Publication

Robust PECVD SiC membrane made for stencil lithography

Related publications (28)

Functionalized Å-scale Pores in Graphene for Carbon Capture

Single-layer graphene, hosting a high density of functionalized molecular-sieving atom-thick pores, is considered to be an excellent material for gas separation membranes. These functionalized atom-thick pores enable the shortest transport pathway across t ...

EPFL2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Tara Habibi, Landolf-Giosef-Anastasios Rhode-Barbarigos

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

From Surfactants to 3D Printing: How Ion-Chelator Pair Interactions Affect the Mechanical Properties of Bioinspired Materials

Gaia De Angelis

The remarkable adaptability observed in marine ecosystems has often inspired researchers when developing new soft materials. The research undertaken in this thesis explores how ion chelator pair interactions influence the mechanical properties of bioinspir ...

EPFL2024

Towards Scalable Electronics: Synthetic 2D Materials for Large-Area 2D Circuit Integration

Zhenyu Wang

In the past decades, a significant increase of the transistor density on a chip has led to exponential growth in computational power driven by Moore's law. To overcome the bottleneck of traditional von-Neumann architecture in computational efficiency, effo ...

EPFL2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Influence of micro-patterned support properties and interfacial polymerization conditions on performance of patterned thin-film composite membranes

Kumar Varoon Agrawal, Cédric Karel J Van Goethem

Patterned membranes prepared via spray-modified non -solvent induced phase separation (s-NIPS) have successfully shown enhanced fluxes and better fouling control, thanks to the increased surface area and high fluid shear at the membrane/feed interface. The ...

Elsevier2024

Membrane electrode assembly simulation of anion exchange membrane water electrolysis

Jan Van Herle, Suhas Nuggehalli Sampathkumar, Khaled Lawand, Zoé Mury

Anion exchange membrane water electrolysis (AEMWE) offers a green hydrogen production method that eliminates the need for platinum group metals (PGM) as electrocatalysts. This study employs a COMSOL (R) 6.0 model to simulate a 1x1 cm(2) Ni fibre - Raney (R ...

Elsevier2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Strain engineering and strain measurement by spring tethers on suspended epitaxial GaN-on-Si photonic crystal devices

Romuald Houdré, Jun Wang

Suspended epitaxial gallium nitride (GaN) on silicon (Si) photonic crystal devices suffer from large residual tensile strain, especially for long waveguides, because fine structures tend to crack due to large stress. By introducing spring-like tethers, des ...

Iop Publishing Ltd2024