Quanta burst photography | EPFL Graph Search

Single-photon avalanche diodes (SPADs) are an emerging sensor technology capable of detecting individual incident photons, and capturing their time-of-arrival with high timing precision. While these sensors were limited to singlepixel or low-resolution devices in the past, recently, large (up to 1 MPixel) SPAD arrays have been developed. These single-photon cameras (SPCs) are capable of capturing high-speed sequences of binary single-photon images with no read noise. We present quanta burst photography, a computational photography technique that leverages SPCs as passive imaging devices for photography in challenging conditions, including ultra low-light and fast motion. Inspired by recent success of conventional burst photography, we design algorithms that align and merge binary sequences captured by SPCs into intensity images with minimal motion blur and artifacts, high signal-to-noise ratio (SNR), and high dynamic range. We theoretically analyze the SNR and dynamic range of quanta burst photography, and identify the imaging regimes where it provides significant benefits. We demonstrate, via a recently developed SPAD array, that the proposed method is able to generate high-quality images for scenes with challenging lighting, complex geometries, high dynamic range and moving objects. With the ongoing development of SPAD arrays, we envision quanta burst photography finding applications in both consumer and scientific photography.

The virtual frame technique: ultrafast imaging with any camera

John Martin Kolinski

Many phenomena of interest in nature and industry occur rapidly and are difficult and cost-prohibitive to visualize properly without specialized cameras. Here we describe in detail the virtual frame technique (VFT), a simple, useful, and accessible mode of imaging that increases the frame acquisition rate of any camera by several orders of magnitude by leveraging its dynamic range. The VFT is a powerful tool for capturing rapid phenomena where the dynamics facilitate a transition between two states, and are thus binary. The advantages of the VFT are demonstrated by examining such dynamics in five physical processes at unprecedented rates and spatial resolution: fracture of an elastic solid, wetting of a solid surface, rapid fingerprint reading, peeling of adhesive tape, and impact of an elastic hemisphere on a hard surface. We show that the performance of the VFT exceeds that of any commercial high-speed camera not only in rate of imaging but also in field of view, achieving a 65MHz frame rate at 4MPx resolution. Finally, we discuss the performance of the VFT with several commercially available conventional and high-speed cameras. In principle, modern cell phones can achieve imaging rates of over a million frames per second using the VFT.

2019

Modeling and Analysis of a Direct Time-of-Flight Sensor Architecture for LiDAR Applications

Edoardo Charbon, Preethi Padmanabhan, Chunmin Zhang

Direct time-of-flight (DTOF) is a prominent depth sensing method in light detection and ranging (LiDAR) applications. Single-photon avalanche diode (SPAD) arrays integrated in DTOF sensors have demonstrated excellent ranging and 3D imaging capabilities, making them promising candidates for LiDARs. However, high background noise due to solar exposure limits their performance and degrades the signal-to-background noise ratio (SBR). Noise-filtering techniques based on coincidence detection and time-gating have been implemented to mitigate this challenge but 3D imaging of a wide dynamic range scene is an ongoing issue. In this paper, we propose a coincidence-based DTOF sensor architecture to address the aforementioned challenges. The architecture is analyzed using a probabilistic model and simulation. A flash LiDAR setup is simulated with typical operating conditions of a wide angle field-of-view (FOV = 40 ∘ ) in a 50 klux ambient light assumption. Single-point ranging simulations are obtained for distances up to 150 m using the DTOF model. An activity-dependent coincidence is proposed as a way to improve imaging of wide dynamic range targets. An example scene with targets ranging between 8–60% reflectivity is used to simulate the proposed method. The model predicts that a single threshold cannot yield an accurate reconstruction and a higher (lower) reflective target requires a higher (lower) coincidence threshold. Further, a pixel-clustering scheme is introduced, capable of providing multiple simultaneous timing information as a means to enhance throughput and reduce timing uncertainty. Example scenes are reconstructed to distinguish up to 4 distinct target peaks simulated with a resolution of 500 ps. Alternatively, a time-gating mode is simulated where in the DTOF sensor performs target-selective ranging. Simulation results show reconstruction of a 10% reflective target at 20 m in the presence of a retro-reflective equivalent with a 60% reflectivity at 5 m within the same FOV.

2019

Modeling and Analysis of a Direct Time-of-Flight Sensor Architecture for LiDAR Applications

Edoardo Charbon, Preethi Padmanabhan, Chunmin Zhang

2019