The effect of stress triaxiality on the phase transformation in transformation induced plasticity steels: Experimental investigation and modelling the transformation kinetics

À propos
Confidentialité
Mentions légales

Graph Chatbot

Publications associées (30)

Crystalline or amorphous? A critical evaluation of phenomenological phase selection rules

Johann Michler, Caroline Hain, Ashish Sharma

In this work, we reviewed the available phase selection rules comprising atomic size and topological aspects, entropies, enthalpies, melting points, valence and itinerant electron concentrations, as well as electronegativity, and validated them using a car ...

ELSEVIER SCI LTD2023

Drained Clay-Pipe Interface Resistance at Low Normal Stresses and Elevated Temperatures

Roba Houhou

Offshore pipelines that transport hydrocarbons under high pressure and high temperature are usually thermally insulated to maintain an elevated temperature and prevent any heat loss to the surroundings. However, the temperatures at the outer-wall of the pi ...

AMER SOC CIVIL ENGINEERS2023

Deformation response of highly stretchable and ductile graphene kirigami under uniaxial and biaxial tension

Ye Wei, Yao Chen, Tong Guo

Kirigami, the ancient technique of paper cutting, has been successfully applied to enhance the stretchability and ductility of nanoscale graphene. However, existing experimentally realized graphene kirigami (GK) are created by introducing parallel cuts, ex ...

Amer Physical Soc2023

Control of intermetallics in the interface in directed energy deposition of titanium on stainless steel 316L

Di Cui

Application of a single metal or alloy is often restricted by its properties from optimal combination of performance and cost. Therefore, there is a vast need of joining dissimilar metals for various applications in biomedical, aerospace, automobile and ma ...

EPFL2023

Micromechanics of oxide inclusions in ferrous alloys

Alejandra Inés Slagter

Oxide inclusions are inevitably present in steel as a direct consequence of the steelmaking process; as a result, a cubic centimetre of modern steel will generally contain about a million of these hard and brittle micrometre-sized ceramic particles. Inclus ...

EPFL2023

Shearing and opening of a pre-existing discontinuity in response to fluid injection

Brice Tanguy Alphonse Lecampion, Alexis Alejandro Sáez Uribe, Ankit Gupta

We investigate the fluid-driven growth of a shear crack along a frictional discontinuity and its transition to hydraulic fracturing (sometimes referred to as hydraulic jacking) under plane-strain conditions. We focus on the case of a constant friction coef ...

2023

Tailor-made Piezoelectric Elastomer Materials

Francis Owusu

Recent advancements in miniature devices with higher computational capabilities and ultralow power consumption have accelerated the development of wearable sensors, actuators, and energy harvesters everywhere. The ultimate aim of such a technological revol ...

EPFL2023

Nanomechanical Modeling of the Bending Response of Silicon Nanowires

Yusuf Leblebici, Zuhal Tasdemir, Mohammad Nasr Esfahani, Mustafa Yilmaz

Understanding the mechanical behavior of silicon nanowiresis essentialfor the implementation of advanced nanoscale devices. Although bendingtests are predominantly used for this purpose, their findings shouldbe properly interpreted through modeling. Variou ...

AMER CHEMICAL SOC2023

EBSD study of variant reorientation, texture, and twin formation in a martensitic NiTi alloy deformed in compression

Cyril Cayron, Roland Logé, Mathijs Pieter van der Meer, Junfeng Xiao

Martensitic crystallography plays a vital role in the texture evolution and mechanical properties in Nickel-Titanium (NiTi) shape memory alloys when subjected to deformation. However, their microstructural changes during deformation are not well known and ...

Pergamon-Elsevier Science Ltd2023

Micro-addition of Fe in highly alloyed Cu-Ti alloys to improve both formability and strength

Roland Logé, Cyril Cayron, Baptiste Thomas Jean Rouxel

Cu-Be alloys provide excellent electrical and mechanical properties, but present serious health hazards during manufacturing. Among alternative alloys, the Cu-Ti system has the highest yield strength; however, Ti cannot be easily solutionized at concentrat ...

ELSEVIER SCI LTD2022

Page 3 sur 3