In telecommunication, frame synchronization or framing is the process by which, while receiving a stream of framed data, incoming frame alignment signals (i.e., a distinctive bit sequences or syncwords) are identified (that is, distinguished from data bits), permitting the data bits within the frame to be extracted for decoding or retransmission.
If the transmission is temporarily interrupted, or a bit slip event occurs, the receiver must re-synchronize.
The transmitter and the receiver must agree ahead of time on which frame synchronization scheme they will use.
Common frame synchronization schemes are:
Framing bit A common practice in telecommunications, for example in T-carrier, is to insert, in a dedicated time slot within the frame, a noninformation bit or framing bit that is used for synchronization of the incoming data with the receiver. In a bit stream, framing bits indicate the beginning or end of a frame. They occur at specified positions in the frame, do not carry information, and are usually repetitive.
Syncword framing Some systems use a special syncword at the beginning of every frame.
CRC-based framing Some telecommunications hardware uses CRC-based framing.
In telemetry applications, a frame synchronizer is used to frame-align a serial pulse code-modulated (PCM) binary stream.
The frame synchronizer immediately follows the bit synchronizer in most telemetry applications. Without frame synchronization, decommutation is impossible.
The frame synchronization pattern is a known binary pattern which repeats at a regular interval within the PCM stream. The frame synchronizer recognizes this pattern and aligns the data into minor frames or sub-frames. Typically the frame sync pattern is followed by a counter (sub-frame ID) which dictates which minor or sub-frame in the series is being transmitted. This becomes increasingly important in the decommutation stage where all data is deciphered as to what attribute was sampled. Different commutations require a constant awareness of which section of the major frame is being decoded.
This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.
Data communication or digital communications, including data transmission and data reception, is the transfer and reception of data in the form of a digital bitstream or a digitized analog signal transmitted over a point-to-point or point-to-multipoint communication channel. Examples of such channels are copper wires, optical fibers, wireless communication using radio spectrum, storage media and computer buses. The data are represented as an electromagnetic signal, such as an electrical voltage, radiowave, microwave, or infrared signal.
Time-division multiplexing (TDM) is a method of transmitting and receiving independent signals over a common signal path by means of synchronized switches at each end of the transmission line so that each signal appears on the line only a fraction of time in an alternating pattern. It can be used when the bit rate of the transmission medium exceeds that of the signal to be transmitted. This form of signal multiplexing was developed in telecommunications for telegraphy systems in the late 19th century, but found its most common application in digital telephony in the second half of the 20th century.
The data link layer, or layer 2, is the second layer of the seven-layer OSI model of computer networking. This layer is the protocol layer that transfers data between nodes on a network segment across the physical layer. The data link layer provides the functional and procedural means to transfer data between network entities and may also provide the means to detect and possibly correct errors that can occur in the physical layer. The data link layer is concerned with local delivery of frames between nodes on the same level of the network.
Digital micro-mirror devices (DMDs) have been deployed in many optical applications. As compared to spatial light modulators (SLMs), they are characterized by their much faster refresh rates (full-frame refresh rates up to 32 kHz for binary patterns) compa ...
NATURE PORTFOLIO2021
, ,
This paper presents optimization methods to design frame structures from a stock of existing elements. These methods are relevant when reusing structural elements over multiple service lives. Reuse has the potential to reduce the environmental impact of bu ...
2020
, , ,
Flexure pivot based system (1) being one of: a force sensor, a force limiting device arranged to exert a predetermined threshold force, a torque limiting device arranged to exert a predetermined threshold torque, a programmable mechanical memory, or an acc ...