A hybrid on-chip optomechanical transducer for ultrasensitive force measurements

Nanoscale mechanical oscillators(1) are used as ultrasensitive detectors of force(2), mass(3) and charge(4). Nanomechanical oscillators have also been coupled with optical and electronic resonators to explore the quantum properties of mechanical systems(5). Here, we report an optomechanical transducer in which a Si3N4 nanomechanical beam(6,7) is coupled to a disk-shaped optical resonator made of silica on a single chip. We demonstrate a force sensitivity of 74 aN Hz(-1/2) at room temperature with a readout stability better than 1% at the minute scale. Our system is particularly suited for the detection of very weak incoherent forces, which is difficult with existing approaches because the force resolution scales with the fourth root of the averaging time(8). By applying dissipative feedback(9) based on radiation pressure, we significantly relax this constraint and are able to detect an incoherent force with a force spectral density of just 15 aN Hz(-1/2) (which is 25 times less than the thermal noise) within 35 s of averaging time (which is 30 times less than the averaging time that would be needed in the absence of feedback). It is envisaged that our hybrid on-chip transducer could improve the performance of various forms of force microscopy(8,10-12).

Ultra low quantum decoherence nano-optomechanical systems

Mohammadjafar Bereyhi

Thermal motion of a room-temperature mechanical resonator typically dominates the quantum backaction of its position measurement. This is a longstanding barrier for exploring cavity optomechanics at room temperature. In order to enter the quantum regime of the optomechanical interaction, we need to be in the "backaction-dominated" regime, where we can study the limits of quantum measurement and how to circumvent them. To create a system which can enter the quantum regime, the optomechanical transducer has to satisfy certain criteria. A quantum-enabled optomechanical system consists of an optical cavity and a mechanical resonator with ultra low quantum decoherence, which are strongly coupled to each other via the optomechanical interaction.High stress silicon nitride has enabled nanomechanical resonators with exceptionally low dissipation at room temperature via several soft-clamping techniques. Achieving high optomechanical coupling to these coherent nanobeams results in high optomechanical cooperativities, thus alleviating the thermal motion barrier for room temperature quantum optomechanics. Monolithic integration of high-Q nanobeam resonators with optical cavities has been limited to doubly-clamped nanobeams due to the complexity of the device fabrication and long device sizes required for conventional soft-clamping using phononic crystals. In addition, the previous demonstrations of such systems showed limited optomechanical couplings thus a limited single photon cooperativity.I present the design, fabrication and characterization of three different classes of nanomechanical resonators clamp-tapered, fractal-like, and polygon resonators, which support perimeter modes, with Q factors exceeding 3 billion at room temperature and their optical readout using an integrated nearfield nano-optomechanical transducer using high stress silicon nitride. Our transducer features a one-dimensional Fabry-Perot optical cavity integrated with a high-Q nanomechanical resonator. The Fabry-Perot optical cavity is formed by patterning two photonic crystal reflectors on a silicon nitride waveguide designed for high-Q optical modes. Our approach allows individual optimization of optical and mechanical resonators, while maintaining a high optomechanical coupling rate due to large optomechanical mode overlap. Our best performing devices show on-chip optomechanical transducers with single photon cooperativities as high as 123 with mechanical quality factor of 120 million at room temperature. The developed system is of great interest to the optomechanics and sensing community. In quantum optomechanics, it will serve as a platform for quantum feedback control of the nanomechanical resonators to achieve motional ground state of a macroscopic resonator and generation of squeezed light at room temperature. Owing to their record value mechanical quality factors, the room temperature force sensitivity of our highest Q perimeter modes is on par with atomic force microscopy cantilevers at millikelvin temperature.Complete documentation of a nanofabrication process is the key to its reproducibility. Process-specific details of the fabrication techniques are usually missing in journal publications. To bridge this gap, I developed NanoFab-net.org. An online open-access tool that allows sharing process-specific fabrication reports, extracting the metadata and obtaining a unique digital object identifier (DOI) for each report.

EPFL2022

Ultralow-dissipation optomechanical resonators on a chip

Tobias Kippenberg, Albert Schliesser

Cavity-enhanced radiation-pressure coupling of optical and mechanical degrees of freedom gives rise to a range of optomechanical phenomena, in particular providing a route to the quantum regime of mesoscopic mechanical oscillators. A prime challenge in cavity optomechanics has been to realize systems that simultaneously maximize optical finesse and mechanical quality. Here we demonstrate, for the first time, independent control over both mechanical and optical degrees of freedom within the same on-chip resonator. The first direct observation of mechanical normal mode coupling in a micromechanical system allows for a quantitative understanding of mechanical dissipation. Subsequent optimization of the resonator geometry enables intrinsic material loss limited mechanical Q-factors, rivalling the best values reported in the high megahertz frequency range, while simultaneously preserving the resonators' ultrahigh optical finesse. As well as providing a complete understanding of mechanical dissipation in microresonator-based optomechanical systems, our results provide a promising setting for cavity optomechanics.

2008

Quantum limits on measurement and control of a mechanical oscillator

Vivishek Sudhir

The precision measurement of position has a long-standing tradition in physics. Cavendish's verification of the universal law of gravitation using a torsion pendulum, Perrin's confirmation of the atomic hypothesis via the precise measurement of the Brownian motion, and, the verification of the mechanical effect of electromagnetic radiation, all belong to this classical heritage. Quantum mechanics posits that the measurement of position results in an uncertain momentum; an idea developed to full maturity within the context of interferometric searches for gravity waves. Over the past decade, standing at the confluence of quantum optics and nanomechanics, cavity optomechanics has emerged as a powerful platform to study the quantum limits of position measurements. The subject of this thesis is the precision measurement of the position of a nano-mechanical oscillator, the fundamental limits of such measurements, and its relevance to measurement-based feedback control. The nano-mechanical oscillator is coupled to light confined in an optical micro-cavity via radiation pressure. The fluctuations in the position of the oscillator are transduced onto the phase of the light, while quantum fluctuations in the amplitude of the light leads to a disturbance in the momentum of the oscillator. We perform an interferometric position measurement with a sensitivity that is 10^5 times below what is required to resolve the zero-point motion of the oscillator, constituting the most precise measurement of thermal motion yet. The resulting disturbance -- measurement back-action -- is observed to be commensurate with the uncertainty principle, leading to a 10% contribution to the total motion of the oscillator. The continuous record of the measurement (performed in a 4 K cryogenic environment) furnishes the ability to resolve the zero-point motion of the oscillator within its decoherence rate - the necessary condition for measurement-based feedback control of the state of the oscillator. Using the measurement record as error signal, the oscillator is cooled towards its ground state, resulting in a factor 10^4 suppression of its total (thermal and back-action) motion, to a final occupation of 5 phonons on average. Measurements generally proceed by establishing correlations between the system being measured and the measuring device. For the class of quantum measurements employed here - continuous linear measurements - these correlations arise due to measurement back-action. These back-action-induced correlations appear as correlations between the degrees of freedom of the measuring device. For interferometric position measurements, quantum correlations are established between the phase and amplitude of the light. In a homodyne measurement, they lead to optical squeezing, while in a heterodyne measurement, they appear as an asymmetry in the sidebands carrying information about the oscillator position. Feedback is used to enhance sideband asymmetry, a first proof-of-principle demonstration of the ability to control quantum correlations using feedback. In the regime where amplified vacuum noise dominates the feedback signal, the disappearance of sideband asymmetry visualises a fundamental limit of linear feedback control. Using a homodyne detector, we also characterise these quantum correlations manifested as optical squeezing at the 1% level.