Publications associées à Austenitic stainless steel

Plasmoid drift and first wall heat deposition during ITER H-mode dual-SPIs in JOREK simulations

The heat flux mitigation during the thermal quench (TQ) by the shattered pellet injection (SPI) is one of the major elements of disruption mitigation strategy for ITER. It's efficiency greatly depends on the SPI and the target plasma parameters, and is ult ...

IOP Publishing Ltd2024

Control of intermetallics in the interface in directed energy deposition of titanium on stainless steel 316L

Di Cui

Application of a single metal or alloy is often restricted by its properties from optimal combination of performance and cost. Therefore, there is a vast need of joining dissimilar metals for various applications in biomedical, aerospace, automobile and ma ...

EPFL2023

Towards Robust Monitoring of the Laser Powder Bed Fusion Process based on Acoustic Emission combined with Machine Learning Solutions

Rita Drissi Daoudi

Laser Powder Bed Fusion (LPBF) is an Additive Manufacturing (AM) process consolidating parts layer by layer, from a metallic powder bed. It allows no limitation in terms of geometry and is therefore of particular interest to various industries. Metallic LP ...

EPFL2023

Microscopic Digital Image Correlation Analysis of Strain Distributions in Stainless Steel 316L Induced by Multiaxial Cyclic Loading

Elif Cansu Kursun

Fatigue damage in materials results in localized strain at the microstructural level. In many engineering components of the cooling circuits of nuclear power plants, where austenitic steels are used, the material experiences multiaxial cyclic loading, eith ...

EPFL2023

Tailored deformation behavior of 304L stainless steel through control of the crystallographic texture with laser-powder bed fusion

Roland Logé, Christian Leinenbach, Markus Strobl, Efthymios Polatidis

Laser-powder bed fusion (L-PBF) has gained significant research interest, not only for its profound advantage of producing near-net shape complex geometries of metallic parts, but also for the possibility of producing tailored microstructures. Here we expl ...

ELSEVIER SCI LTD2022

Role of mean stress on fatigue behavior of a 316L austenitic stainless steel in LWR and air environments

Philippe Spätig, Hans-Peter Seifert

Mean stress effects on fatigue life of a stainless steel in air and boiling water reactor (BWR) environments were evaluated by load-controlled tests. In stress-life, non-zero mean stresses increase life in low cycle fatigue regime in both environments and ...

ELSEVIER SCI LTD2021

APT/TEM characterization of the element segregation in ferritic/martensitic steels after irradiation in SINQ

Lijuan Cui

Ferritic /martensitic (FM) steels are among the most important materials in various nuclear applications. As radiation-induced segregation (RIS) is one of the major factors for embrittlement of nuclear materials, thereofre it is essential to study the RIS ...

EPFL2021

A comparative surface analysis of explanted hip joint prostheses made of different biomedical alloys

Stefano Mischler, Angela Bermudez Castañeda, Adriana Esguerra Arce, Johanna Esguerra Arce

The introduction of modular design in total hip arthroplasty has enabled the use of different materials in one single configuration and the adjustment of the prosthesis to the patient's body, and facilitated medical revisions. However, modularity leads to ...

IMPRENTA UNIV ANTIOQUIA2021

Enhancement of riveted steel bridges by adding a trough in UHPFRC acting in composite action

Eugen Brühwiler

Riveted railway bridges are commonly considered as being “old”, having fatigue damage and are therefore replaced. While this practice should be by now obsolete by using novel engineering methods like structural monitoring, prolongation of the service durat ...

Taylor & Francis2021

Understanding Thermomechanical Treatments Induced by Laser Powder Bed Fusion Process

Hossein Ghasemi Tabasi

Additive Manufacturing (AM) is referred to technologies that produce directly 3D parts in a layer-by-layer fashion. Laser Powder Bed Fusion (L-PBF) is one of the most important AM processes, enabling production of very complex metallic objects from a compu ...

EPFL2021