Antenne radioélectrique | EPFL Graph Search

thumb|Antenne rideau HF de télécommunication. thumb|Antennes de réception de la télévision. thumb|Montage d'une antenne de station terrienne au Nicaragua. thumb|upright=1.8|Un diagramme animé d'une antenne dipôle recevant une onde radio. En radioélectricité, une antenne est un dispositif permettant de rayonner (émetteur) ou de capter (récepteur) les ondes électromagnétiques. L'antenne est un élément fondamental dans un système radioélectrique, et ses caractéristiques de rendement, gain, diagramme de rayonnement influencent directement les performances de qualité et de portée du système. Cet article définit les caractéristiques et paramètres généraux des antennes, chaque antenne et application particulière étant développée dans les articles liés. Historique Heinrich Hertz utilisa pour la première fois, en 1888, des antennes pour démontrer l'existence des ondes électromagnétiques prédites par la théorie de Maxwell. Il utilisa des antennes doublet, tant pour la réception que

A portable picocell antenna for 5G

Danelys Rodríguez Avila

Deployable emergency communication systems are a backbone solution for replacing damaged network infrastructures and/or providing high-end services in case of an emergency event. It is important that such systems are up-to-date with the latest mobile network technology, for enabling connectivity to users and profiting from its enhanced capabilities. The advent of 5G promises higher data rates, lower latencies and improved quality of services when compared to previous generations. To achieve that, mm-Waves have been identified as a key element due to the wide available spectrum. The implementation of deployable emergency communication systems compatible with 5G mm-Waves technologies, thus benefiting from its prospective advantages, is of great interest. This thesis focuses on 5G mm-Waves antenna design for this kind of applications. The high network capacity demand, the unfavourable channel conditions at mm-Waves and the still underdeveloped related radio frequency (RF) technology define a group of challenging requirements on the antenna design. While directive antennas are required to mitigate the attenuation with distance at these bands, omnidirectional coverage still needs to be provided. In addition, wide bandwidth operation, high efficiency, and low cost and power consumption are desired. In this context, antennas with multibeam forming capabilities have been widely acknowledged as a key enabling technology to support 5G wireless communications, representing an attractive solution to provide omnidirectional coverage while supporting Multiple Input Multiple Output (MIMO) techniques. In this thesis, the design and implementation of a broadband efficient multibeam antenna for a portable picocell station are investigated. The picocell scenario in the context of emergency communications is studied and the antenna link budget is calculated considering mm-Waves propagation properties and available information on the upcoming standard. This leads to the definition of the design requirements and a preliminary antenna architecture that consists of an MxN antenna fed by a hybrid beamforming network (HBFN). This architecture is a promising approach for making multibeam antennas cost- and energy-efficient according to the latest research. The synthesis of the HBFN was realized considering the design constraints in elevation and azimuth such that the subarray, fed by an analog beamforming network, provides a csc2 pattern shape in elevation while M subarrays are controlled by a digital beamforming network to generate multiple orthogonal beams in azimuth. The antenna subarray was designed, fabricated and measured. Based on this, a study of the antenna array beamsteering capabilities in azimuth was carried out. After investigating the main parameters involved in improving its performance, the subarray design was optimized accordingly. The proposed antenna consists in a 12x6 array that works at 26 GHz with an impedance bandwidth higher than 12%. The radiation pattern shape in elevation is preserved over 7.3% of bandwidth. The antenna gain is superior to 10 dBi along the band of interest with a maximum value of 15 dBi. Simulated and measured results were compared, and the antenna beamsteering performance was tested for different sets of constraints indicating promising capabilities for a wide range of deployment scenarios. The proposed and validated design meets the requirements of the targeted applications on a practical low-profile implementation.

EPFL2021

Effect of intelligent antennas on radio system planning and on mitigation

Juliane Iten Chaves Simoes

Smart antennas have been recently applied to improve the capacity and the performance of second generation wireless mobile communication systems. In general, smart antennas reduce the effects of multipath fading and improve the signal-to-noise-plus-interference ratio (SNIR). Additional advantages such as channel capacity increase in urban areas, coverage extension in urban areas and spectrum efficiency in general can be obtained with the aid of smart antennas at the base station. Drawbacks are the cost, and both hardware and software complexity. Smart antennas promise a clear advantage in multi-service traffic scenario in comparison with non-adaptive antenna techniques. It is generally accepted that the adaptive antennas technique will be a key enable for the success of the European third generation mobile communication system known as Universal Mobile Telecommunication System (UMTS). The first part of this thesis presents two types of smart antenna systems: switched beam antennas and adaptive arrays. It introduces statistical models for them and investigates the performance measures of cellular radio systems with and without smart antennas deployed at base stations. Employing Monte-Carlo methodology, a tool has been developed to analyze the interference between two different systems that share the same geographical area and have neighboring frequency channels. The statistical smart antennas model has been used to verify the mitigation of the interference compared with others antennas used at the base station. These simulations have been done for TDMA, FDMA and CDMA systems. Wireless communication operating at different frequencies on the non-ionizing radiation (NIR) region of the electromagnetic spectrum has greatly increased in the last few decades, with important benefits for the population. These include mobile communication, such as cellular telephone systems. However, the radiated electromagnetic field levels increased substantially in areas where people may stay during long periods each day. This may result in long-term exposure to the population. International guidelines and standards were developed aiming at protecting the population, and limiting the maximum radiation produced. The methods used by regulation authorities to evaluate the field levels at places of sensitive use yield very conservative results. They need thus to be refined prior to the introduction of adaptive antennas. In the second part of the thesis, a 3D ray tracing tool is developed to predict the propagation for real scenarios using UMTS systems. This tool takes into account 3D radiation diagrams and multipath propagation. It was used in real scenarios to compare the real field levels with the levels obtained by the approximate methods defined by the regulation standards. Finally, this tool was used to predict the field levels in a scenario containing smart antennas. Scenario not foreseen in the method described in the standards.

EPFL2008

Wideband Cavity-Backed CubeSat Antenna in S band

Anja Skrivervik Favre, Miroslav Veljovic

The Telemetry, Tracking and Command (TT&C) antennas are a crucial component of small satellites, as their in-orbit attitude is not always well-defined. The TT&C antenna design for a CubeSat is an even more challenging task, considering the volume restrictions imposed by the standard, and the bandwidth requirements for a duplex communication. A detailed design process of a low profile S-band antenna, suitable for CubeSat applications, is presented in this paper. The fabricated prototype exhibits a 10-dB impedance bandwidth of 40%, and a 3-dB AR-bandwidth of 32%.

The European Association on Antennas and Propagation (EurAAP)2018