Seismic response of a 4 storey building with reinforced concrete and unreinforced masonry walls

In Switzerland many new residential buildings are designed as mixed structures with unreinforced masonry (URM) walls and reinforced concrete (RC) walls while existing URM structures are often retrofitted by replacing selected URM walls by RC walls. The lateral bracing system of the resulting structure consists therefore of URM walls and some RC walls. All walls are coupled by RC slabs and/or masonry spandrels. Since the seismic performance of such mixed structures– despite being very common in design and retrofit– is still not well understood, a shake-table test on a four-storey RC-URM wall structure was performed at the TREES laboratory of the EUCENTRE in Pavia (Italy). In this paper we present the details of the shake-table test and discuss its results. We compare the observed behaviour to that generally observed for URM structures and conclude on the effect of adding slender RC walls to URM buildings in terms of damage evolution. The force-displacement response of the structure is presented, its response for the two loading directions discussed and different methods for computing the base shear force compared.

Development of a displacement-based design approach for modern mixed RC-URM wall structures

Katrin Beyer, Alessandro Paparo

The recent re-assessment of the seismic hazard in Europe led for many regions of low to moderate seismicity to an increase in the seismic demand. As a consequence, several modern unreinforced masonry (URM) buildings, constructed with reinforced concrete (RC) slabs that provide an efficient rigid diaphragm action, no longer satisfy the seismic design check and have been retrofitted by adding or replacing URM walls with RC walls. Of late, also several new construction projects have been conceived directly as buildings with both RC and URM walls. Despite the widespread use of such construction technique, very little is known about the seismic behaviour of mixed RC-URM wall structures and codes do not provide adequate support to designers. The aim of the paper is therefore to propose a displacement-based design methodology for the design of mixed RC-URM edifices and the retrofit of URM buildings by replacing or adding selected URM walls with RC ones. The article describes also two tools developed for estimating important quantities relevant for the displacement-based design of structures with both RC and URM walls. The tools are (i) a mechanical model based on the shear-flexure interaction between URM and RC walls and (ii) an elastic model for estimating the contribution of the RC slabs to the overturning moment capacity of the system. In the last part of the article the proposed design method is verified through non-linear dynamic analyses of several case studies. These results show that the proposed design approach has the ability of controlling the displacement profile of the designed structures, avoiding concentration of deformations in one single storey, a typical feature of URM wall structures.

Techno-Press2015

Structural Response of R-UHPFRC - RC Composite Members Subjected to Combined Bending and Shear

Talayeh Noshiravani

The addition of a thin overlay of Ultra-High Performance Fibre Reinforced Concrete (UHPFRC) to Reinforced Concrete (RC) members is an emerging technique to strengthen and protect existing structures and to design durable new structures. Combining UHPFRC with closely spaced, small-diameter steel rebars in Reinforced UHPFRC (R-UHPFRC) layers improves the UHPFRC's strain hardening behaviour. For reasons of practicality, R-UHPFRC layers are cast or glued (in the case of prefabricated elements) on top of RC members, thus changing the latter into R-UHPFRC - RC composite members. The high strength and deformation capacity of R-UHPFRC elements make them a suitable external flexural reinforcement for RC members over intermediate supports, e.g., bridge decks and slabs or beams in buildings. Over reinforcement of RC beams and slabs with tensile flexural reinforcement can result in their shear failure at either a lower resistance or deformation than the associated values for member failure in flexure. A comprehensive experimental program was conducted to study the flexure-shear behaviour of R-UHPFRC - RC composite beams. The program comprises two test series on cantilever beams and continuous beams. The test parameters include shear span-depth ratio (a/d), the amount of transverse reinforcement ( ρν), the amount of longitudinal reinforcement, and the strength and bond condition of the R-UHPFRC rebars. The experimental results reveal the different failure modes of R-UHPFRC - RC composite members and the contribution of the R-UHPFRC elements to the member resistance, ductility and capacity to redistribute the internal stress. It was shown that in R-UHPFRC - RC beams with ribbed rebars and a shear span to depth ratio greater than 2.5 the stresses are carried by beam action. Depending on the degree of longitudinal reinforcement, all but two of the beams with 3.0≤a/d≤3.4 and ρν≤0.17 had a flexure-shear failure; the rest failed in flexure. The flexure-shear failure of the composite beams was at an approximately equal rotation level as their RC reference beam but at a resistance 2.3 times that of the RC beam. This is due to (1) the debonding interface zone between the elements that allows the R-UHPFRC - RC beams to rotate more freely and (2) the out-of-plane resistance of the R-UHPFRC element that contributes to the shear resistance. The internal flow of forces and the structural response of composite members strongly depend on the bond condition between the R-UHPFRC and RC, the UHPFRC and its rebars, as well as the concrete and its rebars. Cracking of the concrete along the interface zone causes bond reduction, i.e., softening of the shear connection, between the two elements. In presence of high shear stresses and diagonal flexure-shear cracks, interface zone softening is observed between the elements prior to the maximum resistance, while UHPFRC is strain hardening. The cause of this softening behaviour is the prying action due to the relative rotational movement of the RC rigid bodies separated by the flexure-shear cracks. Static and kinematic solutions of the theory of plasticity for RC beams are extended to predict the collapse load of R-UHPFRC - RC composite beams at the ultimate limit state. A mechanical model for predicting the structural response of composite beams is proposed. In combination with truss models, the concept of an R-UHPFRC - RC plastic hinge is introduced to calculate the force-displacement response of composite beams. The failure criterion based on the collapse mechanisms (kinematic solutions) sets the limit of the force-displacement response. The model is corroborated by the experimental results. This model provides a tool for analysis of RC members reinforced with an added tensile R-UHPFRC element.

EPFL2012

Dynamic testing of a four-storey building with reinforced concrete and unreinforced masonry walls: Prediction, test results and data set

Katrin Beyer, Sarah Petry, Marco Tondelli

This paper presents the results of a series of shake-table tests on a half-scale, four-storey building with reinforced concrete (RC) and unreinforced masonry (URM) walls. Due to the lack of reference tests, the seismic behaviour of such mixed structures is poorly understood. The test unit was subjected to several runs of increasing intensity yielding performance states between minor damage and near collapse. Before the test, the expected peak table accelerations leading to different limit states were estimated using the capacity spectrum method, and the predicted values corresponded rather well to actual sustained accelerations. Next to these analyses, the paper describes the test unit, instrumentation and input motion, and comments on the response of the mixed structure in terms of damage evolution and global response quantities, such as force-displacement response and drift and acceleration profiles. The raw and post-processed data sets are made publically available, and all relevant information with regard to data organisation is described in an appendix to this paper. The test serves therefore as a benchmark for the validation of numerical models of such mixed structures. The project aims at providing a foundation for the development of seismic design and assessment methods of mixed structures, which are currently not covered by structural codes, including Eurocode 8.

Springer Verlag2015

Structural Response of R-UHPFRC - RC Composite Members Subjected to Combined Bending and Shear

Talayeh Noshiravani

EPFL2012