Enhancing the operational flexibility of thermal power plants by coupling high-temperature power-to-gas

The increasing penetration of intermittent renewable power challenges the stability of the electrical grid, thus coal power plants are usually required to extend the operation range by reducing the minimum load. This work proposes a concept of coupling solid-oxide cell stack based power-to-gas with coal power plants to allow for dual functions of (1) storing excess renewable electricity and (2) reducing the minimum load of coal power plants by combustion stabilization with oxygen-rich air from power-to-gas. The performance and operating strategy of such an integrated plant are evaluated with detailed off-design characteristics of the considered coal power plants. The results show that the integration of power-to-gas affects the distribution of the heat absorbed by radiative and convective heat exchangers in the boiler, stabilizes coal combustion, and reduces the superheat degree of live/reheated steam. It allows the power plant for operating at a significantly low load of down to 22% of the nominal load, compared with 40% before the coupling; meanwhile, a very limited penalty is caused with the plant efficiency reduced from 34.4% down to 34.1% (with 13% of the normalized power-to-gas capacity). Minimizing the power-to-gas contribution to the accommodated renewable power is advantageous for a minimal CO2 emission; nevertheless, maximizing the power-to-gas contribution with the coal power plant at high load allows for a maximal system efficiency.

Thermo-Economic Optimisation of Solar Tower Thermal Power Plants

James Spelling

Amidst a backdrop of rapidly increasing world-wide electricity demand, solar thermal power generation shows great potential for supplying the electricity needs of numerous countries in the Sun-belt regions of the world. In these regions, the absence of significant biomass, hydrological or geothermal reserves makes solar thermal power the most promising solution for meeting that most fundamental of demands: energy. Amidst the different options available for harnessing the Sun’s power, solar thermal technologies have been shown capable of producing electricity at the most economically viable rates [32]. However, all currently existing solar thermal power plants have been based around the use of Rankine, or steam turbine, cycles which are limited in the efficiencies they can achieve. In order to make better use of the Sun’s energy, higher efficiency cycles should be used. With their high concentration ratios, solar thermal power tower systems are amongst the best options for making use of the Sun’s potential. As the energy delivery temperature of central receiver systems is higher, they harness the solar radiation at a higher exergy level [4]. This higher temperature also opens the road to the use of more advanced thermodynamic cycles. Hybrid fossil-fuel – solar systems are also imaginable [13], as the energy delivery temperature is compatible with standard gas turbine cycles. Hybrid systems can help mitigate the requirements of thermal energy storage, as well as reducing the perceived risk when investing in new solar technology, which stimulates research and development, as well as providing employment. Recent developments in the field of high temperature volumetric receivers [10] along with rock- based packed-bed storage systems have opened up an interesting possibility. High temperature receivers allow the use of higher-efficiency combined-cycle setups, whereas packed-bed units offer the possibility of cheap storage. Larger storage volumes allow pure-solar systems to extend their power production into the night, making hybrid options less attractive. This is compounded by the common practice of guaranteeing a preferred tariff for electricity sales from pure-solar sources With this in mind, a complete dynamic model of a power plant based on the pure-solar concept has been elaborated. The performance of the setup is evaluated over a range of days, using solar insolation profiles obtained from satellite data. In order to examine different design options and their impact on the performance of the power plant, a multi-objective, thermo-economic optimisation of both the power plant superstructure and operating conditions was performed using the new, dynamic models. By means of an evolutionary algorithm [17], a family of Pareto-optimal points were obtained, representing the trade-off between increased power plant efficiency, and lower levelised energy costs. Through use of optimisation, it was shown that exergetic efficiencies in the region of 21-27% can be achieved, for relatively low power outputs of between 3 and 11 MWe. These configurations correspond with levelised electricity costs in the region of 14-21 UScts/kWhe. In most regions, the use of solar power is encouraged by the guarantee of a preferential tariff for electricity sales from renewable sources. Sale of electricity at a price of around 24 UScts/kWhe [32] should therefore be imaginable, ensuring the economic viability of solar thermal power tower systems. It can be concluded that, when properly designed, solar thermal power plants based on combined cycles are both economically and thermodynamically promising. By raising the efficiency of the plant, the size of the solar collector field is diminished, increasing the otherwise low energy densities of solar power systems. By reducing the levelised electricity costs, solar thermal power plants become more economically viable, accelerating their construction and thus, hopefully, reducing our dependence on fossil-fuels.

2009

Preliminary Study of a Solar Trough/Tower Power Plant

Jorge López Moreno

The possibility of combining both the advantages of a solar tower thermal power plant and of a solar parabolic trough power plant could be interesting from an energetic point of view as well from an economic point of view. The preliminary study of this combination feasibility is the goal of this project. The study of the project viability consist first of all on the modeling of the trough system, the energy balance of the parabolic troughs will be established at first. Secondly, and choosing a perfect solar day simulating a day when the solar radiation is rather stable, with no cloudy periods along the day, the power available from the trough plant can be calculated. Once we have estimated the power that we can introduce into the cycle of the tower plant, the main issue consists on how and where it is better to use this energy in the cycle. Several possibilities seem to be interesting a priori, however a more detailed study of each one is to be done in order to get to the most economic and efficient layout. The work related to the tower thermal power plant will be done taking as starting point the master thesis of James Spelling, who did an incredible work in this field and whose work will be a valuable help to continue the research on the proposed concept in this project of combining two plants, tower and trough. The main advantage of the tower design compared to the parabolic trough design is the higher temperature. As it will be explained further, thermal energy at higher temperature can be converted more efficiently, the exergy efficiency is better. In terms of storage, the high temperature results in a cheaper and a more efficient storage system. Nevertheless, the set up of the field of heliostats is more complex than the set up of the parabolic trough lines even though the area for a trough plant must be previously flattened. The lower temperature level that entails an inconvenient itself for a parabolic trough power plant may become an advantage when combining both types of concentrating solar power plants. If the results are positive enough that it seems interesting to combine both types of power plants, another step forward will be done towards the use of the sun energy as a renewable source thus making it a more interesting choice for power generation. Sun potential has already shown as an important technology not only at the present time but also in the future. Commercial solar plants have already achieved levelized energy costs around 12-15 UScts/kWh, and the potential for cost reduction is expected to follow this trend even further, to costs as low as 5 UScts/kWh. In addition the taxes imposed for the non-green power should make even more interesting the use of concentrating solar power plants. The requirements of high beam normal radiation lead to a limited amount of suitable places where the implantation of this technology is possible. However many places exist on Earth where the conditions are perfectly adapted, we talk about regions such as United States (the country with more carbon dioxide emissions in the world), some regions in Mexico, North Africa, India, Australia, northeastern Brazil and some locations around the Mediterranean, especially in the south of Spain. The challenge is therefore set for a change in our energy production scheme.

2010

Triple-mode grid-balancing plants via biomass gasification and reversible solid-oxide cell stack: Concept and thermodynamic performance

Chengzhou Li, Tzu-En Lin, François Maréchal, Maria del Mar Perez Fortes, Jan Van Herle, Ligang Wang, Yumeng Zhang

Biomass-to-electricity or -chemical via power-to-x can be potential flexibility means for future electrical grid with high penetration of variable renewable power. However, biomass-to-electricity will not be dispatched frequently and becomes less economically-beneficial due to low annual operating hours. This issue can be addressed by integrating biomass-to-electricity and -chemical via ‘‘reversible’’ solid-oxide cell stacks to form a triple-mode grid-balancing plant, which could flexibly switch among power generation, power storage and power neutral (with chemical production) modes. This paper investigates the optimal designs of such a plantconcept with a multi-time heat and mass integration platform considering different technology combinationsand multiple objective functions to obtain a variety of design alternatives. The results show that increasing plant efficiencies will increase the total cell area needed for a given biomass feed. The efficiency difference among different technology combinations with the same gasifier type is less than 5% points. The efficiency reaches up to 50%–60% for power generation mode, 72%–76% for power storage mode and 47%–55% for power neutral mode. When penalizing the syngas not converted in the stacks, the optimal plant designs interact with the electrical and gas grids in a limited range. Steam turbine network can recover 0.21–0.24 kW electricity per kW dry biomass energy (lower heating value), corresponding to an efficiency enhancement of up to 20%points. The difference in the amounts of heat transferred in different modes challenges the design of a common heat exchange network.