Publications de John Botsis | EPFL Graph Search

A functional approach towards the design, development, and test of an affordable dynamic prosthetic foot

Kamiar Aminian, Véronique Michaud, John Botsis, Klaus Benedikt Schönenberger, Joël Cugnoni, Mathieu Pascal Falbriard, Rajasundar Chandran

Humanitarian actors involved in physical rehabilitation, such as the International Committee of the Red Cross (ICRC), usually provide their beneficiaries with lower-limb prostheses comprising Solid Ankle Cushion Heel (SACH) feet as these are considered app ...

PUBLIC LIBRARY SCIENCE2022

Monitoring of Torque Induced Strain in Composite Shafts with Embedded and Surface-Mounted Optical Fiber Bragg Gratings

John Botsis, Georgios Violakis, Georgios Pappas

In this study, silica glass, optical fiber Bragg gratings (FBGs) are used for torque-induced strain monitoring in carbon fiber reinforced polymer (CFRP) hollow shafts toward the development of a methodology for structural load monitoring. Optical fibers wi ...

2021

Crack propagation in CFRP laminates under mode I monotonic and fatigue loads: A methodological study

John Botsis, Georgios Pappas, Charlie Joseph Simon Blondeau

Delamination in composite materials is often accompanied by fiber bridging that increases resistance to crack growth. Here, delamination of two unidirectional carbon/epoxy systems was studied under monotonic and displacement-controlled fatigue loading. One ...

ELSEVIER SCI LTD2021

Variations on R-curves and traction-separation relations in DCB specimens loaded under end opening forces or pure moments

John Botsis, Georgios Pappas

In this work the differences in R-curve response and traction-separation relations due to a finite damage zone or large-scale bridging (LSB) in mode I fracture on double cantilever beams (DCB) were investigated under end opening forces (EOF) and pure momen ...

PERGAMON-ELSEVIER SCIENCE LTD2020

Experiments and numerical modelling on angle-ply laminates under remote mode II loading

John Botsis, Georgios Pappas, Charlie Joseph Simon Blondeau

Delamination is a very frequent damage mechanism that affects the integrity of laminated composites. In this study, the effect of ply orientation on crack growth resistance was analyzed for three different anti-symmetric interfaces (+/- 30 degrees, +/- 45 ...

ELSEVIER SCI LTD2020

Towards a geometry independent traction-separation and angle relation due to large scale bridging in DCB configuration

John Botsis, Georgios Pappas

Traction-separation relations due to large scale bridging in composites are very important in modeling their fracture response. Several works demonstrated that such relations are dependent upon the specimen's stiffness and loading conditions. Experimental ...

ELSEVIER SCI LTD2020

Mixed-mode fracture response of anti-symmetric laminates: Experiments and modelling

John Botsis

Multidirectional laminates are very often used in advanced structures. However, the existing data in the literature regarding their fracture response is not conclusive. In this work, the fracture response of a +45 degrees// -45 degrees interface is investi ...

ELSEVIER SCI LTD2020

Improving delamination resistance through tailored defects

John Botsis

Delamination is a well-known damage mode exhibited by laminated composites which has been extensively studied in unidirectional laminates (UD). In this work, a novel strategy consisting of the introduction of a small interlaminar defect to enhance the frac ...

2020

Transverse cracking in the bulk and at the free edge of thin-ply composites: experiments and multiscale modelling

John Botsis, Robin Amacher, Joël Cugnoni, Sébastien Kohler

Thin-ply composites were shown to exhibit significantly delayed transverse cracking, but the linear onset of damage scaling with ply thickness reported by Amacher et al. (2014) did not correspond to the established LEFM based in situ strength model. This s ...

2019

Design optimization of a CFRP-aluminum joint for a bioengineering application

John Botsis, Georgios Pappas

Lightweight design demands and complexity requirements of modern high-end structures in aerospace, automotive, sports and bioengineering can be successfully covered by a combination of fiber reinforced polymers (FRPs) with metallic components. Conventional ...

2019