Molecular-beam/surface-science apparatus for state-resolved chemisorption studies using pulsed-laser preparation

We describe a new apparatus that combines pulsed laser excitation in a molecular beam with surface-science methods for preparation of clean single-crystal surfaces and detection of adsorbates to enable state-selected studies of gas-surface reaction dynamics. Reactant molecules are prepared in specific vibrationally excited states via overtone pumping using tunable, narrow-band laser radiation. The collision-free environment of the molecular beam prevents relaxation of the prepared molecules before impact on the target surface and enables complete control over the collision energy and incidence angle. Chemisorption products are detected after a given deposition time by Auger electron spectroscopy. To achieve sufficient beam flux of state-selected reactant molecules for product detection by standard surface-science techniques, we use a high-intensity, short-pulse molecular-beam source matched to the low duty cycle of the pulsed lasers used in our experiments. We present the design and characterization of this new apparatus together with a scheme for generating infrared laser pulses of high spectral brightness for saturating weak vibrational overtone transitions within a significant volume of the molecular beam. The effectiveness of our approach is demonstrated by state-resolved sticking coefficient measurements for overtone-excited (2nu(3)) CH4 on Ni(100) for a range of impact energies. (C) 2003 American Institute of Physics.

Quantum state-resolved gas/surface reaction dynamics probed by reflection absorption infrared spectroscopy

Rainer Beck, Régis Bisson, Li Chen, Hirokazu Ueta

We report the design and characterization of a new molecular-beam/surface-science apparatus for quantum state-resolved studies of gas/surface reaction dynamics combining optical state-specific reactant preparation in a molecular beam by rapid adiabatic passage (RAP) with detection of surface-bound reaction products by reflection absorption infrared spectroscopy (RAIRS). RAIRS is a non-invasive infrared spectroscopic detection technique that enables online monitoring of the buildup of reaction products on the target surface during reactant deposition by a molecular beam. The product uptake rate obtained by calibrated RAIRS detection yields the coverage dependent state-resolved reaction probability S(θ). Furthermore, the infrared absorption spectra of the adsorbed products obtained by the RAIRS technique provide structural information, which help to identify nascent reaction products, investigate reaction pathways, and determine branching ratios for different pathways of a chemisorption reaction. Measurements of the dissociative chemisorption of methane on Pt(111) with this new apparatus are presented to illustrate the utility of RAIRS detection for highly detailed studies of chemical reactions at the gas/surface interface.

American Institute of Physics2013

Bond-selective and surface-site-specific dissociation of methane on platinum

Ana Gutiérrez González

I present a molecular beam study of methane dissociation on differ-ent surface sites of several platinum single crystal surfaces (Pt(111), Pt(211), Pt(210), Pt(110)-(2x1)). The experiments were performed in a molecular beam/surface-science apparatus that combines rovibrational state-selective excitation of reactants with detection of the reaction products by reflection absorption infrared spectroscopy (RAIRS), Auger electron spectroscopy (AES) and King and Wells (K&W) technique. First, I explore how the barrier for methane dissociation depends on the Pt surface site (terrace, step, kink, and ridge atoms). For that, I compare the average reaction probabilities of methane on the different crystals using K&W. Moreover, I used the site-specific detection of chemisorbed methyl species by RAIRS to obtain the site-specific reactivity on steps, ridges and terraces. The highest methane reactivity and therefore the lowest barrier was observed for the surface atoms with the lowest coordination. The trans-lational energy dependence of the reactivity shows clear evidence for a direct activated mechanism on all the surface sites studied. The decreasing catalyt-ic activity for Pt atoms with increasing coordination number agrees well with theoretical predictions using first principles quantum theory calculations. Second, I present the role of rovibrational excitation of the incident methane on the chemisorption on different surface sites. For CH4, excitation of one quantum of the antisymmetric C-H stretch vibration (Îœ3) was found to be less efficient than an equivalent amount of translational energy normal to the sur-face for promoting the dissociation on all the surface sites. The vibrational efficacy was seen to be lower for dissociation on the low coordinated sites, in accordance with calculations of transition state geometries. For CH3D, the excitation of the antisymmetric C-H stretch vibration (Îœ4) led to bond selec-tivity on the steps and terraces of the Pt(211) surface. These results show how careful control of the translational energy and rovibrational state of the incident CH3D can be used for site-specific and bond-selective dissociation of methane. As predicted previously by theory but not observed before experi-mentally, the C-H bond selectivity is shown to decrease with increasing translational energy. Third, I explore the effect of surface temperature on the methane dissocia-tion. The sticking coefficient for a direct chemisorption reaction such as CH4 on Pt, might be expected to be independent of surface temperature, because the reaction happens very fast leaving very little time for the molecule to equilibrate with the surface. However, I observed an increase in methane reactivity with increasing surface temperature at low incident CH4 energies. This observation is interpreted by a âloss of coordinationâ from the atoms displaced out of the plane due to their vibrational motion when the surface is heated. The surface-site and quantum-state-specific data presented in this thesis are ideally suitable for testing theoretical models that aim to describe the me-thane-surface reaction at the microscopic level. Moreover, the characteriza-tion of different catalytically active sites for methane dissociation contrib-utes to advancing the understanding of methane reactivity towards real cata-lytic conditions, where surfaces with several different atomic terminations are used.

EPFL2019

Electrospray Ion Beam Deposition of Complex Non-Volatile Molecules

Gordon Rinke

The rational synthesis of novel materials requires the control over the arrangement of matter in order to meet the desired properties for applications and devices. Ultimately, control means to define the place of each atom and determine its chemical state, as well as being able to confirm the result in a measurement. Control at the atomic level can be achieved with scanning tunneling microscopy (STM), both in imaging and atomic manipulation. The latter, however, can never be used in meso- or even macroscopic material synthesis. Self-ordering phenomena determines atomic control in material synthesis as well, observed for instance in protein folding or in molecular beam epitaxy (MBE) technology. In both cases the atomically determined arrangement of the atoms in the structure is controlled only by environmental parameters that steer the self-ordering phenomena. In this thesis I show that electrospray ion beam deposition (ES-IBD) or ion soft-landing is a material processing technique, which combines and even extends the level of control offered by MBE. It is demonstrated that a vast range of complex organic materials including peptides and proteins is now available to ultrapure vacuum processing and moreover completely novel schemes of controlling self-ordering processes are provided. In-situ STM is applied to investigate the structure formation of complex molecules deposited by ES-IBD on well-defined, clean, and atomically flat surfaces in ultrahigh vacuum at the greatest detail. This allows us to explore the novel control features that are intrinsic to the ES-IBD deposition process like online coverage monitoring, deposition energy control, and mass-selection to select charge states or reactive species. The molecules studied here include organic molecular salts, dye molecules, reactive polymer building blocks, and finally peptides and proteins. Crystalline layer-by-layer as well as island growth was observed and revealed the equivalence to conventional MBE growth. On the basis of these deposition experiments the crucial influence of clusters in the ion beam for high material flux was discovered. Furthermore, it was found that the chemical state of the molecule is a key factor for the deposition result as chemical reactions can be induced or the self-assembly behavior can be altered. Alongside the capability to handle also extremely reactive molecules, the feasibility to control chemical reactions occurring as a result of an external stimulus to a specifically selected reactive species is demonstrated. Employing the control parameters that are specific to ES-IBD like charge state selection and deposition energy to complex biomolecules opens up new perspectives for vacuum deposition. In addition to the self-assembly governed by the molecule-substrate and molecule-molecule interaction, it was possible to actively steer the structure formation of proteins by influencing their stiffness and their reactivity through their charge state as well as by the deposition energy, parameters intrinsic to the ES-IBD method. Hence, electrospray ion beam deposition is indeed a tool to prepare well defined surface coatings at highest level of control and complexity. To be relevant for industrial applications, the performance of the system has to be further improved, most importantly in terms of deposition rate. In general, ES-IBD enables new approaches for the growth of functional coatings but also serving as perfect sample preparation tool for the characterization of complex molecules on the atomic scale by scanning probe or more general surface science methods.