Heat transfer monitoring between quenched high-temperature superconducting coated conductors and liquid nitrogen

High-temperature superconducting coated conductors (HTS-CCs) are good candidates for resistive superconducting fault current limiter (RSFCL) applications. However, the high current density they can carry and their low thermal diffusivity expose them to the risk of thermal instability. In order to find the best compromise between stability and cost, it is important to study the heat transfer between HTS-CCs and the liquid nitrogen (LN2) bath. This paper presents an experimental method to monitor in real-time the temperature of a quenched HTS-CC during a current pulse. The current and the associated voltage are measured, giving a precise knowledge of the amount of energy dissipated in the tape. These values are compared with an adiabatic numerical thermal model which takes into account heat capacity temperature dependence of the stabilizer and substrate. The result is a precise estimation of the heat transfer to the liquid nitrogen bath at each time step. Measurements were taken on a bare tape and have been repeated using increasing Kapton® insulation layers. The different heat exchange regimes can be clearly identified. This experimental method enables us to characterize the recooling process after a quench. Finally, suggestions are done to reduce the temperature increase of the tape, at a rated current and given limitation time, using different thermal insulation thicknesses.

Stability modeling of the LHC Nb-Ti Rutherford cables subjected to beam losses

Luca Bottura, Enrico Felcini

The Large Hadron Collider (LHC) at CERN is being prepared for its full energy exploitation during Run III, i.e. an increase of the beam energy beyond the present 6.5 TeV, targeting the maximum discovery potential attainable. This requires an increase of the operating field of the superconducting dipole and quadrupole magnets, which in turn will result in more demanding working conditions due to a reduction of the operating margin while the energy deposited by particle loss will increase. Beam-induced magnet quenches, i.e. the transition to normal conducting state, will become an increasing concern, because they could affect the availability of the LHC. It is hence very important to understand and be able to predict the quench levels of the main LHC magnets for the required values of current and generated magnetic fields. This information will be used to set accurate operating limits of beam loss, with sufficient but not excessive margin, so to achieve maximal beam delivery to the experiments. In this study we used a one dimensional, multi-strand thermal-electric model to analyze the maximum beam-losses that can be sustained by the LHC magnets, still remaining superconducting. The heat deposition distribution due to the beam losses is given as an input for the stability analysis. Critical elements of the model are the ability to capture heat and current distribution among strands, and heat transfer to the superfluid helium bath. The computational model has been benchmarked against energy densities reconstructed from beam-induced MB (Main Bending) dipole quenches during LHC operation at 6.5 TeV. The model was then used to evaluate the stability margin of both MB and MQ (Main Quadrupole) magnets at different beam energies, up to the expected ultimate operating energy of the LHC, 7.5 TeV. The comparison between the quench levels underlines how the increase of beam energy implies a substantial reduction of magnets stability and will require much stricter setting on the allowable beam losses to avoid resistive transitions during operation.

2019

Can Resistive-Type Fault Current Limiter Operate in Cryogen-Free Environment?

Bertrand Dutoit

Superconducting fault current limiters are unique devices that offer fast response to fault without need of an external triggering system. Therefore, they are interesting for industrial use, although their price is high. The principle of the resistive fault current limiter is based on the steep current-voltage characteristic of superconductors. When the current rises over the critical one, voltage on the superconductor rises steeply, and this mechanism blocks the increase of the current. Simultaneous appearance of voltage and current during this limiting period of operation generates a substantial amount of heat that is dissipated in the superconducting wire causing a rapid increase of its temperature. In this contribution, we further develop the idea that, during a limiting period, there is only a small difference between cooling by liquid nitrogen and adiabatic conditions. Using this approach, one can think about a current limiter free from a liquid coolant using a cryocooler. In this contribution, we discuss main differences in cooling conditions and test the idea on a short sample of the high-temperature superconductor REBCO conductor. We compare the behavior of identical samples cooled to the same temperature by liquid nitrogen and conduction cooled. If the realization can be achieved, the huge benefit would be an FCL with a tunable triggering current via its operating temperature.

Ieee-Inst Electrical Electronics Engineers Inc2016

Fast Hotspot Detection in SFCLs by Exploiting Strain Response in Optical Fiber Sensing

Arooj Akbar, Bertrand Dutoit, Nicolò Riva, Luc Thévenaz, Zhisheng Yang

Superconducting fault current limiters (SFCLs) can be used to limit fault currents in both meshed DC and AC grids by transitioning from superconducting to resistive state, in the presence of high currents. While the device is theoretically a great way to protect grids, the inherent inhomogeneity of critical current along the superconductor length can lead to localized heating, called hotspots, and ultimately destruction of the SFCL device. At EPFL under the European Union project Fastgrid, an extremely efficient Mach-Zehnder interferometer (MZI) based optical fiber sensing technique has been developed and patented that can detect even singular hotspots within 15 ms to protect SFCLs. The MZI response is characterized by a strain sensitive as well as a temperature sensitive contribution. This paper outlines an investigation by means of FEM modeling into the response sensitivity. A 2-D thermal model of the superconducting tape and optical fiber was made to study thermal transfer to the optical fiber from the REBCO tape. The simulation results showed that temperature rise observed in the optical fiber is slower than the MZI response time, proving a strain sensitive response in the experiment measurements. Sound mechanical coupling between the optical fiber and the superconductor tape can enhance strain transfer to the optical fiber and hence reduce hotspot detection time. With this improved performance, the health monitoring for SFCLs can be much more efficient and reliable.

2021

Stability modeling of the LHC Nb-Ti Rutherford cables subjected to beam losses

Luca Bottura, Enrico Felcini

2019