (34)
Metal foam
In materials science, a metal foam is a material or structure consisting of a solid metal (frequently aluminium) with gas-filled pores comprising a large portion of the volume. The pores can be sealed (closed-cell foam) or interconnected (open-cell foam). The defining characteristic of metal foams is a high porosity: typically only 5–25% of the volume is the base metal. The strength of the material is due to the square–cube law. Metal foams typically retain some physical properties of their base material.
Plasticity (physics)
In physics and materials science, plasticity (also known as plastic deformation) is the ability of a solid material to undergo permanent deformation, a non-reversible change of shape in response to applied forces. For example, a solid piece of metal being bent or pounded into a new shape displays plasticity as permanent changes occur within the material itself. In engineering, the transition from elastic behavior to plastic behavior is known as yielding. Plastic deformation is observed in most materials, particularly metals, soils, rocks, concrete, and foams.
Foam
Foams are materials formed by trapping pockets of gas in a liquid or solid. A bath sponge and the head on a glass of beer are examples of foams. In most foams, the volume of gas is large, with thin films of liquid or solid separating the regions of gas. Soap foams are also known as suds. Solid foams can be closed-cell or open-cell. In closed-cell foam, the gas forms discrete pockets, each completely surrounded by the solid material. In open-cell foam, gas pockets connect to each other.
Show more
Related publications (58)

Bringing casting to microfabrication: processing and deformation of microcastings

Luciano Borasi

This work extends the range of pathways for the production of metallic microcomponents by downscaling metal casting. This is accomplished by using either of two different molding techniques, namely femtosecond laser micromachining or lithographic silicon m ...
EPFL2023

3-D contact and pore network analysis of MICP cemented sands

Dimitrios Terzis, Nimisha Roy

The study describes a comprehensive methodology to evaluate X-Ray micro-computed tomography data from sand samples and to characterize their 3D microstructural properties. Fine and medium-grained sands are analyzed in their natural and bio-cemented states. ...
SPRINGER2023

Dynamic study of contact damping in martensitic stainless steels using nano-indentation

Philippe Spätig, Hans-Peter Seifert

The study was undertaken to gain insight into the micro-mechanisms controlling plasticity at the micrometer scale of elastic-plastic metallic alloys. Dynamic nano-indentation tests, where a small harmonic force amplitude is superimposed during loading, ref ...
ELSEVIER2020
Show more
Related MOOCs (11)
Sorption and transport in cementitious materials
Learn how to study and improve the durability of cementitious materials.
Synchrotrons and X-Ray Free Electron Lasers (part 1)
Synchrotrons and X-Ray Free Electron Lasers (part 1)
Synchrotrons and X-Ray Free Electron Lasers (part 2)
The first MOOC to provide an extensive introduction to synchrotron and XFEL facilities and associated techniques and applications.
Show more