Swelling Behavior and Nanomechanical Properties of (Peptide-Modified) Poly(2-hydroxyethyl methacrylate) and Poly(poly(ethylene glycol) methacrylate) Brushes

Poly(2-hydroxyethyl methacrylate) (PHEMA) and poly(poly(ethylene glycol) methacrylate) (PPEGMA) brushes represent a class of thin, surface-tethered polymer films that have been extensively used e.g. to generate non-biofouling surfaces or as model systems to study fundamental biointerfacial questions related to cell-surface interactions. As the properties of PHEMA and PPEGMA brushes depend on the hydration and swelling of these thin films, it is important to understand the influence of basic structural parameters such as the composition of the polymer brush, the film thickness, or grafting density on these phenomena. This article reports results of a series of experiments that were performed to investigate the swelling behavior and mechanical properties of a diverse library of PHEMA and PPEGMA brushes covering a range of film thicknesses and grafting densities. The swelling ratios of the PHEMA and PPEGMA brushes were determined by ellipsometry and neutron reflectivity experiments and ranged from similar to 1.5 to similar to 5.0. Decreasing the grafting density and decreasing the film thickness generally results in an increase in the swelling ratio. Modification of the PHEMA and PPEGMA brushes with the cell adhesive RGD peptide ligand was found to result in a decrease in the swelling ratio. The neutron reflectivity experiments further revealed that solvated PHEMA and PPEGMA brushes are best described by a two-layer model, consisting of a polymer-rich layer close to the substrate and a second layer that is swollen to a much higher degree at the brush water interface.

Mechanochemically Responsive Surfaces and Soft Tissue Adhesive Interfaces Generated via Controlled Radical Polymerization

Nariye Cavusoglu Ataman

Thin coatings applied to surfaces dramatically improve the properties of materials. Thus, they have found application in a broad variety of areas including biomedicine, nanotechnology, bioelectronics and optics, amongst others. Polymer brushes prepared via surface-initiated controlled radical polymerization (SI-CRP) techniques represent a versatile class of thin polymer coatings that provide manifold opportunities to engineer surface and interface properties. Densely grafted polymer brushes prepared via SI-CRP possess several attractive material properties such as low friction coefficients and the ability to prevent biofouling, which are related to the stretched conformation of the surface tethered polymer chains. Those distinctive characteristics of polymer brushes make them highly appealing to engineer the properties of functional interfaces. A first aim of this Thesis is to investigate the mechanochemistry of hydrophilic polymer brushes prepared via surface-initiated atom transfer radical polymerization (SI-ATRP) from silica substrates. The second aim of the Thesis is to explore poly(2-hydroxyethyl methacrylate) (PHEMA) based polymer brushes as soft-tissue adhesives in wet tissue environment. This Thesis is divided into four chapters, which are briefly summarized below. Chapter 1 provides a summary of recent literature that has reported detachment or degrafting of densely grafted hydrophilic polymer brushes from substrates upon exposure to aqueous media. The collective results from these reports suggest that swelling-induced stretching of hydrophilic polymer brushes lead to mechanochemical activation of the bonds near the brush-substrate interface and subsequently facilitates hydrolytic chain cleavage. Chapter 2 aims to shed light on the influence of two fundamental structural polymer brush parameters on the degrafting of surface-tethered, densely grafted polymer chains, viz. (i) the chemical composition of the ATRP initiator that is used to grow the polymer brushes and (ii) the effect of surface curvature. To this end, a series of poly(poly(ethylene glycol) methacrylate) (PPEGMA) and poly(poly(ethylene glycol) methyl ether methacrylate) (PPEGMEMA) brushes were grafted from both flat silica substrates as well as silica nanoparticles. Subsequently, the degrafting of the surface-tethered polymer chains was investigated in cell culture medium and phosphate buffered saline (PBS) using various techniques. The aim of the final two Chapters of this Thesis is less on exploring the chain conformation of polymer chains grafted by SI-CRP, but more to use the ability of SI-CRP to prepare thin polymer films that present a high surface concentration of functional groups to mediate soft tissue adhesion. Chapter 3 describes the preparation of photo-active poly(2-hydroxyethyl methacrylate) (PHEMA) brushes as soft tissue bioadhesives. Tissue adhesion in this Chapter is induced as UV-irradiation of PHEMA brushes converts the initially bio-inert side chain hydroxyl groups of these brushes into (putatively) aldehyde groups, which can react with amine groups present in the tissue. The prepared PHEMA brush coated substrates are biocompatible, which avoids fibrous capsule formation and presents functionalities that can be transformed, on-demand, from a non-reactive, non-adhesive state to a reactive, adhesive state in wet tissue environment. While the photoactivation of the PHEMA side chain functional groups is very efficient, it is not very well defined from a chemistry point of view. Chapter 4 therefore, explores an alternative photoactivation chemistry, which is based on the use of the diazirine motif. These diazirine motifs were incorporated in poly(2-hydroxyethyl methacrylate-co-poly(ethylene glycol) methyl ether methacrylate) (P(HEMA-co-PEGMEMA)) copolymer brushes via post-polymerization modification. These diazirine modified brushes are attractive as they may not only be activated by UV-light but also by electrochemical means.

EPFL2016

Synthesis of Responsive Polymer Brushes for Sensing Applications

Nicolas Bertrand Schüwer

During the past decades the field of sensors has been subject to much attention due to an increased demand for (bio)sensors and environmental monitoring. The efforts have been concentrated to create sensors which are reliable, highly sensitive and selective, small and fast responding. Surface modification by polymer coating has been proven an excellent method to introduce selectivity on actuators. Among the various techniques that allow the formation of polymer thin film, polymer brushes have gained attention along the past decades due to their unique structure and the possibility offered by controlled/"living" surface-initiated radical polymerization technique to generate polymer thin film with precisely controlled thickness, composition and architecture. Polymer brushes have found numerous applications including nonbiofouling surfaces and cell adhesive surfaces, protein binding and immobilization, chromatography supports, membrane functionalization, responsive surface, antibacterial coatings or low friction surfaces. Despite their interesting properties and the numerous reports describing the potential of polymer brush as responsive surface, their use for "real" sensing applications has receive little or no attention so far. This Thesis describes how polymer brushes can be employed as selective surface modification for sensing application. We aimed at synthesizing polymer thin film able to detect analytes of interest, with a particular focus on low detection limit and high selectivity. After a short introduction to the field of polymer brushes (Chapter 1), Chapter 2 presents a review of the work accomplished in the field of responsive polymer brushes with an emphasis on solvent responsive, thermoresponsive, pH- and ion-sensitive polymer brushes. The pH-induced swelling and collapse of surface-tethered, weak polyelectrolyte brushes is of interest not only for the development of responsive surface coatings but also for the pH controlled transport or adsorption. Chapter 3 discusses results of an extensive series of quartz crystal microbalance (QCM) experiments that aimed at further understanding the influence of brush thickness and density on the pH-responsiveness of poly(methacrylic acid) (PMAA) brushes and developing strategies that allow to engineer the pH responsiveness and dynamic response range of PMAA based brushes. It was observed that due to their high grafting density, the apparent pKa of surface-tethered PMAA differs from that of the corresponding free polymer in solution and also covers a broader pH range. The pKa of the PMAA brushes was found to depend both on brush thickness and density; thicker brushes showed a higher pKa value and brushes of higher density started to swell at higher pH. The second part of this section demonstrates the feasibility of the N-hydroxysuccinimide-mediated post-polymerization modification to engineer the pH responsiveness of the PMAA brushes. By using appropriate amine functionalized acids, it was possible to tune both the pH of maximum response as well as the dynamic response range of these PMAA based polyelectrolyte brushes. In Chapter 4, benzo-15-crown-5 functionalized polymer brushes prepared via surface-initiated atom transfer radical polymerization were used as the active layer in a potassium-selective QCM sensor. The polymer brushes allowed the selective detection of potassium ions, even in the presence of a large excess of sodium ions and the sensitivity of the sensor could be tuned by varying the brush thickness. Chapter 5 demonstrates the possibility to use peptide functionalized polymer brush, prepared via surface-initiated atom transfer radical polymerization (SI-ATRP), to probe heavy metal ions via voltammetric based methods. The polymer brush enhanced the mercury (II) ions sensitivity as compared to the bar electrode and allowed the detection of mercury down to the nanomolar concentration range. Furthermore it was demonstrated that the heavy metal recognition is a reversible and reproducible process. Post-polymerization modification reactions are widely employed to prepare functional polymer brushes. Relatively little is known, however, about the distribution of functional groups in such post-modified brushes. Using neutron reflectivity and UV-visible spectroscopy as principal tools, Chapter 6 investigates the p-nitrophenyl chloroformate (NPC) mediated post-polymerization modification of poly(2-hydroxyethyl methacrylate) (PHEMA) brushes, prepared via surface-initiated atom transfer radical polymerization, with D-10 leucine and D-3 serine. The neutron reflectivity experiments indicate that the post-polymerization modification depends both on the brush thickness and density. Whereas, for dense brushes, post-polymerization modification with D-10 leucine is limited to the top ∼ 200 Å of the brush, independently of the brush thickness, the extent of post-modification can be significantly extended by decreasing brush density, or by using the more hydrophilic and sterically less demanding D-3 serine, which reflects the ability of this amino acid to more readily penetrate the brush. UV-vis. experiment revealed that the NPC activation is also non-uniform, but brush thickness and density dependent, which adds to brush thickness, density and the nature of the amino acid as another of a complex set of variables that determine the final distribution of functional groups in post-modified brushes.

EPFL2011

Microfluidic engineering of artificial stem cell niches

Simone Allazetta

Stem cells play a key role in a wide range of biological processes, in large part due to their ability to self-renew or differentiate into specialized cell types in response to various biological cues. In vivo, stem cells reside in a complex microenvironment, termed niche, that regulates cell fate through intricate combinations of biophysical and biochemical factors. To recapitulate some of these crucial interactions ex vivo and to facilitate a quicker transition to clinical and pharmaceutical applications of stem cells, numerous technologies have been developed in recent years to better control and manipulate the cellular microenvironment. In particular, combining synthetic hydrogels having controllable mechanical and biochemical signaling with microfluidic technologies that can automatically and precisely handle fluids results in unprecedented control over in vitro microenvironmental conditions. In this thesis, novel microfluidic approaches were developed to engineer stem cell niches presenting defined and modular cell-instructive physicochemical cues. In a first approach, a novel platform based on computer-controlled hydrodynamic flow focusing was developed in order to tether steady-state gradients of tagged proteins, using Fc or biotin tags, onto the surface of poly(ethylene glycol) (PEG)-based hydrogels displaying selective capturing proteins (ProteinA or NeutrAvidin). This versatile patterning strategy permitted the generation of complex biomolecule gradients, with fine control over the patterning resolution and shape. Furthermore, the chosen binding schemes enabled parallel and orthogonal gradients of multiple proteins to be formed. As a proof-of-principle, we employed this technology to assess the influence of immobilized leukemia inhibitor factor (LIF) concentration on mouse embryonic stem cell self-renewal. While this technology allowed biomolecule dose effect on stem cell behavior to be investigated, it was limited in its ability to modulate multiple microenvironmental factors simultaneously. To address this limitation, droplet-based microfluidic technology was adopted which allows perturbing microenvironmental conditions in a combinatorial fashion and with nearly unmatched precision and throughput. To this end, microfluidic chips were fabricated for the generation of PEG-based microgels with precisely controlled dimensions and physico-chemical properties. First, we developed a versatile biofunctionalization technique for tethering biomolecules of interest to the reactive PEG microgels. Then, selective peptide- and protein-modified formulations were tested for their ability to promote adhesion and proliferation of various stem cell types in a bioreactor-based suspension culture. Next, programmable modulation of the flows was adopted to generate microgels with varying elasticity, biochemical ligands or both. The different microgel properties were encoded with specific fluorescent markers such that the microenvironment properties could be readily identified via microscopy or flow cytometry. Controlling syringe pumps through computer programming allowed us to generate up to 100 populations of microgels with different elasticities and bioactive ligand concentrations in a single experiment. Thousands of compositionally distinct microgels were then analyzed by the intensity levels of two fluorescent moieties incorporated in the hydrogel network. As a proof-of-principle, we demonstrated that this technology can be adopted to [...]

EPFL2015