A diffuser is "a device for reducing the velocity and increasing the static pressure of a fluid passing through a system”. The fluid's static pressure rise as it passes through a duct is commonly referred to as pressure recovery. In contrast, a nozzle is used to increase the discharge velocity and lower the pressure of a fluid passing through it.
Frictional effects during analysis can sometimes be important, but usually they are neglected. Ducts containing fluids flowing at low velocity can usually be analyzed using Bernoulli's principle. Analyzing ducts flowing at higher velocities with Mach numbers in excess of 0.3 usually require compressible flow relations.
A typical subsonic diffuser is a duct that increases in area in the direction of flow. As the area increases, fluid velocity decreases, and static pressure rises.
A supersonic diffuser is a duct that decreases in area in the direction of flow which causes the fluid temperature, pressure, and density to increase, and velocity to decrease. These changes occur because the fluid is compressible. Shock waves may also play an important role in a supersonic diffuser.
Diffusers are very common in heating, ventilating, and air-conditioning systems. Diffusers are used in both all-air and air-water HVAC systems, as part of room air distribution subsystems, and serve several purposes:
To deliver both conditioning and ventilating air
Evenly distribute the flow of air, in the desired directions
To enhance mixing of room air into the primary air being discharged
Often to cause the air jet(s) to attach to a ceiling or other surface, taking advantage of the Coandă effect
To create low-velocity air movement in the occupied portion of room
Accomplish the above while producing the minimum amount of noise
When possible, dampers, extractors, and other flow control devices should not be placed near diffusers' inlets (necks), either not being used at all or being placed far upstream. They have been shown to dramatically increase noise production.
This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.
A fan is a powered machine used to create a flow of air. A fan consists of a rotating arrangement of vanes or blades, generally made of wood, plastic, or metal, which act on the air. The rotating assembly of blades and hub is known as an impeller, rotor, or runner. Usually, it is contained within some form of housing, or case. This may direct the airflow, or increase safety by preventing objects from contacting the fan blades. Most fans are powered by electric motors, but other sources of power may be used, including hydraulic motors, handcranks, and internal combustion engines.
A fan coil unit (FCU), also known as a Vertical Fan Coil-Unit (VFC), is a device consisting of a heat exchanger (coil) and a fan. FCUs are commonly used in HVAC systems of residential, commercial, and industrial buildings that use ducted split air conditioning or with central plant cooling. FCUs are typically connected to ductwork and a thermostat to regulate the temperature of one or more spaces and to assist the main air handling unit for each space if used with chillers.
Ducts are conduits or passages used in heating, ventilation, and air conditioning (HVAC) to deliver and remove air. The needed airflows include, for example, supply air, return air, and exhaust air. Ducts commonly also deliver ventilation air as part of the supply air. As such, air ducts are one method of ensuring acceptable indoor air quality as well as thermal comfort. A duct system is also called ductwork. Planning (laying out), sizing, optimizing, detailing, and finding the pressure losses through a duct system is called duct design.
In this study the influence of tip leakage on the performance of a small-scale fan is evaluated through computational fluid dynamics. ANSYS CFX Release 18.1 is employed for the numerical simulations, the results are extracted, analyzed and compared to the ...
2017
, , , ,
This paper presents preliminary results of an experimental study on the occurrence and development of the upper part-load instability in a reduced-scale Francis turbine. The study includes draft tube pressure measurements, high-speed flow visualization, an ...
IOP PUBLISHING LTD2021
This study reports the results from an experimental comparison of two cooling systems. The studied systems were a radiant cooling system (radiant ceiling panels and mixing ventilation), and a combined radiant and convective cooling system (combination of a ...