Publication

Heat transfer of uncoated and nanostructure coated commercially micro-enhanced refrigeration tubes under pool boiling conditions

John Richard Thome
2023
Journal paper
Abstract

The heat transfer performance of commercially produced micro-enhanced tubes with and without a nanocoating was investigated under pool boiling of saturated refrigerant. These multiscale enhancements were on the outside of 19 mm horizontal copper tubes heated by water to determine the effectiveness of this multiscale enhancement technique on industrially relevant tubes and geometry. The tubes tested were a plain tube roughened by sandpaper, a low finned GEWA-KS tube and two micro-enhanced re-entrant cavity tubes, the GEWA-B5 and EHPII. The tubes were tested in R134a at saturation temperatures of 5 degrees C and 25 degrees C across a range of heat fluxes from 20 kW/m2 to 100 kW/m2 under pool boiling conditions. The nanocoating applied to the tubes produced a forest of copper oxide nanostructures on the surface, increasing wickability of the surface. A Scanning Electron Microscopy showed that copper oxide nanocoatings coated all micro-enhanced tubes evenly without impeding the surface features or significantly blocking the re-entrant cavities. For the uncoated tubes in pool boiling, the heat transfer coefficients of the EHPII was up to 519 % greater than those of the plain roughened tube, the GEWA-B5 was up to 539 % higher than the roughened tube and the GEWA-KS was at best 64 % higher than those of the plain roughened tube. Increases in the saturation temperature to 25 degrees C produced minor improvements in heat transfer coefficients. The application of the copper oxide nanocoating resulted in generally decreased heat transfer performance by approximately 40 % on average compared to the uncoated tubes, with the GEWA-B5 tube the worst affected. Degradation of the heat transfer is thought on plain surfaces to be due to the flooding of nucleation sites, while re-entrant cavity style enhanced surfaces were thought to experience degraded sensible and latent heat transfer due to impeded flow in the microstructure capillary channel, as bubbles were noted to be trapped in the channels. It is recommended that the heat transfer at much higher heat flux ranges be explored for possible HTC enhancement.

About this result
This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.
Related concepts (32)
Heat pipe
A heat pipe is a heat-transfer device that employs phase transition to transfer heat between two solid interfaces. At the hot interface of a heat pipe, a volatile liquid in contact with a thermally conductive solid surface turns into a vapor by absorbing heat from that surface. The vapor then travels along the heat pipe to the cold interface and condenses back into a liquid, releasing the latent heat. The liquid then returns to the hot interface through capillary action, centrifugal force, or gravity and the cycle repeats.
Heat exchanger
A heat exchanger is a system used to transfer heat between a source and a working fluid. Heat exchangers are used in both cooling and heating processes. The fluids may be separated by a solid wall to prevent mixing or they may be in direct contact. They are widely used in space heating, refrigeration, air conditioning, power stations, chemical plants, petrochemical plants, petroleum refineries, natural-gas processing, and sewage treatment.
Heat
In thermodynamics, heat is the thermal energy transferred between systems due to a temperature difference. In colloquial use, heat sometimes refers to thermal energy itself. An example of formal vs. informal usage may be obtained from the right-hand photo, in which the metal bar is "conducting heat" from its hot end to its cold end, but if the metal bar is considered a thermodynamic system, then the energy flowing within the metal bar is called internal energy, not heat.
Show more
Related publications (143)

Plasmoid drift and first wall heat deposition during ITER H-mode dual-SPIs in JOREK simulations

Mengdi Kong

The heat flux mitigation during the thermal quench (TQ) by the shattered pellet injection (SPI) is one of the major elements of disruption mitigation strategy for ITER. It's efficiency greatly depends on the SPI and the target plasma parameters, and is ult ...
Iop Publishing Ltd2024

Multiscale enhancement of refrigerant falling film boiling by combining commercially enhanced tubes with nanostructures

John Richard Thome

Multiscale surface structures offer the opportunity to combine the heat transfer enhancement provided by microscale structures with the dryout benefits provided by some nanostructures, which is particularly attractive for falling film evaporators, who have ...
Oxford2023

Beam radiation penetration in particle b e ds for heat transfer modeling of a centrifugal solar particle receiver

Evan Fair Johnson, Serdar Hiçdurmaz

This article describes a study of beam radiation striking particle beds of randomly packed, spherical par-ticles. The current study is focused on concentrating solar power receivers which use solid particles as a heat transfer medium, but results are appli ...
PERGAMON-ELSEVIER SCIENCE LTD2023
Show more
Related MOOCs (15)
SES Swiss-Energyscope
La transition énergique suisse / Energiewende in der Schweiz
SES Swiss-Energyscope
La transition énergique suisse / Energiewende in der Schweiz
Thermodynamics
Ce cours complète le MOOC « Thermodynamique : fondements » qui vous permettra de mettre en application les concepts fondamentaux de la thermodynamique. Pour atteindre cet objectif, le Professeur J.-P
Show more

Graph Chatbot

Chat with Graph Search

Ask any question about EPFL courses, lectures, exercises, research, news, etc. or try the example questions below.

DISCLAIMER: The Graph Chatbot is not programmed to provide explicit or categorical answers to your questions. Rather, it transforms your questions into API requests that are distributed across the various IT services officially administered by EPFL. Its purpose is solely to collect and recommend relevant references to content that you can explore to help you answer your questions.