Effect of intelligent antennas on radio system planning and on mitigation

Smart antennas have been recently applied to improve the capacity and the performance of second generation wireless mobile communication systems. In general, smart antennas reduce the effects of multipath fading and improve the signal-to-noise-plus-interference ratio (SNIR). Additional advantages such as channel capacity increase in urban areas, coverage extension in urban areas and spectrum efficiency in general can be obtained with the aid of smart antennas at the base station. Drawbacks are the cost, and both hardware and software complexity. Smart antennas promise a clear advantage in multi-service traffic scenario in comparison with non-adaptive antenna techniques. It is generally accepted that the adaptive antennas technique will be a key enable for the success of the European third generation mobile communication system known as Universal Mobile Telecommunication System (UMTS). The first part of this thesis presents two types of smart antenna systems: switched beam antennas and adaptive arrays. It introduces statistical models for them and investigates the performance measures of cellular radio systems with and without smart antennas deployed at base stations. Employing Monte-Carlo methodology, a tool has been developed to analyze the interference between two different systems that share the same geographical area and have neighboring frequency channels. The statistical smart antennas model has been used to verify the mitigation of the interference compared with others antennas used at the base station. These simulations have been done for TDMA, FDMA and CDMA systems. Wireless communication operating at different frequencies on the non-ionizing radiation (NIR) region of the electromagnetic spectrum has greatly increased in the last few decades, with important benefits for the population. These include mobile communication, such as cellular telephone systems. However, the radiated electromagnetic field levels increased substantially in areas where people may stay during long periods each day. This may result in long-term exposure to the population. International guidelines and standards were developed aiming at protecting the population, and limiting the maximum radiation produced. The methods used by regulation authorities to evaluate the field levels at places of sensitive use yield very conservative results. They need thus to be refined prior to the introduction of adaptive antennas. In the second part of the thesis, a 3D ray tracing tool is developed to predict the propagation for real scenarios using UMTS systems. This tool takes into account 3D radiation diagrams and multipath propagation. It was used in real scenarios to compare the real field levels with the levels obtained by the approximate methods defined by the regulation standards. Finally, this tool was used to predict the field levels in a scenario containing smart antennas. Scenario not foreseen in the method described in the standards.

Biological samples studied by optical nanospectroscopy

Johanna Generosi

The different parts of the electromagnetic spectrum result in diverse effects upon interaction with matter: according to the wavelength, the radiation has energy appropriate for the excitation of a specific physical process. X-rays can be used as a tool to analyze the structure of matter since their wavelength is comparable with the interatomic distances. Infrared light is in the spectral region that excites molecular vibrations and is employed to investigate the chemical composition of a material. Visible radiation can study the optical properties of a sample, such as the fluorescence and the absorbance, and provide a chemical fingerprint when the inelastically scattered light is detected. In this thesis work these light sources are used in diverse experimental approaches to study structured biological specimens, resulting in a detailed chemical and physical characterization at the atomic and molecular scale. Conventional spectroscopy is often not enough sensitive and spatially resolved to detect specific elements or domains in a sample. The need of imaging objects on increasingly finer scales and spatially localize specific molecules, brought to combine infrared, visible and Raman spectroscopy with scanning near-field microscopy giving rise to a powerful nanospectroscopic tool used to perform simultaneous topographical measurements and optical/chemical characterizations with subwavelength resolution, overcoming the diffraction limit of light. Our study combines X-ray diffraction and reflectivity with optical nanospectroscopy to investigate the order and clustering of lipid bilayers, the interaction between solid-supported membranes and embedded alamethicin peptides, the optical and chemical properties of hippocampal neuron cells and the trafficking mechanism of specific neuron receptors.

EPFL2009

Design of novel radiating elements for SATCOM phased arrays in Ku-Band

Baptiste Fernand Hornecker

The present thesis deals with the design of a planar antenna array for the communication between a civil aircraft (Dassault's Falcon) and an Inmarsat satellite. The final goal is to provide high speed Internet access in X/Ku-Band (8-12GHz / 12-18GHz), and possibly even in K/Ka- Band (18-27GHz / 17-40GHz). The study starts with the Ku-Band only, then evolves towards the transmission band and finishes with their Ka-Band counterparts. The main constraint of the thesis is that the final result should be a low profile antenna that will be easy to integrate below the fuselage of an aircraft. At the same time, the antenna has to provide a beam steering mechanism in order to track the position of the targetted satellite while the aircraft is moving. The usual way to achieve it is to implement some dedicated electronic chips below each radiating element of array. Dassault Aviation has its own alternate and more mechanical oriented solutions. Since the communication system is intended for top-notch business jets produced in small series, cost is not here a decisive criterion. This thesis assumes the existence of the beam-steering system and concentrates on a proof of concept and careful design of the antenna elements that will constitute the final array. They have to satisfy tight constraints in terms of size, return loss, mutual coupling with neighbors, efficiency, radiation pattern and dual circular polarization quality. Printed multilayer antennas have been retained as the best candidates, and themain parts of the thesis have been dedicated to their study. The thesis concludes with the presentation of an apparently completely unrelated and independant topic, namely the simulation of nanoscale 2D planar structures based on Graphene. The rationale for this last chapter is to provide a prospective study of the use of Graphene to create a variable capacitance. This component is always needed in the beamforming network of reconfigurable and scanning arrays. Our laboratory is developing a deep knowledge of the electromagnetic properties of Graphene-based devices and these varicaps could lead to very interesting applications in high frequencies, once the Graphene technology has definitely progressed. Thanks to electrostatics Green's functions, a variable capacitor based on Graphene has been simulated, and a Quantumeffect -the Quantum capacitance of Graphene- has been successfully tackled from a numerical point of view.

EPFL2016

Antennas for CubeSat Communication

Miroslav Veljovic

CubeSats are a type of small satellites (< 500 kg) that weigh several kilograms and consist of multiple Units (U) measuring 100 × 100 × 113.5 mm3. CubeSats emerged as a low-cost alternative to conventional large satellites, and have since demonstrated capabilities for communication, Earth observation, technology demonstration and many other. The primary goal of CubeSats, as it is the case with any miniaturized satellite, is to reduce the cost of orbital deployment. CubeSats are commonly launched as a secondary payload on large launch vehicles. One or several satellites are placed in a dedicated deployment system, which typically accommodates three CubeSat Units. The deployment system strictly limits the dimensions of any features on the CubeSat surface. CubeSat antennas perform the same functions as antennas on conventional satellites, such as telemetry and command, communication, navigation or inter-satellite links (ISL). However, most traditional antennas for small satellites are not suitable for CubeSats due to the profile constraints of the deployment system. Two approaches for antenna design are generally adopted. In the first, one or several low-profile antennas are placed on the CubeSat exterior. In the second, deployable antenna structures are used if the CubeSat platform does not offer sufficient dimensions. At low frequencies, the additional space is required to achieve a good radiation efficiency, whereas at high frequencies an increased antenna aperture provides a high gain. This thesis describes several antenna geometries, both low-profile and deployable, which enable several communication aspects of an Internet-of-Things (IoT) constellation of 3U CubeSats in the Low Earth Orbit (LEO). The main novelty of the proposed solutions is in their electromagnetic performance, as opposed to most CubeSat antenna designs where the mechanical design is the main achievement. The presented antennas succeed to exhibit a wide bandwidth or a specified radiation under strict size constraints. The thesis presents several wideband aperture-coupled patch antennas for TT&C and data downlink in S and X bands. A thoroughly investigated shielded-stripline feeding structure enables a wideband circular polarization (CP) with a unidirectional radiation, and demonstrates capabilities such as interference suppression of adjacent frequencies and efficient CubeSat integration. Patch-antenna arrays in L band are then presented, which radiate several independent beams for the capacity increase of an IoT machine-to-machine (M2M) communication system. The high permittivity of the antenna substrates lead to a strong coupling to the 3U CubeSat structure, emphasizing the importance of the antenna placement. Finally, different configurations of high-gain fixed-beam reflectarrays (RA) and transmitarrays (TA) are for the first time proposed for CubeSat ISL LEO communications in K band. Two novel unit cells are presented for RA and TA antennas, based on coupled loops and aperture-coupled patches, respectively. An axially corrugated CP horn antenna is designed as the feeding element for the arrays. A prototype of this antenna is fabricated using additive manufacturing in aluminum. The performance of all antennas, presented in this thesis, is validated by agreements between the calculation and 3D-simulation results and the VNA and anechoic-chamber measurements of several prototypes.