Publication

Concrete cancer : characterization of Alkali Silica Reaction early stage products by electron microscopy

Résumé

Concrete deterioration is a natural process, which has to be carefully monitored over a the service life of a structure. The Alkali-Silica Reaction (ASR) is a slow-process degradation, which devel-ops over decades and is therefore difficult to predict. Since its recognition 80 years ago, progress in understanding the fundamental mechanisms has been limited due to many parameters involved in the product formation, and the difficulty to isolate and test them separately. Such parameters include the concentrations of chemical elements in solution, the temperature and the water supply, which can evolve with time.This thesis focuses on characterizing the initial stages of ASR, in different conditions. First, early-stage products from OPC concrete in standard accelerated conditions are analyzed. The existence of two different ASR products was found. One has a granular morphology with an amorphous structure, and the second has a platey morphology with a partially crystalline structure. Both products show similar chemical compositions. Such a study at the nanometer scale was made possible using powerful mi-croscopy techniques which are Scanning Electron Microscopy (SEM) to localize the area of interest, Focused Ion Beam (FIB) to prepare ultra-thin lamellae that can be studied in Transmission Electron Microscopy (TEM) in Scanning mode (STEM) to carry out Energy Dispersive X-ray (EDX) measurements and calculate the compositions, coupled with Selected Area Electron Diffraction (SAED) to analyze the structure.Besides the first analyses, the influence of three parameters was tested. The temperature in the standard accelerated conditions, were lowered from 60°C to a more field realistic one of 38°C, to evaluate the impact on ASR procuct characteristics. At 38°C, only amorphous product was found, with different compositions, presumably due to the mixed analysis of a precursor form of the final ASR product (observable at low temperature) and the ASR product itself. In a second experiment, Supple-mentary Cementitious Materials (SCM) (fly ash and calcined clay), which are known to hinder concrete expansion, have been used as a partial replacement of OPC in the concrete mix. SCM showed no ex-pansion in the first accelerated months, and rare occurences of ASR products were found. The product composition didn't change (no aluminium uptake), although its Ca/(K+Na) ratio slightly increased in comparison to OPC samples. A third experiment studied the addition of alkali to a concrete mix con-taining calcined clays. No major change was observed in the early stage ASR product formation, de-spite the fact the product was more easily found in the sample.Finally, samples from the field and from synthetic production were also analyzed. The comparison be-tween field results and accelerated results was necessary to 1) validate the relevance of the acceler-ated tests and 2) evaluate the differences between early-stage and late-stage products found after the expansion and structure cracking has occurred. They were found to be similar in morphology (granular and platey), composition and structure, the field samples exhibiting an overall stronger crystalline behavior. The synthetic samples showed a similar morphology and composition but with mainly nano-crystalline to crystalline structure. The comparison validated the relevance and similarity with field and accelerated products. In is advised to focus in the future on amorphous to slightly nanocrystalline products, in

À propos de ce résultat
Cette page est générée automatiquement et peut contenir des informations qui ne sont pas correctes, complètes, à jour ou pertinentes par rapport à votre recherche. Il en va de même pour toutes les autres pages de ce site. Veillez à vérifier les informations auprès des sources officielles de l'EPFL.
Concepts associés (34)
Microscopie électronique en transmission
vignette|upright=1.5|Principe de fonctionnement du microscope électronique en transmission. vignette|Un microscope électronique en transmission (1976). La microscopie électronique en transmission (MET, ou TEM pour l'anglais transmission electron microscopy) est une technique de microscopie où un faisceau d'électrons est « transmis » à travers un échantillon très mince. Les effets d'interaction entre les électrons et l'échantillon donnent naissance à une image, dont la résolution peut atteindre 0,08 nanomètre (voire ).
Microscope électronique
thumb|Microscope électronique construit par Ernst Ruska en 1933.thumb|Collection de microscopes électroniques anciens (National Museum of Health & Medicine). Un microscope électronique (ME) est un type de microscope qui utilise un faisceau d'électrons pour illuminer un échantillon et en créer une très agrandie. Il est inventé en 1931 par des ingénieurs allemands. Les microscopes électroniques ont un pouvoir de résolution supérieur aux microscopes optiques qui utilisent des rayonnements électromagnétiques visibles.
Microscope électronique en transmission à balayage
vignette|Exemple de Microscope électronique en transmission à balayage VG501 Un microscope électronique en transmission à balayage (METB ou en anglais STEM pour scanning transmission electron microscope) est un type de microscope électronique dont le principe de fonctionnement allie certains aspects du microscope électronique à balayage et du microscope électronique en transmission. Une source d'électrons focalise un faisceau d'électrons qui traverse l'échantillon.
Afficher plus
Publications associées (108)

In Situ and Time-Resolved Transmission Electron Microscopy of Nanoscale Processes

Chengcheng Yan

Observing the fast dynamics of nanoscale systems is crucial in order to understand and ultimately control their behavior. Characterizing these dynamic processes requires techniques with atomic spatial resolution and a temporal resolution that matches the t ...
EPFL2023

Impact of Annealing on ZrO2 Nanotubes for Photocatalytic Application

Sami Rtimi

This work aims to study the structural, optical, and photocatalytic properties of ZrO2 nanotubes (NTs) that have been synthesized using the electrochemical anodization method. The structural and morphological characteristics of unannealed and annealed (400 ...
MDPI2023

Micromechanics of oxide inclusions in ferrous alloys

Alejandra Inés Slagter

Oxide inclusions are inevitably present in steel as a direct consequence of the steelmaking process; as a result, a cubic centimetre of modern steel will generally contain about a million of these hard and brittle micrometre-sized ceramic particles. Inclus ...
EPFL2023
Afficher plus
MOOCs associés (17)
Transmission Electron Microscopy for Materials Sciences
Learn about the fundamentals of transmission electron microscopy in materials sciences: you will be able to understand papers where TEM has been used and have the necessary theoretical basis for takin
Transmission Electron Microscopy for Materials Sciences
Learn about the fundamentals of transmission electron microscopy in materials sciences: you will be able to understand papers where TEM has been used and have the necessary theoretical basis for takin
Cement Chemistry and Sustainable Cementitious Materials
Learn the basics of cement chemistry and laboratory best practices for assessment of its key properties.
Afficher plus