Falling film evaporation on a single tube and on a tube bundle

This study is a contribution for the improvement of horizontal falling film heat exchangers. This type of evaporator has the potential to be widely used in the petrochemical industry, for the sea water desalination, or in the large refrigeration systems. An experimental test facility has been constructed in order to study the evaporation of the liquid refrigerant R-134a flowing on a vertical array of horizontal copper tubes with a length of 0.55 meter and a diameter of 19.1mm. Special care has been taken to achieve uniform liquid distribution along the top tube. Four types of tubes were tested including a plain tube, two tubes with mechanically enhanced boiling surfaces (Turbo-BII HP and Gewa-B) and a porous coated tube (High-Flux). Tube arrays with three different tube pitches were tested. Measurements were performed at three different nominal heat flux levels over a wide range of liquid overfeed. For comparison, heat transfer coefficients in pool boiling conditions were measured. The experimental parameters are the following: the liquid film Reynolds numbers from 0 to 3000, heat fluxes between 20 and 60kW/m2 and tube pitches from 22.3 and 25.5mm. The heat transfer coefficients have been measured locally at the mid point of each of the ten tubes. The study shows that there are two types of fundamental behavior characterized by a particular film Reynolds number: Over a threshold value of this Reynolds number, the nucleate boiling in the film governs the heat transfer and this heat transfer coefficient is independent of the Reynolds number. Below this threshold value, the heat transfer coefficients drop drastically due to the formation of local dry patches. The heat transfer coefficient during falling film evaporation was found to be approximately 1.3 times larger than the heat transfer coefficient during pool boiling and this multiplier was found to be dependant on the heat flux and tube spacing but not the flow mode. Finally, the understanding of the physical phenomena governing the falling film evaporation of liquid refrigerants has been improved. Furthermore, a method for predicting the film Reynolds number at the onset of dry patch formation has been developed and a heat transfer correlation for boiling iii falling films proposed. These represent significant improvements for the design of falling film evaporators.

EXPERIMENTAL STUDY ON FLOW BOILING HEAT TRANSFER OF MULTIPORT TUBES WITH R245fa AND R1234ze(E)

Bruno Agostini, John Richard Thome, Farzad Vakili Farahani

This article presents an experimental study of upward flow boiling heat transfer in multiport tubes. Usually, multiport tubes are utilized horizontally in automotive and air-conditioning systems while here there is interest in vertical flow as part of a two-phase thermosyphon electronics cooling system. Experiments were carried out in a flat aluminum extruded multiport tube, which was composed of 7 parallel rectangular channels (1.1mm × 2.1mm) with a hydraulic diameter of 1.4 mm. Two refrigerants, R245fa and the new refrigerant R1234ze, the latter a new environmentally safe refrigerant proposed as a potential replacement for R134a, were tested. A new hot water heating technique that accounts for either uniform or non-uniform local heat flux distribution along the channel, particularly for exploring high vapor qualities into the dryout region, was developed to obtain and reduce the data. Accordingly, heat transfer coefficients were measured locally for the entire range of vapor qualities starting from subcooled liquid to superheated vapor. Effects of heat flux, mass flux, vapor quality, and saturation temperature on flow boiling heat transfer in multiport tubes were considered. Finally, the experimental results were compared with some well-known correlations to evaluate the capabilities of existing prediction methods. The analysis completed so far shows that the three-zone model for slug flows works well for that subset of test results, utilizing the apparent surface roughness in place of the dryout thickness in the model, as has been previously done for silicon, stainless steel and copper microchannels with measured surface roughnesses. Notably, the non-dryout data were well predicted by the Cooper nucleate pool boiling correlation as in many other studies, although there is no proof that nucleate boiling is taking place except near the point of inception of boiling.

2012

Heat Transfer and Visualization of Falling Film Evaporation on a Tube Bundle

Marcel Christians

Horizontal falling film evaporators have the potential of displacing flooded evaporators in industry, due to advantages such as lower required refrigerant charge and lower pressure drop. However, there is a need to improve the understanding of falling film evaporation mechanisms to provide accurate thermal design methods. In this work, the existing LTCM falling film facility was utilized to perform falling film evaporation measurements on a single tube, a vertical row of horizontal tubes and a small tube bundle. Two enhanced boiling tubes, namely the Wolverine Turbo-B5 and the Wieland Gewa-B5, were tested using R-134a and R-236fa. The tests were carried out at a constant saturation temperature of Tsat = 5°C, liquid film Reynolds numbers ranging from 0 to 3000, and heat fluxes between 15 and 90 kW/m2 in pool boiling and falling film configurations. A visualization study was performed under adiabatic and diabatic conditions (in both single-array and bundle configurations) to study the flow. The physical phenomena governing the falling film evaporation process have been studied, and insight into their effects on the performance of tube bundles has been gained. Measurements of the local heat transfer coefficient were obtained and utilized to generate new prediction methods, including a method for predicting the onset-of-dryout film flow rate during falling film evaporation, local pool boiling and falling film heat transfer prediction methods and a falling film multiplier prediction method.

EPFL2010

Experimental investigation on flow boiling pressure drop and heat transfer of R1233zd(E) in a multi-microchannel evaporator

Navid Borhani, Houxue Huang, John Richard Thome

An experimental study on flow boiling pressure drop and heat transfer of a new environmentally friendly refrigerant R1233zd(E), in a parallel multi-microchannel evaporator was carried out. The silicon microchannels evaporator was 10 mm long and 10 mm wide, having 67 parallel channels, each 100 x 100 mu m(2), separated by a fin with a thickness of 50 mu m. Upstream of each channel, a micro orifice was placed to stabilize the two-phase flow and to obtain good flow distribution. The operating conditions for flow boiling tests were: mass fluxes from 500 to 2750 kg m(-2) S-1, heat fluxes from 6 to 50 W cm(-2), inlet subcooling of 5.8 K, and a nominal outlet saturation temperature of 35 degrees C for stable flow boiling. The test section's backside base temperatures were measured by an infrared (IR) camera. The stable flow boiling data without back flow was selected through flow visualization recorded by a highspeed camera coupled with a microscope. These data were then used to assess the applicability of existing two-phase pressure drop models, and to further develop a new empirical model suitable for the high mass flux operating conditions. This new pressure drop model was used to predict the local fluid temperature for the further heat transfer data identification. The fine-resolution local heat transfer coefficients were obtained by solving the three-dimensional inverse heat conduction problem. The experimental results showed that in the saturated flow boiling region the local heat transfer coefficient first decreased moderately in the very low vapor quality region (x < 0.05), then increased significantly but monotonically along the flow direction. The fine-resolution local heat transfer data at the saturated flow boiling region were compared with two groups of heat transfer correlations. The first one considered the flow boiling mechanism occurring in muliti-microchannels as a combination of nucleate boiling and forced convection boiling, while the other one associated this mechanism to liquid thin film evaporation, thus indicating a controversy. It is found that the flow pattern based model belonging to the second group yielded the best agreement with the experimental data, predicting 92.0% of this new database within 30%. (C) 2016 Elsevier Ltd. All rights reserved.