Mechanical and microstructural characteristics of Ti6Al4V/AA2519 and Ti6Al4V/AA1050/AA2519 laminates manufactured by explosive welding

Related publications (28)

Page 3 of 3

About
Privacy
Disclaimer

Graph Chatbot

Scanning Small-Angle X-ray Scattering of Injection-Molded Polymers: Anisotropic Structure and Mechanical Properties of Low-Density Polyethylene

Marianne Liebi, Manuel Guizar Sicairos

Injection molding is known to create a layered anisotropicmorphologyacross the sample thickness due to varying shear and cooling ratesduring the manufacturing process. In this study, scanning small-angleX-ray scattering was used to visualize and quantify t ...

AMER CHEMICAL SOC2023

Quantitative study of the thickness-dependent stress in indium tin oxide thin films

Varun Gupta

A quantitative analysis of stress in indium tin oxide (ITO) films with varying thicknesses was conducted using high-precision stylus profilometry. The experimental results revealed a transition of the stress type from tensile to compressive as the ITO film ...

Elsevier Science Sa2023

Highly Efficient and Air-Stable Inorganic Perovskite Solar Cells Enabled by Polylactic Acid Modification

Yong Ding, Feng Liu

Inorganic perovskite solar cells (PSCs) suffer from serious carrier recombination and open-circuit voltage loss because of surface defects and unfavorable energy level alignment. Herein, a polylactic acid (PLA) modification approach to improve the performa ...

WILEY-V C H VERLAG GMBH2023

Tunnel junction sensing of TATP explosive at the single-molecule level

Helena Miljkovic, Radomir Zikic

Triacetone triperoxide (TATP) is a highly potent homemade explosive commonly used in terrorist attacks. Its detection poses a significant challenge due to its volatility, and the lack of portability of current sensing techniques. To address this issue, we ...

Royal Soc Chemistry2023

Processability, microstructure and precipitation of a Zr-modified 2618 aluminium alloy fabricated by laser powder bed fusion

Christian Leinenbach, Xavier Maeder

Additive manufacturing offers the opportunity to produce complex geometries from novel alloys with improved properties. Adapting conventional alloys to the process-specific properties can facilitate rapid implementation of these materials in industrial pra ...

2022

Effect of Y2O3 dispersoids on microstructure and creep properties of Hastelloy X processed by laser powder-bed fusion

Christian Leinenbach

Laser powder bed fusion (LPBF) was used to consolidate powders of a Ni-Cr-Fe-Mo alloy (Hastelloy X) blended with 1 wt% Y2O3 nanometric powders. The nearly-dense, crack-free specimens, with and without oxide dispersion strengthening (ODS), exhibit high-aspe ...

ELSEVIER2022

Weakening effect of various pore fluids on the tensile strength of granite

Guanyi Lu

Laboratory three-point bending experiments are carried out to evaluate the effect of various fluids on the tensile strength of granite. The granite specimens were tested under both dry and saturated conditions. The fluids used to saturate the granite inclu ...

SPRINGER HEIDELBERG2022

Machine learning for metallurgy IV: A neural network potential for Al-Cu-Mg and Al-Cu-Mg-Zn

William Curtin, Daniel John Gilles Marchand

Most metallurgical properties, e.g., dislocation propagation, precipitate formation, can only be fully understood atomistically but most phenomena and quantities of interest cannot be measured experimentally. Accurate simulation methods are essential but f ...

2022

Page 3 of 3

Scanning Small-Angle X-ray Scattering of Injection-Molded Polymers: Anisotropic Structure and Mechanical Properties of Low-Density Polyethylene

Marianne Liebi, Manuel Guizar Sicairos

AMER CHEMICAL SOC2023

Processability, microstructure and precipitation of a Zr-modified 2618 aluminium alloy fabricated by laser powder bed fusion

Christian Leinenbach, Xavier Maeder

2022

Highly Efficient and Air-Stable Inorganic Perovskite Solar Cells Enabled by Polylactic Acid Modification

Yong Ding, Feng Liu

WILEY-V C H VERLAG GMBH2023

Machine learning for metallurgy IV: A neural network potential for Al-Cu-Mg and Al-Cu-Mg-Zn

William Curtin, Daniel John Gilles Marchand

2022