Boiling on a Tube Bundle: Part II-Heat Transfer and Pressure Drop

An extensive experimental study was undertaken to measure nucleate pool boiling heat transfer coefficients, local bundle boiling heat transfer coefficients, and two-phase bundle pressure drops for R134a and R236fa on one plain tube bundle configuration. The experimental database allowed the refinement of frictional pressure drop models previously developed at the Laboratory of Heat and Mass Transfer. Together with the new onset of dryout prediction method presented in part I (preceding article in this issue), this constitutes a significant improvement in such prediction methods. The local bundle boiling heat transfer data highlighted the dependency of the heat transfer coefficient on the heat flux as expected for the present conditions. The new method was proposed and worked well versus the present database and was also validated against additional refrigerants from independent studies. It was proven to also work reasonably well for falling film evaporation data, proving the new prediction method is applicable for a wide range of operating conditions.

Heat Management for Process Intensification of Fast Exothermic Reactions in Microstructured Reactors

Julien Haber

Nowadays, the production in fine chemical and pharmaceutical industry is mostly carried out in large scale batch reactors having typically dimensions of a few meters to satisfy the demand of the market. Even though this technology has been widely used and developed for centuries, it is by far not optimal for every type of reaction. For example, when working with exothermic reactions, the produced heat can’t be always fully evacuated. To avoid run-aways, high amounts of solvents are used to increase the heat capacity of the mixture, or semi-batch mode with a slow addition of one of the reactants. In both cases, the space-time yield, i.e. mass of product produced per unit of time and per unit of volume, drastically diminishes. One of the main enabling technologies allowing process intensification are the microstructured devices, characterized by high heat and mass transport rates due to the small characteristic dimensions (< 1mm). Using this type of equipment, almost isothermal conditions can be achieved while carrying out fast exothermic reactions (with characteristic reaction times down to tr ≈ 10 s). Thereby, the target throughput is reached by numbering-up, i.e. parallel connection of several identical microreactors. For very fast exothermic reactions, especially for quasi-instantaneous reactions, dimensions smaller than 100 μm are needed to prevent the formation of unwanted hot spots. As such small dimensions are not suitable for industrial scale due to possible clogging and high pressure drops, other solutions are warranted. The aim of this thesis is to develop alternative microstructured reactors enabling quasi-instantaneous reactions to be carried out under intensified conditions while suppressing the large hot spots. The work is divided into two main parts: determination of suitable strategies for the microstructured reactor design via numerical simulations (Chapter 3) and the experimental validation of the best microstructured reactor concept (Chapter 4-6). Three strategies for enhanced temperature control within microstructured reactors for quasi-instantaneous reactions are taken for analysis using numerical simulation: 1) reduction of hot spot temperature by increased axial heat transfer in the reactor wall, 2) by injection of one reactant in multiple points along the reactor length and 3) by continuous injection of one reactant through a porous wall in a concentric reactor geometry. The multi-injection reactor (option 2) is the most effective design since with an optimized dosing with only 4 injection points the temperature rise is 5-fold smaller as compared to the adiabatic temperature rise. Furthermore, the key design requirements for an efficient multi-injection reactor are identified: 1) complete mixing after each injection and 2) evacuation of the produced heat before reaching the next injection point. To experimentally validate the simulation results, in the subsequent chapter, an experimental method to monitor temperature in microstructured reactors is developed (Chapter 4). To track axial temperature profiles quantitatively, a method based on non-intrusive infrared thermography is developed yielding a resolution of 100 points/mm2 and a precision of 1 °C. In the first validation experiments, the heat transfer coefficient determined in a micro heat exchanger (574 W/m2K) is in good agreement with prior estimations. While carrying out the hydrolysis of tetraethoxysilane as a fast model reaction, incomplete mixing of the reactants is detected via the temperature profile, and is ascribed to the high difference in density of the inlet flows. Applying the method of quantitative IR-thermography to a T-micromixer with circular cross section gives insight into the mixing phenomenon (Chapter 5). The latter is studied via the temperature profile of the reactions strongly controlled by mixing, i.e. dilution of sulfuric acid with water and cyclization of pseudoionone. The mass transfer coefficients determined are in the order of 0.1-9 1/s. It is shown that at high Fourier numbers Fo = tdiff/τ (mixing by shearing), the Damköhler number DaI= τ/tmix remains constant with respect to flow rate at the reactor outlet, as both, mixing time and residence time decrease proportionally with the latter parameter. To enhance the mixing performance, two approaches are applied: 1) the introduction of a carrier phase leading to travelling micro-batches with up to 4-fold faster mixing and 2) the structuring of the channel walls leading to the formation of vortices, and thus, to a substantially improved mixing efficiency. For efficient mixing in the multi-injection reactor (Chapter 6), two types of mixing structures, i.e. the tangential mixer and the herringbone mixer, are developed using low temperature co-fired ceramics, and compared using quantitative infrared thermography. The best mixing performance is obtained by the herringbone structure, providing efficient mixing in a large range of flow rates corresponding to Reynolds numbers Re = 20-130. Finally, a multi-injection reactor comprising three injection points and the herringbone microstructure is developed. Using the quasi-instantaneous and exothermic cyclisation of pseudoionone to α-ionone and β-ionone as model reaction, it is demonstrated that the temperature rise can be reduced 8-fold compared to the adiabatic temperature rise due to 1) the high volumetric heat transfer coefficient in the order of 4·106 W/(m3K), 2) the reduced overall transformation rate due to gradual mixing within the herringbone structure and 3) the injection of pseudoionone at three injection points. Yields of α-ionone and β-ionone above 98 % are achieved at a residence time of 3.7 s while efficiently avoiding the unwanted consecutive polymerization in a temperature range of 30-60 °C. Compared to the conventional semi-batch process, where such high yields can only be attained at temperatures below 10 °C, a 500-fold increased space-time- yield is achieved. In addition to the intensification of the process, the required mass of solvent is halved while maintaining good temperature control, rendering the overall process safe.

EPFL2013

Boiling on a Tube Bundle

Eugene van Rooyen

The complexity of two-phase flow boiling on a tube bundle presents many challenges to the understanding of the physical phenomena taking place. It is important to quantify these numerous heat flow mechanisms in order to better describe the performance of tube bundles as a function of the operational conditions. In the present study, the bundle boiling facility at the Laboratory of Heat and Mass Transfer (LTCM) was modified to obtain high-speed videos to characterise the two-phase regimes and some bubble dynamics of the boiling process. It was then used to measure heat transfer on single tubes and in bundle boiling conditions. Pressure drop measurements were also made during adiabatic and diabatic bundle conditions. New enhanced boiling tubes from Wolverine Tube Inc. (Turbo-B5) and the Wieland-Werke AG (Gewa-B5) were investigated using R134a and R236fa as test fluids. The tests were carried out at saturation temperatures Tsat of 5°C and 15°C, mass flow rates from 4 to 35 kg/m2s and heat fluxes from 15 to 70 kW/m2, typical of actual operating conditions. The flow pattern investigation was conducted using visual observations from a borescope inserted in the middle of the bundle. Measurements of the light attenuation of a laser beam through the intertube two-phase flow and local pressure fluctuations with piezo-electric pressure transducers were also taken to further help in characterising the complex flow. Pressure drop measurements and data reduction procedures were revised and used to develop new, improved frictional pressure drop prediction methods for adiabatic and diabatic two-phase conditions. The physical phenomena governing the enhanced tube evaporation process and their effects on the performance of tube bundles were investigated and insight gained. A new method based on a theoretical analysis of thin film evaporation was used to propose a new correlating parameter. A large new database of local heat transfer coefficients were obtained and then utilised to generate improved prediction methods for pool boiling and bundle boiling, including a method for predicting the onset of dryout.

EPFL2011

Two-phase flow of refrigerants in 85μm-wide multi-microchannels: Part II – Heat transfer with 35 local heaters

Etienne Costa-Patry, Bruno Michel, Jonathan Olivier, John Richard Thome

This article is the second part of a study on flow boiling of R236fa and R245fa. This part presents the heat transfer coefficients obtained in a 12.7 mm silicon evaporator composed of 135 microchannels with 85 mu m wide and 560 mu m high channels separated by 46 mu m wide fins. There were 35 local heaters and temperature measurements arranged in a 5 x 7 array. The heat transfer results were uniform in the lateral direction to the flow (attributable to the inlet restriction) and a function of the heat flux, vapor quality and mass flux. The steady-state standard deviation of the local base temperature was less than 0.2 degrees C, inferring that the boiling process was very stable. For wall heat fluxes over 45 kW/m(2), the heat transfer coefficient curves were V-shaped, decreasing for intermittent flow regimes and increasing for annular flow. The three-zone model of Thome et al. (2004) was the best heat transfer prediction method when setting the dryout thickness equal to the channel roughness. (c) 2011 Elsevier Inc. All rights reserved.