Diffusion-Bonding Between Strands and Modeling of Splices of Nb3Sn Rutherford Cables

Pierluigi Bruzzone, Nikolay Bykovskiy, Kamil Sedlák
IEEE-INST ELECTRICAL ELECTRONICS ENGINEERS INC, 2022
Journal paper

Abstract

Particle accelerators foresee the use of Nb3Sn in the next generation of dipole magnets. A common design strategy is to grade the coil, i.e., to optimize the quantity of superconductor in the turns with respect to the magnetic field intensity. As a consequence, the magnet winding consists of different Nb3Sn Rutherford cables that must be connected in series through splices having sufficiently low electrical resistance. In previous works, the Swiss Plasma Center designed and tested in the SULTAN facility bent diffusion-bonded splices for wind-and-react dipole magnets to develop an internal splice, i.e., to be embedded in the winding pack. The global splice resistance met the requirement. Such splices consist of hundreds of parallel resistive diffusion-bonded spots, located at the cross-over of the two overlapped Rutherford cables. In this manuscript, samples of single diffusion-bonded spots are manufactured and electrically tested to assess their resistance. The results are in line with the expectations, despite the scattering of the experimental data. Moreover, the network of strands and spots is recreated in an electrical model to interpret the resistance-field characteristic assessed from the measurements of splices between Nb3Sn Rutherford cables.

Official source

https://infoscience.epfl.ch/record/291526?ln=en

About this result

This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.

Related concepts

Related publications

Preliminary Tests of Soldered and Diffusion-Bonded Splices Between Nb3Sn Rutherford Cables for Graded High-Field Accelerator Magnets

Pierluigi Bruzzone, Mithlesh Kumar, Davide Uglietti

High-field accelerator magnets of the next generation will require coil grading in order to decrease the amount of superconductor and hence the magnet cost. The joints between Nb3Sn conductor grades must have low electrical resistance (

IEEE-INST ELECTRICAL ELECTRONICS ENGINEERS INC2019

Test of the MF-CICC Conductor Designed for the 12-T Outsert Coil of the HFML 45-T Hybrid Magnet

Pierluigi Bruzzone, Kamil Sedlák, Boris Stepanov

A 45-T hybrid magnet is being built at the High Field Magnet Laboratory of the Radboud University in Nijmegen, The Netherlands. The hybrid magnet consists of a 12-T cable-in- conduit-conductor (CICC) Nb 3Sn superconducting outsert and a 33-T resistive insert magnet. To verify the CICC design, a thorough testing has been completed in the SULTAN facility at Swiss Plasma Center, EPFL in Villigen (Switzerland) for the medium- grade conductor of the outsert. In two test campaigns, the dc cable performance (current-sharing temperature, critical current), the ac loss, and the conductor's performance stability during cyclic loading and after one warmup and cooldown cycle have been investigated. Two different cable layouts were tested-one with a very short twist pitch (STP) and the second one with a long twist pitch (LTP) cabling pattern. As both conductors were made of the same Nb 3Sn strand and underwent the same heat treatment and sample preparation procedure, the effect of the twist pitch on the ac loss and on the dc performance with respect to cyclic loading could be reliably evaluated. The test results show that both cable layouts are actually very robust. The cable could withstand 2000 load cycles and the warmup and cooldown cycle without any significant degradation of the dc performance, and even the overloading at BI product (field multiplied by current) approximately two times larger than those foreseen during magnet operation did not lead to a big performance change. Small differences between the STP and LTP options have been observed, indicating that the STP conductor withstands high electromagnetic loads better than the LTP one.

2016

, , , , , ,

We present the pre-concept design of the European DEMO Magnet System, which has successfully passed the DEMO plant-level gate review in 2020. The main design input parameters originate from the so-called DEMO 2018 baseline, which was produced using the PROCESS systems code. It defines a major and minor radius of 9.1 m and 2.9 m, respectively, an on-axis magnetic field of 5.3 T resulting in a peak field on the toroidal field (TF) conductor of 12.0 T. Four variants, all based on low-temperature superconductors (LTS), have been designed for the 16 TF coils. Two of these concepts were selected to be further pursued during the Concept Design Phase (CDP): the first having many similarities to the ITER TF coil concept and the second being the most innovative one, based on react-and-wind (RW) Nb3Sn technology and winding the coils in layers. Two variants for the five Central Solenoid (CS) modules have been investigated: an LTS-only concept resembling to the ITER CS and a hybrid configuration, in which the innermost layers are made of high-temperature superconductors (HTS), which allows either to increase the magnetic flux or to reduce the outer radius of the CS coil. Issues related to fatigue lifetime which emerged in mechanical analyses will be addressed further in the CDP. Both variants proposed for the six poloidal field coils present a lower level of risk for future development. All magnet and conductor design studies included thermal-hydraulic and mechanical analyses, and were accompanied by experimental tests on both LTS and HTS prototype samples (i.e. DC and AC measurements, stability tests, quench evolution etc.). In addition, magnet structures and auxiliary systems, e.g. cryogenics and feeders, were designed at pre-concept level. Important lessons learnt during this first phase of the project were fed into the planning of the CDP. Key aspects to be addressed concern the demonstration and validation of critical technologies (e.g. industrial manufacturing of RW Nb3Sn and HTS long conductors, insulation of penetrations and joints), as well as the detailed design of the overall Magnet System and mechanical structures.

2022

, , , , , ,

2022