A virtual circuit (VC) is a means of transporting data over a data network, based on packet switching and in which a connection is first established across the network between two endpoints. The network, rather than having a fixed data rate reservation per connection as in circuit switching, takes advantage of the statistical multiplexing on its transmission links, an intrinsic feature of packet switching.
A 1978 standardization of virtual circuits by the CCITT imposes per-connection flow controls at all user-to-network and network-to-network interfaces. This permits participation in congestion control and reduces the likelihood of packet loss in a heavily loaded network. Some circuit protocols provide reliable communication service through the use of data retransmissions invoked by error detection and automatic repeat request (ARQ).
Before a virtual circuit may be used, it must be established between network nodes in the call setup phase. Once established, a bit stream or byte stream may be exchanged between the nodes, providing abstraction from low-level division into protocol data units, and enabling higher-level protocols to operate transparently.
An alternative to virtual-circuit networks are datagram networks.
Virtual circuit communication resembles circuit switching, since both are connection oriented, meaning that in both cases data is delivered in correct order, and signaling overhead is required during a connection establishment phase. However, circuit switching provides a constant bit rate and latency, while these may vary in a virtual circuit service due to factors such as:
varying packet queue lengths in the network nodes,
varying bit rate generated by the application,
varying load from other users sharing the same network resources by means of statistical multiplexing, etc.
This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.
Ce cours introduit les lois fondamentales de l'électricité et les méthodes permettant d'analyser des circuits électriques linéaires, composés de résistances, condensateurs et inductances. On commencer
Master the design of circuits and systems at high frequency (HF) and very high frequency (VHF) (1 MHz-6GHz). This lecture is particularly oriented towards circuit aspects of modern communications syst
In telecommunications, packet switching is a method of grouping data into packets that are transmitted over a digital network. Packets are made of a header and a payload. Data in the header is used by networking hardware to direct the packet to its destination, where the payload is extracted and used by an operating system, application software, or higher layer protocols. Packet switching is the primary basis for data communications in computer networks worldwide.
Multiprotocol Label Switching (MPLS) is a routing technique in telecommunications networks that directs data from one node to the next based on labels rather than network addresses. Whereas network addresses identify endpoints the labels identify established paths between endpoints. MPLS can encapsulate packets of various network protocols, hence the multiprotocol component of the name. MPLS supports a range of access technologies, including T1/E1, ATM, Frame Relay, and DSL. In an MPLS network, labels are assigned to data packets.
In telecommunications and computer networking, connection-oriented communication is a communication protocol where a communication session or a semi-permanent connection is established before any useful data can be transferred. The established connection ensures that data is delivered in the correct order to the upper communication layer. The alternative is called connectionless communication, such as the datagram mode communication used by Internet Protocol (IP) and User Datagram Protocol, where data may be delivered out of order, since different network packets are routed independently and may be delivered over different paths.
The time-resolved visualization of the dynamics of a cavitation bubble usually requires the use of expensive high-speed cameras, which often provide a limited spatial resolution. In the present study, we propose an alternative to these high-speed imaging t ...
New York2023
, ,
The Medipix4 chip is the latest member in the Medipix/Timepix family of hybrid pixel detector chips aimed at high -rate spectroscopic X-ray imaging using high -Z materials. It can be tiled on all 4 sides making it ideal for constructing large -area detecto ...
Iop Publishing Ltd2024
, ,
In this work, we develop timing-driven CAD support for FPGA architectures with direct connections between LUTs. We do so by proposing an efficient ILP-based detailed placer, which moves a carefully selected subset of LUTs from their original positions, so ...