Publications associées à Thermoplastique

Moulding and Microfluidic Wet Spinning of the Soft Polymer Optical Fibers for Sensory Applications

Polymer optical fibre (POFs) based wearable sensors have attracted a lot of attention in the field of healthcare and biomedical applications. They are in particular envision as the next generation of sensors for the continuous, real-time n ...

EPFL2024

Near-Room-Temperature Detection of Aromatic Compounds with Inkjet-Printed Plasticized Polymer Composites

Jürgen Brugger, Thomas Maeder, Mohammadmahdi Kiaee

Chemiresistive gas sensors composed of a thermoplastic polymer matrix and conductive fillers offer various advantages for detecting volatile organic compounds (VOCs), including low power consumption due to near-room-temperature operation, high sensitivity, ...

Amer Chemical Soc2024

Thermo-hydro-mechanical behaviour of the Callovo-Oxfordian claystone under thermal changes

Héloïse Manon Fuselier

Underground storage of radioactive waste is consensually recognised as the safest storage solution by European and worldwide countries relying mainly or partially on nuclear energy production. Over twenty years of research led by the French national agency ...

EPFL2024

Influence of the molecular weight and physical properties of a thermoplastic polymer on its dynamic wetting behavior

Valentin Rougier

The wetting dynamics of molten thermoplastic polymers, which are known to influence the force balance of the triple line, are not understood properly despite their importance in many industrial processes. In particular, the influence of the molecular weigh ...

Elsevier2023

A novel interfacial polymerization assisted phase inversion process for the facile fabrication of ion-selective nanofiltration membranes

Zongyao Zhou, Tao Liu, Shijie Hu

Interfacial polymerization (IP) and non-solvent induced phase inversion (NIPS) are the two most commonly used mainstream technologies to fabricate separation membranes. Taking their advantages, we developed a simple, facile and scalable method to integrate ...

Elsevier Science Sa2023

Simultaneous local sensing of two chemical properties with dual soft probe scanning electrochemical microscopy

Hubert Girault, Andreas Stephan Lesch, Gregorio Bonazza

A new method for the rapid and economic fabrication of dual soft microelectrodes for Soft-Probe-Scanning electrochemical microscopy (Soft-Probe-SECM) and their use for the simultaneous local detection of locally generated species is presented. The process ...

PERGAMON-ELSEVIER SCIENCE LTD2023

Highly Efficient and Air-Stable Inorganic Perovskite Solar Cells Enabled by Polylactic Acid Modification

Yong Ding, Feng Liu

Inorganic perovskite solar cells (PSCs) suffer from serious carrier recombination and open-circuit voltage loss because of surface defects and unfavorable energy level alignment. Herein, a polylactic acid (PLA) modification approach to improve the performa ...

WILEY-V C H VERLAG GMBH2023

Additive and digital manufacturing of transient sensors and bioelectronics

Nicolas Francis Fumeaux

Transient electronics have emerged as a promising class of devices, capable of breaking down without harmful side effects to their environment. They have tremendous potential as bioresorbable electronics for temporary applications in the human body, and as ...

EPFL2023

Novel tooling for direct melt impregnation of textile with variotherm injection moulding: Methodology and proof of concept

Véronique Michaud, Vincent Werlen, Christian Rytka

Thermoplastic compression resin transfer moulding coupled with injection moulding is an appealing process for the production of thermoplastic composites. However, its implementation at an industrial scale remains challenging as variotherm injection mouldin ...

SAGE PUBLICATIONS LTD2022

A life cycle analysis of novel lightweight composite processes: Reducing the environmental footprint of automotive structures

Véronique Michaud, Baris Çaglar, Colin Gomez, Vincent Werlen, Christian Rytka

In this study, three novel thermoplastic impregnation processes were analyzed towards automotive applications. The first process is thermoplastic compression resin transfer molding in which a glass fiber mat is impregnated in through thickness by a thermop ...

ELSEVIER SCI LTD2022