Girder | EPFL Graph Search

A girder ('gɜrdər) is a beam used in construction. It is the main horizontal support of a structure which supports smaller beams. Girders often have an I-beam cross section composed of two load-bearing flanges separated by a stabilizing web, but may also have a box shape, Z shape, or other forms. Girders are commonly used to build bridges. A girt is a vertically aligned girder placed to resist shear loads. Small steel girders are rolled into shape. Larger girders (1 m/3 feet deep or more) are made as plate girders, welded or bolted together from separate pieces of steel plate. The Warren type girder replaces the solid web with an open latticework truss between the flanges. This arrangement combines strength with economy of materials, minimizing weight and thereby reducing loads and expense. Patented in 1848 by its designers James Warren and Willoughby Theobald Monzani, its structure consists of longitudinal members joined only by angled cross-members, forming alternately i

Composite action of FRP bridge decks adhesively bonded to steel main girders

Herbert Gürtler

Up until today reinforced concrete has been used in most cases for the manufacturing of bridge decks. Depending on the quality of the work carried out, defects can already occur after only a few years. These defects mostly appear in the form of corrosion of the steel reinforcement due to concrete's sensitivity to de-icing salts and water. To reduce maintenance costs, which are mainly caused by corrosion of the steel reinforcement, attempts were made to eliminate the steel reinforcement in the bridge deck. This was achieved for example by replacing the whole concrete bridge deck with an FRP1 bridge deck. FRP bridge decks, besides the advantage of the absence of steel reinforcement, exhibit the advantage of a low dead load (approx. 20% of a comparable concrete deck) combined with high strength. These properties resulted in the fact that today more than 200 bridges with FRP decks are in service worldwide. Most of them need steel or concrete main girders to bridge the required span. Despite the many bridges already in service, assessment of their load-bearing capacity or deflections still remains difficult. Some of the reasons for this this are as follows: Geometry and material properties vary considerably between different FRP bridge-deck types. The problem of the connection between main girders and bridge decks has only been partially solved. No design method exists which allows determination of the stresses and deflections of composite girders, and takes the degree of composite action of the bridge deck into account. This thesis contributes to solve these problems. Experiments with two different bridge decks were carried out in order to determine the necessary system properties (in-plane compression and shear resistance and in-plane compression and shear stiffness) for the calculation of the load-bearing behavior of steel/FRP composite girders. The method developed to determine the system properties can also be applied to other FRP bridge decks (e.g. sandwich decks). In a second step, four composite girders (two with each bridge deck) were manufactured by bonding the bridge decks onto conventional steel girders. Local failure of the bridge deck, as occurs in girders with stud or bolt connections, is therefore prevented and a clear load transfer in the joint is assured. One of the two girders, with each bridge deck system, was tested statically and the other statically and under fatigue loads. The results of the girder experiments showed that adhesive bonding is a reliable connection technique, since failure always occurred first in the bridge deck and then in the adhesive layer. The stiffness and failure load of the composite girders could be increased considerably in comparison with the pure steel girder. The determined system properties concerning in-plane shear and compression stiffness were confirmed with the girder experiments. The results of the experiments with the composite girders were compared with results of an analytical design method for concrete/wood girders adapted for steel/FRP composite girders. It was shown that the load-bearing behavior of composite girders consisting of steel main girders and adhesively- bonded FRP bridge decks can be determined with good accuracy in the linear-elastic region. Furthermore a design method was developed which allows the loadbearing capacity of the steel/FRP composite girders investigated in this thesis to be determined with very good accuracy. Subsequently a parameter study was carried out in order to verify the assumption of full composite action in the adhesively- bonded joint. This is one of the requirements for application of the developed design methods. The study showed that the assumption is applicable for different adhesives and even for thicknesses up to 50 mm. ---------------------------------------- 1 Fiber Reinforced Polymer

EPFL2005

Through-thickness performance of adhesive connections between FRP bridge decks and steel main girders

Martin Schollmayer

FRP bridge decks offer several advantages compared with conventional concrete bridge decks, particularly their much lower weight, but also their resistance against corrosion as well as easier installation and maintenance. The poorly conceived methods available for connecting FRP bridge decks with their supporting structures – normally steel girders – nonetheless constitute a disadvantage. Connections involving studs or bolts are not appropriate in this case, since FRP is a very brittle material that offers no ductile properties. Bolted connections usually result in much higher stress concentrations, while adhesive bonding is a more material-adapted connection method since larger surfaces can be linked together, thus ensuring reduced stresses. The bridge system investigated in this thesis consists of a pultruded FRP bridge deck bonded to steel main girders, the bridge's main structural components, which have to transmit the dead and traffic loads to the supports, whereas the bridge deck is spanned in the transverse direction perpendicular to the steel girders. Uplift forces caused by the load-bearing behavior of the bridge deck transverse to the bridge axis lead to through-thickness tensile stresses in the adhesive joint. The main objective of this thesis is the description of the structural behavior in the transverse direction. This includes analysis of the stresses in the adhesive connection as well as determination of the strength of the joints. Analytical and experimental investigations were carried out. It was shown, that the tensile stress distribution in the adhesive joint is non-uniform with high stress concentrations below the FRP deck webs of the cellular deck and above the steel girder web. Alternately inclined deck webs thereby induce significantly higher stresses below the vertical webs. A method for the calculation of the stress state in the adhesive layer is proposed which is validated by numerical and experimental results. The material strength of the connection in terms of a combination of tensile through-thickness and shear stresses is established. The total safety factor of the joint was higher than the safety factor of the FRP deck for bending between the main girders. A possible failure process would not start in the adhesive connection between bridge deck and steel girder which eventually could lead to additional failure of other structural members. The system is redundant. Fatigue loading up to 10 million cycles showed no stiffness degradation. The results of this thesis prove the existence of a good load-bearing behavior under static and fatigue loads of adhesively-bonded joints between pultruded FRP bridge decks and structural steel girders, where the adhesive connection is loaded with uplift forces and moments acting in the bridge deck, in addition to the shear in the connection layer due to composite action. The basis for a design method for adhesively-bonded connections between pultruded FRP bridge decks and steel girders is provided.

EPFL2009

Composite action and adhesive bond between fiber- reinforced polymer bridge decks and main girders

Herbert Gürtler, Thomas Keller

This paper describes the behavior of hybrid girders consisting of fiber-reinforced polymer (FRP) bridge decks adhesively connected to steel main girders. Two large-scale girders were experimentally investigated at the serviceability and ultimate limit state as well as at failure. One of the girders was additionally fatigue loaded to 10 million cycles. Compared to the behavior of a reference steel girder, deflections of the two girders at the SLS were decreased by 30% and failure loads increased by 56% due to full composite action in the adhesive layer. A ductile failure mode occurred: Deck compression failure during yielding of the steel girder. The adhesive connections were able to prevent buckling of the yielding top steel flanges. Thus, compared to the reference steel girder, the maximum deflections at failure could be increased up to 130%. No deterioration due to fatigue loading was observed. Based on the experimental results, a conceptual design method for bonded FRP/steel girders was developed. The proposed method is based on the well- established design method for hybrid girders with concrete decks and shear stud connections. The necessary modifications are proposed. © ASCE

2005