Lead Halide Perovskite Quantum Dots to Enhance the Power Conversion Efficiency of Organic Solar Cells

The facile synthesis, solution-processability, and outstanding optoelectronic properties of emerging colloidal lead halide perovskite quantum dots (LHP QDs) makes them ideal candidates for scalable and inexpensive optoelectronic applications, including photovoltaic (PV) devices. The first demonstration of integrating CsPbI3 QDs into a conventional organic solar cell (OSC) involves embedding the LHP QDs in a donor-acceptor (PTB7-Th:PC71BM) bulk heterojunction. Optimizing the loading amount at 3 wt %, we demonstrate a power conversion efficiency of 10.8 %, which is a 35 % increase over control devices, and is a record amongst hybrid ternary OSCs. Detailed investigation into the mechanisms behind the performance enhancement shows that increased light absorption is not a factor, but that increased exciton separation in the acceptor phase and reduced recombination are responsible.

Solid state nanocrystalline titanium oxide photovoltaic cells

The dye solar cell, is a novel photoelectrochemical solar cell presenting unique advantages, as the use of low cost materials and the potential simplicity of manufacturing. However, a liquid electrolyte is actually required for the transport of the photogenerated positive charges. A major breakthrough is the replacing of the liquid electrolyte by a solid-state hole conducting material – the aim of this work. First, the metal/TiO2 junction was investigated, with either silver or gold as rectifying contact. Sensitization was demonstrated, as action spectra were measured using different dyes. The evaporated metal could not enter the pores of the nanocrystalline TiO2 to contact all the dye molecules, hence only low photovoltaic performances were obtained. Furthermore, these metal/TiO2 junctions showed a high sensitivity to humidity and to forward bias polarization. The use of an electrically conducting polymer, poly(bithiophene), was studied in a metal/polymer junction and in TiO2/polymer devices with flat and nanocrystalline TiO2 electrodes. The photoelectric characterizations indicated that electrochemically reduced poly(bithiophene) was able to inject electrons into TiO2, i.e. sensitizing TiO2, and it acted as a hole conducting layer. Short-circuit current densities of 2-3 mA/cm2 were measured at an irradiation of 1.2 W/cm2. The open-circuit voltages were in the 250-350 mV range, depending on the light intensity and temperature. The use of a transparent hole conducting material, CuI, which is a wide bandgap p-type semiconductor, was demonstrated in a nanocrystalline junction made of highly porous sensitized TiO2 and solution-cast CuI. A short-circuit current of 1 mA/cm2 was achieved under one sun simulated light; the open-circuit voltage was 600 mV and the light-to-power conversion efficiency was 0.3 %. The peak quantum efficiencies of 8 % in the UV, and 3 % in the visible, showed that the nanocrystalline junction was working inefficiently, probably due to the poor electrical contact between the TiO2 nanocrystallites and the CuI crystals. Furthermore, the sensitizer was not tuned to inject holes into the valence band of CuI. As conclusion, a controlled-capillary pore based sensitized device is suggested. In this concept, all the internal surface of the TiO2 electrode coated with sensitizer is contacted with the transparent hole conducting layer, hence improving the photovoltaic properties of the device.

EPFL1996

Interface engineering in solid-state dye-sensitized solar cells

Jessica Krüger

Dye-sensitised nanocrystalline solar cells are currently subject of intense research in the framework of renewable energies as a low-cost photovoltaic device. In particular dye-sensitised cells based on spiro-MeOTAD have gained attention as promising approach towards an organic solid-state solar cell. However, the efficiency in such dye-sensitised solid-state solar devices (SSD) was so far only ca. 10 % of the values reported at AM1.5 for the classical dye-sensitised solar cell with an electrolyte hole transporting medium (DSSC). The objective of the present work is to study the limitations that emerge from the exchange of the electrolyte by the solid-state system and that oppose photovoltaic photon-to-electron conversion as high as for the DSSC. Interfacial charge recombination is an important loss mechanism in dye-sensitised solar cells. This is particularly true for SSD, as the solid hole-transporting medium is less efficient in screening of internal fields which assist recombination. A variety of strategies were tested in the SSD to minimise interfacial charge recombination. The most promising approach was the blending of the hole-transporting medium with tert.-butylpyridine (tBP) and lithium ions. Optical and electrochemical techniques, such as nanosecond laser spectroscopy, impedance spectroscopy and photovoltaic characterisation measurements, were used to study the impact of the additives on the SSD. Both lithium ions as well as tBP were found to increase the open circuit potential of the SSD. At the same time tBP was found to considerably lower the current output. The interaction of the additives was studied and their concentration in the spiro-MeOTAD medium optimised. The doping of the spiro-MeOTAD film, which was intended to support the hole transport, was found to enhance interfacial recombination significantly. The morphological properties of the TiO2, in particular layer thickness, particle size and film porosity, play a more important role in the SSD than in the DSSC. Penetration of the hole conductor into the TiO2 pores and electron diffusion length are coupled to these properties. As a result the light harvesting cannot be controlled at will via the TiO2 film thickness and the active surface area for dye adsorption. An enhanced light harvesting for thin TiO2 layers offers advantages for the charge transport and the formation of the interpenetrating network. The dye uptake in presence of silver ions was found to increase the dye loading and to significantly improve the device performance of thin TiO2 layer devices. The mechanism of this simple dye modification technique was studied by a variety of spectroscopic techniques. From spectroscopic evidence it is inferred that the silver is binding to the sensitiser via the ambidentate thiocyanate, allowing the formation of ligand-bridged dye complexes. The beneficial influence of the silver ions on the photovoltaic performance was not limited to the application of the standard N3 dye nor to the spiro-MeOTAD. SSDs were furthermore studied by frequency resolved techniques. Intensity modulated photocurrent spectroscopy (IMPS) and intensity modulated photovoltage spectroscopy (IMVS) were performed over a wide range of illumination intensities. The IMPS and IMVS responses provide information about charge transport and electron-hole recombination processes respectively. For the range of light intensities investigated, the dynamic photocurrent response appears to be limited by the transport of electrons in the nanocrystalline TiO2 film rather than by the transport of holes in the spiro-MeOTAD. The diffusion length of electrons in the TiO2 was found to be 4.4 μm. This value was almost independent of the light intensity as a consequence of the fact that the electron diffusion coefficient and the rate constant for electron-hole recombination both increase in the same way with light intensity but with opposite sign. The results of this work provide for a substantial improvement of the overall photovoltaic performance compared to earlier results for this type of SSD. However, this study reveals also that high conversion efficiencies as are measured for DSSC are not likely to be reachable with the spiro-MeOTAD system due to the significantly slower charge transport in the spiro-MeOTAD compared to the electrolyte redox mediator.

EPFL2003

Strategies to Optimizing Dye-Sensitized Solar Cells

Sophie Wenger

Dye-sensitized solar cells (DSCs) constitute a novel class of hybrid organic-inorganic solar cells. At the heart of the device is a mesoporous film of titanium dioxide (TiO2) nanoparticles, which are coated with a monolayer of dye sensitive to the visible region of the solar spectrum. The role of the dye is similar to the role of chlorophyll in plants; it harvests solar light and transfers the energy via electron transfer to a suitable material (here TiO2) to produce electricity — as opposed to chemical energy in plants. DSCs are fabricated of abundant and cheap materials using inexpensive processes (e.g. screen-printing) and are likely to be a significant contributor to the future commercial photovoltaic technology portfolio. The work conducted during this thesis aimed at optimizing the DSC using three different strategies: The use of versatile organic sensitizers for stable and efficient DSCs, the study of tandem device architectures in combination with other solar cells to harvest a larger fraction of the solar spectrum, and the development of a validated optoelectric model of the DSC. Organic donor-π-acceptor dyes are an interesting alternative to the standard metal-organic complexes used in DSCs. Efficient photovoltaic conversion and stable performance could be demonstrated with three classes of donor systems, namely diphenylamine, difluorenylaminophenyl, and π-extended tetrathiafulvalene. The highest conversion efficiencies were obtained with a difluorenylaminophenyl donor system (η = 8.3 % with a volatile electrolyte and η = 7.6 % with a solvent-free ionic liquid, which was a new record for organic dyes at the time of publication). Surprisingly, efficient regeneration of the oxidized dye by the I-/I3- redox mediator was found with the π-extended tetrathiafulvalene system, even though the thermodynamic driving force was as low as 150 mV. So far driving forces of 300-500 mV had been regarded as necessary for efficient regeneration of the dye cation. Also, important structure-property relationships pertaining to the recombination of electrons with the electrolyte and to the stability of the device could be identified (i.e. effect of linear vs. branched structure, linker length, and moieties used). The power conversion efficiency of solar cells can be extended beyond the limit for a single cell (∼ 30 %) by using multiple cells with different optical gaps in a tandem device. DSCs and chalcopyrite Cu(In,Ga)Se2 (CIGS) solar cells have complementary optical gaps and are thus suitable systems for integration in a tandem device. It was shown that a monolithic DSC/CIGS tandem device has the potential for increased efficiency over a mechanically stacked device due to increased light transmission to the bottom cell, and a monolithic DSC/CIGS device with an initial efficiency of η = 12.2 % was demonstrated. The degradation of the devices — induced by the corrosion of the CIGS cell in contact with the I-/I3- redox mediator — could be retarded with a protective thin conformal ZnO/TiO2 oxide layer coated on the CIGS cell by atomic layer deposition. Finally, an experimentally validated optical and electrical model of the DSC has been developed to assist the optimization process, which is predominantly conducted by empirical means in the DSC research community. The optical model allows to accurately calculate the internal quantum efficiency of devices, i.e. the ratio of extracted electrons to absorbed photons by the dye, a crucial and so far difficult to determine characteristic. Intrinsic parameters — like injection efficiency, electron diffusion length, or distribution of trap states in the TiO2 — can be extracted from experimental steady-state and time-dependent data with the electric model. The model allows to make a comprehensive and quantitative loss analysis of the different optical and electric loss channels in the DSC. The model has been implemented with a graphical user interface for straightforward usage. All three optimization strategies — organic dyes, tandem architecture, and device modeling — developed during this thesis make a valuable contribution to the development and commercialization of inexpensive and high efficiency DSCs. They enable a comprehensive view of the system and pave the way for a systematic analysis and reduction of losses, which has been the ultimate route to success for several established photovoltaic technologies.

EPFL2010