Structural Reversibility and Nickel Particle stability in Lanthanum Iron Nickel Perovskite-Type Catalysts

Davide Ferri, Debora Foppiano, Andre Heel, Oliver Kröcher
Wiley-V C H Verlag Gmbh, 2017
Journal paper

Abstract

Perovskite-type oxides have shown the ability to reversibly segregate precious metals from their structure. This reversible segregation behavior was explored for a commonly used catalyst metal, Ni, to prevent Ni sintering, which is observed on most catalyst support materials. Temperature-programmed reduction, X-ray diffraction, X-ray absorption spectroscopy, electron microscopy, and catalytic activity tests were used to follow the extent of reversible Ni segregation. LaFe1-xNixO3-delta (0

Official source

https://infoscience.epfl.ch/record/229603?ln=en

About this result

This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.

Related concepts

Related publications

Transition metal clusters on h-BN/Rh(111)

Hamed Achour

The main aim of this dissertation is to study the catalytic aspects of very small transition metal clusters supported on h-BN/Rh(111). The catalytic reactions of interest were ammonia synthesis and CO oxidation on mass selected and soft landed iron and platinum clusters, respectively. A special focus was devoted to the investigation of the stability of these very small clusters on h-BN before and after the reaction. It was found that Pt7 clusters soft landed at room temperature with an energy of 1.2 eV per atom and annealed to 700 K exhibit Smoluchowski ripening. Above this temperature, these clusters undergo partial intercalation between the h-BN monolayer and the Rh(111). The intercalation initiates at 900 K and becomes more pronounced when the clusters are annealed under gas reaction conditions. A high catalytic activity was observed when the Pt catalyst remains supported on h-BN. In this case, the reaction starts at 480 K and follows Langmuir-Hinshelwood mechanism. However, the catalytic activity strongly reduces when the Pt clusters undergo partial intercalation. Nevertheless, in this case the reaction starts at only 380 K, revealing a reduction by 100 K in the Pt poisoning as a result of substrate effect and charge redistribution. In a second trail, the cluster-h-BN interaction was studied through h-BN irradiation with Pt clusters, at room temperature, within an energy window of 30-416 eV/atom. The results show that even irradiation at 30 eV/atom can lead to entire non thermal intercalation of the clusters. The energetic Pt clusters were found to be site selective as they settle only under the h-BN wires, in contrast to soft landed Pt7 clusters that were found to settle at the side edge of the h-BN depressions. After being exposed to irradiated Pt clusters, at an energy above 100 eV/atom, the h-BN layer starts to display visual cavity-type defects. These defects, induced by collision, disappeared after annealing to 600 K under gas reaction leaving behind an h-BN with no visual defects. CO temperature desorption spectroscopy (TDS) indicates that the intercalated Pt is inactive towards CO oxidation due to h-BN screening. Subsequently, we were able to produce a catalyst system made of soft-landed Pt/h-BN/intercalated Pt/Rh(111) using a combination between soft and energetic Pt deposition with which a reduction by 100 K in CO poisoning was obtained. Finally, ammonia synthesis was conducted on soft landed Fe clusters, supported on h-BN/Rh(111) and deposited at 100 K under Ultra High Vacuum (UHV). Scanning tunneling microscopy (STM) displays two imaging states of the as deposited clusters; a ring state surrounding h-BN depression which disappears above 300 K and a dot like structure. The Fe clusters are found to grow by Ostwald ripening after annealing to 600 K and above this temperature, they endure partial intercalation. It was found that, in the presence of iron, the nitrogen reaction gas experienced an exchange with the nitrogen species forming the h-BN layer. TPR (Temperature Programmed Reduction) of N

_2

with hydrogen revealed that nitrogen reduction occurs at 620 K under high vacuum following the Haber-Bosch method. The detection of reaction intermediates NH and NH

_2

together with desorbed atomic nitrogen, during ammonia synthesis, confirms that NH

_3

formation involves the stepwise hydrogenation of adsorbed nitrogen.

EPFL2017

Mixed ionic electronic conducting perovskite materials have been receiving considerable attention for the application of oxygen separation membranes. These membranes have potential to be integrated in industrial processes that require pure oxygen and to provide advantages considering economical and environmental aspects. The used perovskite materials can accommodate a high concentration of disordered oxygen vacancies and provide high oxygen permeation flux in the presence of an oxygen partial pressure gradient. However, the materials with high oxygen flux are observed to have low chemical and mechanical stability, originating from oxygen vacancy formation and reduction of the B-site transition metal ion. Based on the fact that the stability of the materials at reducing pO2 is dependent on the redox stability of the B-site cation, a partial substitution of the B-site transition metal with a more stable cation is considered in this thesis to improve the stability of the base perovskite oxide. The approach used for the identification of the suitable material based on the host composition La0.5Sr0.5FeO3-δ (LSF) was to first explore the B-site substituting elements in terms of their effect on the thermal expansion and the isothermal expansion measured during the atmosphere change from air to argon. The elements Al, Cr, Zr, Ga, Ti, Sn, Ta, In, V, and Mg were used for 10 or 20% substitution of Fe. The isothermal expansion of the host material was decreased by substitution, which was attributed to decreased amount of oxygen vacancy formation as it was evidenced later by TGA of chosen compositions. As a result, the compositions substituted with higher valence ions (particularly, 20% Ti4+, LSFTi2, and 10% Ta5+, LSFTa1) were identified as the least expanding materials in isothermal conditions. The effect of substitution was further characterized extensively including structural, mechanical, and oxygen transport properties. The oxygen vacancy (VO••) concentration changes induced by substitution of Fe were reflected in unit cell sizes of heat-treated samples under argon atmosphere. The increase in the unit cell size was attributed to the isothermal expansion due to B-site reduction and lowered to half in case of substituted LSFTi2 and LSFTa1 compared to the host material LSF. Similar trends were observed for interrelated properties such as the coefficient of thermal expansion, isothermal expansion, and the actual amount of oxygen vacancies formed under argon at 900°C, all of which were higher for LSF. The mechanical properties of LSF, LSFTi2, and LSFTa1 were characterized at room temperature. The Young's modulus and the bending strength of the materials were in the same range (141-147 GPa and ∼120 MPa, respectively) while the fracture toughness of the LSF sample was improved by Ti and especially Ta substitution. The fractography of the samples provided evidence that the several LSF samples showed extended cracks possibly related to residual stresses forming during cooling, due to non-equilibrated oxygen stoichiometry across the sample. The potential step measurements showed that the chemical diffusion and the surface exchange coefficients measured during oxidation of the samples were higher than the ones measured during reduction of the samples. The tendency was reversed at lowered pO2 along with the decrease of both coefficients. The influence of B-site substitution on both coefficients was not substantial. The oxygen permeation flux of LSF, LSFTi2, and LSFTa1 was measured under air/argon gradient on planar membranes. The permeation rates of the membranes with thicknesses close to 1 mm were considered to be limited by surface exchange kinetics at temperatures above 875°C. The permeation rate of LSF was decreased (from 0.2 µmolcm-2s-1) to its third by Ti and Ta additions. The permeation rate of Ti and Ta-substituted samples showed a drop around 875°C, keeping a similar activation energy at lower and higher temperature regions. Oxygen vacancy ordering in the perovskite structure was given as a possible explanation, which provided explanation for the slow equilibrium in the lower temperature region. Tubular membranes of LSF and LSFTi2 (0.47 mm and 0.36 mm thick, respectively) and a planar LSFTa1 membrane were characterized using an air/(Ar-CH4) gradient. The measurements conducted using pure Ar on the lean-side provided the possibility to compare the thickness dependence of the permeation. In agreement with the previous observations, the permeation of the materials at and above 900°C was independent of the thickness, therefore, surface exchange limited. Stability under reducing atmospheres was increased by substitution. The LSF membrane failed shortly after the introduction of CH4 to the system, while LSFTi2 survived 5% CH4 and its oxygen permeation was improved substantially by a factor of 14. LSFTa1 membrane was measured with pure CH4 and the permeation was increased by a factor of 9, reaching 0.7 µmolcm-2s-1 at 900°C. The membrane operated stably over 2000h with pure CH4, 1000h. A slow degradation of 3.7% per 1000h was observed at 1000°C, most probably due to cation migration. The compositions identified as a result of B-site substitution screening were effective in improving the stability of the materials without extensive loss of the oxygen permeation rate. Ta-substituted material was shown to be promising with its long-term stability as a partial oxidation membrane.

EPFL2008

Molecular hydrogen is a promising candidate to replace fossil fuels as the energy carrier. Hydrogen does not exist in its molecular form on earth and must therefore be generated, starting from hydrogen-rich compounds. Water would be a renewable resource for hydrogen. It can be split into oxygen and hydrogen. Water splitting, however, needs electrical energy. If this energy is produced from renewable resources, such as solar or wind power, water splitting would be a sustainable and green process. One key step in water splitting is the reduction of protons to form hydrogen. To achieve a high efficiency in this reaction, catalysts are required. This dissertation is devoted to the development of hydrogen evolution catalysts that are made of earth-abundant and inexpensive materials. First, transition metal complexes of tetrathiotungstate and tetrathiomolybdate were studied as potential homogeneous catalysts for hydrogen evolution in organic or aqueous solutions (chapter 1). The redox activity of these complexes was investigated by cyclic voltammetry in the absence and presence of an acid in organic solutions. The first reduction peak of (Pr4N)2[Ni(MoS4)2] became more intense and was shifted to less negative potentials upon addition of an acid, e.g. p-cyanoanilinium tetrafluoroborate. This was considered as a sign for catalytic proton reduction. Electrolysis of a solution containing (Pr4N)2[Ni(MoS4)2] and an acid produced hydrogen. However, the complex turned out to be a precursor of the real catalytically active species, which was deposited on the working electrode’s surface during the electrochemical experiment. Consecutive cyclic voltammetric scans were found to be a good method to deposit the catalytically active film in a controllable manner from an aqueous solution of (Pr4N)2[Ni(MoS4)2]. Furthermore, a catalytically active film could be deposited from a solution of MoS42-, i.e. in the absence of Ni2+. Chapter 2 describes the investigation and characterization of films made using MoS42- as the precursor. The films consist of amorphous molybdenum sulfide. They are efficient hydrogen evolution catalysts in water. The films were characterized by XPS and electron microscopy. Whereas the pre-catalysts could be MoS3 or MoS2, the active form of the catalysts was identified as amorphous MoSx, with x close to 2. Significant geometric current densities were achieved at low overpotentials (e.g., ca. 15 mA/cm2 at η = 200 mV) using these catalysts. The catalysis was compatible with a wide range of pH values. The current efficiency for hydrogen production was quantitative. A Tafel slope of 39 mV/dec was observed, suggesting a rate-determining Heyrovsky step. The turnover frequency per active site was estimated.

EPFL2012