Publications associées à Détendeur thermostatique

DIET Controller: Dynamic Indoor Environment using Deep Reinforcement Learning

Heating, Ventilation, and Air Conditioning (HVAC) Systems utilize much energy, accounting for 40% of total building energy use. The temperatures in buildings are commonly held within narrow limits, leading to higher energy use. Measurements from office bui ...

EPFL2023

Microchannel cooling for the LHCb VELO Upgrade I

Alessandro Mapelli, Giulia Romagnoli, Victor Coco

The LHCb VELO Upgrade I, currently being installed for the 2022 start of LHC Run 3, uses silicon microchannel coolers with internally circulating bi-phase CO2 for thermal control of hybrid pixel modules operating in vacuum. This is the largest scale applic ...

ELSEVIER2022

Hybrid Two-Phase Cooling Technology For Next-Generation Servers: Thermal Performance Analysis

John Richard Thome, Jackson Braz Marcinichen, Filippo Cataldo, Raffaele Luca Amalfi

This paper advances the work presented at ITHERM 2020 where a novel passive two-phase technology was introduced for more efficient cooling of datacenters compared to air-based cooling solutions (e.g. In-Room, In-Row, etc.). The proposed hybrid two-phase co ...

IEEE2021

System for co2 capture from internal combustion engine

François Maréchal, Shivom Sharma

System (2) for CO2 capture from a combustion engine (1) comprising an exhaust gas flow circuit (6) having an inlet end fluidly connected to an exhaust of the combustion engine, a heat exchanger circuit (12), a primary exhaust gas heat exchanger (H1) for tr ...

2020

Investigation of femtosecond laser-tuned thermomechanical properties of fused silica

Pieter Vlugter

The thermomechanical properties of materials are among the most important properties for designing precision instruments, in particular for devices seeking high-dimensional stability, invariant temperature-elastic properties or low thermoelastic losses. De ...

EPFL2020

Experimental Performance of Completely Passive Single and Recirculating Loop Thermosyphon Cooling Systems using Low GWP R1234ze and R1234yf

John Richard Thome

This paper proposes a novel concept for a loop thermosyphon cooling system, designed for the transistor module of a transformer. The thermosyphon uses a free convection cooled condenser, making the system completely passive, i.e. no energy consumption is n ...

IEEE2019

Thermal Engineering of Metal-Organic Frameworks for Adsorption Applications: A Molecular Simulation Perspective

Venkat Kapil

Thermal engineering of metal-organic frameworks for adsorption-based applications is very topical in view of their industrial potential, in particular, since heat management and thermal stability have been identified as important obstacles. Hence, a fundam ...

AMER CHEMICAL SOC2019

Multi-objective optimization of turbo-ORC systems for waste heat recovery on passenger car engines

Jürg Alexander Schiffmann, Kévin Rosset, Eliott Philippe Guenat, Violette Mounier

Waste heat recovery from passenger car internal combustion engines by means of an organic Rankine cycle (ORC) system is promising for reducing CO2 emissions. In this study, different cycle configurations capable of converting waste heat from both coolant a ...

2018

Small, High-Speed, Oil-Free Radial Turbo-compressors for Cooling Applications: Refrigerant Selection

Jürg Alexander Schiffmann

Emerging energy-efficient, oil-free radial centrifugal compressors seem promising for small to mid-capacity air conditioning and refrigeration applications. Compressor design must balance trade-offs among impeller diameter, bearing type, and refrigerant se ...

2018

An updated three-zone heat transfer model for slug flow boiling in microchannels

John Richard Thome, Mirco Magnini

This work proposes a novel physics-based model for the fluid mechanics and heat transfer associated with slug flow boiling in horizontal circular microchannels to update the widely used three-zone model of Thome et al. (2004). The heat transfer model has a ...

Pergamon-Elsevier Science Ltd2017