Publications associées à Contreplaqué

Investigation of mycelium film as the adhesive for poplar veneer bonding: insight into interfacial bonding mechanisms

The emergence of mycelium-bonded biocomposites has been stimulated in the quest for sustainable development. These biocomposites exhibit enhanced mechanical properties through hot pressing, with mycelium playing a crucial role as both the adhesive and rein ...

Taylor & Francis Ltd2024

Experimental characterization and stochastic models for time-dependent rupture of thin-ply composite laminates

Thin-laminate composites with thicknesses below 200 mu m hold significant promise for future, larger, and lighter deployable structures. This paper presents a study of the time-dependent failure behavior of thin carbon-fiber laminates under bending, focusi ...

2024

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

Process development of pre-impregnated hybrid thin-ply composites

Alexios Argyropoulos

Thin-ply composites, obtained with recently developed fiber spreading techniques, rapidly gained industrial interest because they offer a large composite design freedom, and lead to a composite tensile strength that is close to that of the individual fiber ...

EPFL2023

Steel Sheet Sheathed Cold-Formed Steel Framed In-line Wall Systems. I: Impact of Structural Detailing

Fani Derveni

The North American construction industry has seen substantial growth in the use of cold-formed steel (CFS) framing for midrise buildings in recent years. In seismic zones, CFS-framed buildings utilize shear walls to provide the primary lateral resistance t ...

ASCE-AMER SOC CIVIL ENGINEERS2022

Mechanical properties of a balsa wood veneer structural sandwich core material

Thomas Keller, Anastasios Vassilopoulos, Niloufar Vahedi

Balsa wood is an appropriate core material for structural sandwich applications due to its high strength- and stiffness-to-weight ratios. However, the mechanical properties vary considerably owing to the inherent scattering of natural wood materials. One a ...

2020

Improving delamination resistance through tailored defects

John Botsis

Delamination is a well-known damage mode exhibited by laminated composites which has been extensively studied in unidirectional laminates (UD). In this work, a novel strategy consisting of the introduction of a small interlaminar defect to enhance the frac ...

2020

Thermomechanical characterization of a balsa-wood-veneer structural sandwich core material at elevated temperatures

Thomas Keller, Anastasios Vassilopoulos, Chao Wu, Niloufar Vahedi

The tensile, compressive and shear behavior of standardized specimens cut from a veneered balsa wood used as structural sandwich core was investigated at ambient temperatures of up to 250 degrees C. The average moisture content was 9.1%. The specimens' res ...

ELSEVIER SCI LTD2020

Experiments and numerical modelling on angle-ply laminates under remote mode II loading

John Botsis, Georgios Pappas, Charlie Joseph Simon Blondeau

Delamination is a very frequent damage mechanism that affects the integrity of laminated composites. In this study, the effect of ply orientation on crack growth resistance was analyzed for three different anti-symmetric interfaces (+/- 30 degrees, +/- 45 ...

ELSEVIER SCI LTD2020

Transverse cracking in the bulk and at the free edge of thin-ply composites: experiments and multiscale modelling

John Botsis, Robin Amacher, Joël Cugnoni, Sébastien Kohler

Thin-ply composites were shown to exhibit significantly delayed transverse cracking, but the linear onset of damage scaling with ply thickness reported by Amacher et al. (2014) did not correspond to the established LEFM based in situ strength model. This s ...

2019