Bottom-up synthesis of graphene films hosting atom-thick molecular-sieving apertures

Incorporation of a high density of molecular-sieving nanopores in the graphene lattice by the bottom-up synthesis is highly attractive for high-performance membranes. Herein, we achieve this by a controlled synthesis of nanocrystalline graphene where incomplete growth of a few nanometer-sized, misoriented grains generates molecular-sized pores in the lattice. The density of pores is comparable to that obtained by the state-of-the-art postsynthetic etching (1012 cm-2) and is up to two orders of magnitude higher than that of molecular-sieving intrinsic vacancy defects in singlelayer graphene (SLG) prepared by chemical vapor deposition. The porous nanocrystalline graphene (PNG) films are synthesized by precipitation of C dissolved in the Ni matrix where the C concentration is regulated by controlled pyrolysis of precursors (polymers and/or sugar). The PNG film is made of few-layered graphene except near the grain edge where the grains taper down to a single layer and eventually terminate into vacancy defects at a node where three or more grains meet. This unique nanostructure is highly attractive for the membranes because the layered domains improve the mechanical robustness of the film while the atom-thick molecular-sized apertures allow the realization of large gas transport. The combination of gas permeance and gas pair selectivity is comparable to that from the nanoporous SLG membranes prepared by state-of-the-art postsynthetic lattice etching. Overall, the method reported here improves the scale-up potential of graphene membranes by cutting down the processing steps.

Gas Separation Membranes with Atom-Thick Nanopores: The Potential of Nanoporous Single-Layer Graphene

Kumar Varoon Agrawal, Deepu Joseph Babu, Kuang-Jung Hsu, Cédric Karel J Van Goethem, Luis Francisco Villalobos Vazquez de la Parra

Gas separation is one of the most important industrial processes and is poised to take a larger role in the transition to renewable energy, e.g., carbon capture and hydrogen purification. Conventional gas separation processes involving cryogenic distillation, solvents, and sorbents are energy intensive, and as a result, the energy footprint of gas separations in the chemical industry is extraordinarily high. This has motivated fundamental research toward the development of novel materials for highperformance membranes to improve the energy efficiency of gas separation. These novel materials are expected to overcome the intrinsic limitations of the conventional membrane material, i.e., polymers, where a longstanding trade-off between the separation selectivity and the permeance has motivated research into nanoporous materials as the selective layer for the membranes. In this context, atom-thick materials such as nanoporous single-layer graphene constitute the ultimate limit for the selective layer. Gas transport from atom-thick nanopores is extremely fast, dependent primarily on the energy barrier that the gas molecule experiences in translocating the nanopore. Consequently, the difference in the energy barriers for two gas molecules determines the gas pair selectivity. In this Account, we summarize the development in the field of nanoporous single-layer graphene membranes for gas separation. We start by discussing the mechanism for gas transport across atom-thick nanopores, which then yields the crucial design elements needed to achieve high-performance membranes: (i) nanopores with an adequate electron-density gap to sieve the desired gas component (e.g., smaller than 0.289, 0.33, 0.346, 0.362, and 0.38 nm for H2, CO2, O2, N2, and CH4, respectively), (ii) narrow pore size distribution to limit the nonselective effusive transport from the tail end of the distribution, and (iii) high density of selective pores. We discuss and compare the state-of-the-art bottom-up and top-down routes for the synthesis of nanoporous graphene films. Mechanistic insights and parameters controlling the size, distribution, and density of nanopores are discussed. Fundamental insights are provided into the reaction of ozone with graphene, which has been successfully used by our group to develop membranes with record-high carbon capture performance. Postsynthetic modifications, which allow the tuning of the transport by (i) tailoring the relative contributions of adsorbed-phase and gas-phase transport, (ii) competitive adsorption, and (iii) molecular cutoff adjustment, are discussed. Finally, we discuss practical aspects that are crucial in successfully preparing practical membranes using atom-thick materials as the selective layer, allowing the eventual scale-up of these membranes. Crack-and tear-free preparation of membranes is discussed using the approach of mechanical reinforcement of graphene with nanoporous carbon and polymers, which led to the first reports of millimeter-and centimeter-scale gas-sieving membranes in the year 2018 and 2021, respectively. We conclude with insights and perspectives highlighting the key scientific and technological gaps that must be addressed in the future research. Superscript/Subscript Available

AMER CHEMICAL SOC2022

Nanofibres de carbone sur filtre métallique comme support catalytique structuré

Pascal Tribolet

The main objectives of this work are 2-fold : The development of a novel type of composite material based on carbon nanofibers supported on sintered metal fibers filters (CNF/SMF) and to explore the use of this material as a catalytic support for a model reaction: selective hydrogenation of acetylene. The advantages of this novel support are: Due to carbon nanofibers, it combines a graphitic structure with a high specific surface area without microporosity. Supported carbon nanofibers can be used in a fixed bed reactor without very high pressure drop. Combination of two materials with high thermal conductivity gives a composite which keeps this property. It is suitable for highly exo/endothermic reactions, diminishing temperature gradients in the catalytic bed. The synthesis of carbon nanofibers on SMF filters was carried out by ethane catalytic decomposition at 655°C directly on metallic filters. An oxidation of SMF followed by a reduction in H2 create surface roughness, leading to a larger area for CNF nucleation. The CNF formation mechanism includes several steps: it starts with carbon deposition on metallic surface followed by its diffusion into the metal leading to carbides formation. When the limit of carbon solubility is attained, a layer of carbon is formed on the surface of metallic fibers. High tension within the bulk metal leads to carbide dissociation and by phase separation to graphite formation, which pushes the metallic particles through the carbon layer. Nickel, stainless steel an Inconel (an alloy of mainly nickel, iron and chromium) filters were used. The latter gave the highest uniformity of the carbon nanofibers layer showing an excellent mechanical stability. In order to control carbon deposition on the filters, a formal kinetic analysis of the decomposition reaction was undertaken. Partial orders of 1 for ethane, -2 for hydrogen and an apparent activation energy of 235 kJ/mol were obtained. The observed kinetics suggests strongly that the C – C bond scission is the rate determining step and not carbon diffusion into the metal which is often reported in the literature. The synthesis procedures like time on stream and reaction temperature were optimized: 1 hour of a mixture C2H6:H2:Ar (3:17:80) decomposition over SMFInconel at 655°C lead to ∼6% of carbon, leading to a CNF layer of 1 µm thickness covering the metallic fibers entirely. This material presents a high specific surface area (22.2 m2/g) and a low pressure drop for the gas flowing through. The carbon nanofibers have a diameter between 20 and 50 nm and a crystalline structure with platelets morphology where the graphene layers are stacked one above the other. Their surface is composed almost exclusively of carbon and hydrogen. Amongst the multiple possible applications of this novel composite material, its use as a catalyst support was assessed. Selective hydrogenation of acetylene was carried out over palladium supported on CNF/SMF and compared with commercial supports (ACF, EGF and AGF). The activated carbon fibers cloth (ACF) led to a Pd activity at least twice as E-type glass fibers tissue (EGF) or EGF covered by an alumina layer (AGF). Reaction kinetics was studied for Pd/ACF, leading to acetylene and hydrogen partial orders of -0.5 and 2.4, respectively and apparent activation energy of 50 kJ/mol. The negative partial order for C2H2 suggests high adsorption strength of this compound compared to other reagents on palladium. This particularity allows Pd to be selective. Hydrogenations are known to be structure sensitive. Therefore the catalyst activity for the model reaction depends on Pd particle size. It increases for large particle sizes. The control of this parameter was a priority. Variations of the palladium precursor, of the support and catalyst treatment were carried out. Micro-wave plasma was used since it is fast and has low energy consumption allowing chemically modifying the carbon support surface and activating catalyst after impregnation. This controls not only palladium sintering, but also decomposes tetraaminopalladate more efficiently, resulting in a catalyst activity of one order of magnitude higher. In order to control the palladium deposition on CNF/SMFInconel composite, it is important to have surface functional groups. The activation of carbon nanofibers was carried out with a 4 hours treatment in a boiling aqueous solution of hydrogen peroxide. This led to an amount on surface oxygen containing groups, per mass of carbon, higher than in ACF. Palladium particle size on the composite was controlled by support activation, the use of several metal precursors or different loadings or by a thermal treatment in argon at 500°C. Optimisation of the procedure allowed to obtain in a controlled way an average palladium particle sizes between 3.6 and 25 nm. The activity and selectivity towards ethylene of Pd/CNF/SMFInconel were observed to be higher compared to palladium supported on activated carbon, alumina or barite. Graphitic nature of carbon nanofibers, leading to strong metal-support interaction, was accounted as responsible for these improvements. The high thermal conductivity of the composite CNF/SMF ensured good heat transfer released due to the exothermicity of the reaction and allowed to work close to isothermal conditions in the catalytic bed. Finally it can be concluded, that for the first time carbon nanofibers synthesis was carried out in one step on sintered metal fibers filters, resulting in a novel structured composite material combining different specific properties and having promising potential applications.

EPFL2006

High-permeance polymer-functionalized single-layer graphene membranes that surpass the postcombustion carbon capture target

Kumar Varoon Agrawal, Guangwei He, Shiqi Huang, Mounir Driss Mensi, Emadeddin Oveisi, Mojtaba Rezaei, Luis Francisco Villalobos Vazquez de la Parra, Jing Zhao

Membrane-based postcombustion carbon capture can reduce the capture penalty in comparison to absorbent-based separation. To realize this, high-performance membranes are urgently needed with a CO2 permeance exceeding 1000 gas permeation units or GPU, and a CO2/N2 mixture separation factor exceeding 20. Here, we report a new class of organic–inorganic hybrid membranes based on single-layer graphene with a selective layer thinner than 20 nm. For this, the impermeable graphene lattice is exposed to oxygen plasma leading to a high percentage of vacancy defects (porosity up to 18.5%) and is then functionalized with CO2-philic polymeric chains. Treating a gas stream mimicking flue gas, the hybrid membranes yield a six-fold higher CO2 permeance (6180 GPU with a CO2/N2 separation factor of 22.5) than the performance target. Membranes prepared with a combination of optimized graphene porosity, pore size, and functional groups yield a CO2 permeance up to 11 790 GPU. Other membranes yield a CO2/N2 selectivity up to 57.2.