An Optically Transparent Iron Nickel Oxide Catalyst for Solar Water Splitting

Sunlight-driven water splitting to produce hydrogen fuel is an attractive method for renewable energy conversion. Tandem photoelectrochemical water splitting devices utilize two photoabsorbers to harvest the sunlight and drive the water splitting reaction. The absorption of sunlight by electrocatalysts is a severe problem for tandem water splitting devices where light needs to be transmitted through the larger bandgap component to illuminate the smaller bandgap component. Herein, we describe a novel method for the deposition of an optically transparent amorphous iron nickel oxide oxygen evolution electrocatalyst. The catalyst was deposited on both thin film and high-aspect ratio nanostructured hematite photoanodes. The low catalyst loading combined with its high activity at low overpotential results in significant improvement on the onset potential for photoelectrochemical water oxidation. This transparent catalyst further enables the preparation of a stable hematite/perovskite solar cell tandem device, which performs unassisted water splitting.

Amorphous molybdenum sulfides as hydrogen evolution catalysts

Xile Hu, Carlos Gilberto Morales Guio

Providing energy for a population projected to reach 9 billion people within the middle of this century is one of the most pressing societal issues. Burning fossil fuels at a rate and scale that satisfy our near-term demand will irreversibly damage the living environment. Among the various sources of alternative and CO2-emission-free energies, the sun is the only source that is capable of providing enough energy for the whole world. Sunlight energy, however, is intermittent and requires an efficient storage mechanism. Sunlight-driven water splitting to make hydrogen is widely considered as one of the most attractive methods for solar energy storage. Water splitting needs a hydrogen evolution catalyst to accelerate the rate of hydrogen production and to lower the energy loss in this process. Precious metals such as Pt are superior catalysts, but they are too expensive and scarce for large-scale applications. In this Account, we summarize our recent research on the preparation, characterization, and application of amorphous molybdenum sulfide catalysts for the hydrogen evolution reaction. The catalysts can be synthesized by electrochemical deposition under ambient conditions from readily available and inexpensive precursors. The catalytic activity is among the highest for nonprecious catalysts. For example, at a loading of 0.2 mg/cm2, the optimal catalyst delivers a current density of 10 mA/cm2 at an overpotential of 160 mV. The growth mechanism of the electrochemically deposited film catalysts was revealed by an electrochemical quartz microcrystal balance study. While different electrochemical deposition methods produce films with different initial compositions, the active catalysts are the same and are identified as a “MoS2+x” species. The activity of the film catalysts can be further promoted by divalent Fe, Co, and Ni ions, and the origins of the promotional effects have been probed. Highly active amorphous molybdenum sulfide particles can also be prepared from simple wet-chemical routes. Electron transport is sometimes slow in the particle catalysts, and an impedance model has been established to identify this slow electron transport. Finally, the amorphous molybdenum sulfide film catalyst has been integrated onto a copper(I) oxide photocathode for photoelectrochemical hydrogen evolution. The conformal catalyst efficiently extracts the excited electrons to give an impressive photocurrent density of −5.7 mA/cm2 at 0 V vs RHE. The catalyst also confers good stability.

American Chemical Society2014

Coupling of electrocatalysts to photoabsorbers for solar fuels production

Carlos Gilberto Morales Guio

The direct transformation of sunlight into fuels and chemicals has attracted considerable attention for the potential impact on the storage of solar energies at large scales and the reduction of CO2 emissions. More than 80% of our current global energy consumption comes from the burning of non-renewable fossil fuels which produces enormous quantities of CO2 and contributes to global warming. We believe today that the key to reduce our dependence on exhaustible natural resources and limit the emission of greenhouse gases is the transition to CO2-free renewable energy sources. However, harvesting of energy from renewable sources (i.e. solar, wind, tidal) is intermittent and the deployment of devices for their transformation into useful forms of energy (i.e. electricity, chemicals, fuels, biomass) in a global scale is conditioned upon the improvement in efficiency of the energy storage mechanisms. A promising approach to store energy is the use of sunlight to drive the production of hydrogen fuel from water. Hydrogen produced from water and sunlight can be transformed back to electricity on demand or be used to generate mechanical energy in cars to power the transportation industry. The oxidation of hydrogen generates useable energy and at the same time exhaust clean, carbon-free water as the only product. Therefore, the production of hydrogen using a renewable energy source in an efficient and inexpensive device has the potential to discourage the continued use of fossil fuels and improve our environment. The viability of any mechanism for the storage of sunlight as fuel will depend on the reduction of energy penalties during the transformation process. Electrocatalysts are advanced materials that bring into one active site electrons and molecules in the appropriate orientation to lower activation energy barriers, accelerate rate of transformations and improve overall efficiencies for chemical reactions. The best catalysts for water splitting are precious metals such as Pt, Ir and Ru, which show superior rates of reaction at low overpotentials. However, these noble metals are too expensive and scarce for large scale applications. This thesis summarizes our recent research in the preparation, characterization, and application of Earth-abundant electrocatalysts for solar water splitting. Although in the last decade a great number of efficient and inexpensive electrocatalysts have been reported, methods for the deposition of these materials on the surface of photoabsorbers are rarely reported. This work shows various simple and scalable techniques for the deposition of hydrogen and oxygen evolving electrocatalysts on the surface of photocathodes and photoanodes, respectively. Surface-protected photocahodes were activated for solar hydrogen production in alkaline conditions with MoS2+x, Ni-Mo and Mo2C. A novel method for the deposition of an optically transparent amorphous iron nickel oxide oxygen evolution electrocatalyst is also reported. The catalyst was deposited on both thin film and high-aspect ratio nanostructured hematite photoanodes. The low catalyst loading combined with its high activity at low overpotential results in significant improvement on the onset potential for photoelectrochemical water oxidation. This transparent catalyst further enables the preparation of a stable hematite/perovskite solar cell tandem device, which performs unassisted water splitting.

EPFL2016

A Hierarchical 3D TiO2/Ni Nanostructure as an Efficient Hole-Extraction and Protection Layer for GaAs Photoanodes

Peer Fischer, Michael Graetzel, Hyeonho Jeong

Photoelectrochemical (PEC) water splitting is a promising clean route to hydrogen fuel. The best-performing materials (III/V semiconductors) require surface passivation, as they are liable to corrosion, and a surface co-catalyst to facilitate water splitting. At present, optimal design combining photoelectrodes with oxygen evolution catalysts remains a significant materials challenge. Here, we demonstrate that nickel-coated amorphous three-dimensional (3D) TiO(2)core-shell nanorods on a TiO(2)thin film function as an efficient hole-extraction layer and serve as a protection layer for the GaAs photoanode. Transient-absorption spectroscopy (TAS) demonstrated the role of nickel-coated (3D) TiO(2)core-shell nanorods in prolonging photogenerated charge lifetimes in GaAs, resulting in a higher catalytic activity. This strategy may open the potential of utilizing this low-cost (3D) nanostructured catalyst for decorating narrow-band-gap semiconductor photoanodes for PEC water splitting devices.