In situ strain and temperature monitoring of adaptive composite material

An optical fiber sensor is designed to simultaneously measure strain and temperature in an adaptive composite material. The sensor is formed by splicing two fiber Bragg gratings (FBGs) close to each other, which are written in optical fibers with different core dopants and concentrations. Their temperature sensitivities are hence different. The sensor is tested on an adaptive composite laminate made of unidirectional Kevlar-epoxy prepreg plies. Several 150 μm diameter prestrained NiTiCu shape memory alloy (SMA) wires are embedded in the composite laminate together with one fiber sensor. Simultaneous monitoring of strain and temperature during the curing process and activation in an oven is demonstrated

In-situ simultaneous strain and temperature measurement of adaptive composite materials using a fiber Bragg grating based sensor

Hans Georg Limberger, Jan-Anders Månson, Véronique Michaud, René Salathé, Hyungjune Yoon

An optical fiber sensor to simultaneously measure strain and temperature was designed and embedded into an adaptive composite laminate which exhibits a shape change upon thermal activation. The sensor is formed by two fiber Bragg gratings, which are written in optical fibers with different core dopants. The two gratings were spliced close to each other and a sensing element resulted with Bragg gratings of similar strain sensitivity but different response to temperature. This is due to the dependence of the fiber thermo-optic coefficient on core dopants and relative concentrations. The sensor was tested on an adaptive composite laminate made of unidirectional Kevlar-epoxy pre-preg plies. Several 150 mu m diameter pre-strained NiTiCu shape memory alloy wires were embedded in the composite laminate together with one fiber sensor. Simultaneous monitoring of strain and temperature during the curing process and activation in an oven was demonstrated.

2005

Construction material monitoring with "optical hair" hygrometers

Pascal Kronenberg

Moisture is an essential parameter in the behaviour of capillary-porous construction materials such as timber and concrete. It affects liquid and gas transport phenomena, chemical and biological degradation processes, mechanical properties and, in the case of concrete, hydration. From a scientific point of view, moisture monitoring is essential in order to improve the understanding of material behaviour. Moisture measurements may increase the predictive accuracy of established material behaviour models. In practice, the increased knowledge of material behaviour improves structural maintenance planning. The main objective of this work is to propose a measurement method for non-destructive, in-depth moisture monitoring of construction materials. In this context, an intrinsic point and an averaging fibre optic relative humidity sensor have been developed and tested. The sensors are based on optical fibres that are coated with a hygroscopically swelling transducer polymer. When wet, the swelling of the coating strains the fibre (analogy with the hair hygrometer). The induced strain is assessed with conventional fibre optic strain sensing techniques such as fibre Bragg gratings and Michelson interferometry. Theoretical and experimental studies lead to a detailed understanding of the influence of humidity and temperature on the steady and transient state sensor behaviour. The sensors have an accurate, linear, reversible and reproducible response to relative humidity between 5 and 95 %RH and between 13 and 60 °C, at least. The sensor response time is in the order of 20 minutes. However, when packaged, the sensor responds slower. The temperature cross-sensitivity of the fibre Bragg grating sensor may be compensated with an additional non-hygroscopic grating, while the Michelson interferometric sensor provides an auto-compensation of temperature effects. Tests in mortar and timber samples demonstrate that the sensors preserve their sensing ability when embedded. These tests have also clarified the multiplexing potential of fibre Bragg gratings for forming a multi-point RH sensor. Multi-point sensors are particularly useful for profile measurements.

EPFL2003

Extreme temperature sensing using Brillouin scattering in optical fibers

Alexandre Fellay

Stimulated Brillouin scattering in silica-based optical fibers may be considered from two different and complementary standpoints. For a physicist, this interaction of light and pressure wave in a material, or equivalently in quantum theory terms between photons and phonons, gives some glimpses of the atomic structure of the solid and of its vibration modes. For an applied engineer, the same phenomenon may be put to good use as a sensing mechanism for distributed measurements, thanks to the dependence of the scattered light on external parameters such as the temperature, the pressure or the strain applied to the fiber. As far as temperature measurements are concerned, Brillouin-based distributed sensors have progressively gained wide recognition as efficient systems, even if their rather high cost still restricts the number of their applications. Yet they are generally used in a relatively narrow temperature range around the usual ambient temperature; in this domain, the frequency of the scattered light increases linearly with the increase in temperature. The extension of this range toward higher (up to 800°C) and lower (down to 1 K) temperature is the main aim of this thesis. In both cases, our measurements on various fiber samples show that the aforementioned linearity does not hold. Most notably, the characteristics of Brillouin scattering at low and very low temperature are strikingly different from those observed under normal conditions; they are directly related to the disordered nature of the silica that constitutes the fiber, what motivates the large place we here devote to the physics of amorphous solids. Despite the observed nonlinearities, our results demonstrate the feasibility of thermometry based on Brillouin scattering over the full investigated temperature range. We can thus swap in the last part of this work the physicist's point of view for that of an engineer and present the setup and the performances of a sensor, or rather of a whole family of sensors we have tested and improved in the course of the last few years; moreover, some real measurement examples are given. Finally, we propose some possibilities of further enhancement, that remain right now at the preliminary stage of their development.

EPFL2003

Extreme temperature sensing using Brillouin scattering in optical fibers

Alexandre Fellay

EPFL2003

Construction material monitoring with "optical hair" hygrometers

Pascal Kronenberg

EPFL2003