Publication

Process-Induced Structures of Injection-Molded High-Density Polyethylene-Combining X-ray Scattering and Finite Element Modeling

Related publications (36)

Graph Chatbot

Chat with Graph Search

Ask any question about EPFL courses, lectures, exercises, research, news, etc. or try the example questions below.

DISCLAIMER: The Graph Chatbot is not programmed to provide explicit or categorical answers to your questions. Rather, it transforms your questions into API requests that are distributed across the various IT services officially administered by EPFL. Its purpose is solely to collect and recommend relevant references to content that you can explore to help you answer your questions.

UV-cured Epoxy for Adhesion in Steel Reinforced Thermoplastic Composites

Basile Golaz

This work addresses the development of composite materials that contain metallic load-bearing cords with the aim of combining outstanding mechanical performance with added functionality, including electrical conductivity, data transmission, and temperature ...

EPFL2012

, , ,

Background: Articular surfaces reconstruction is essential in total shoulder arthroplasty. Because of the limited glenoid bone support, thin glenoid component could improve anatomical reconstruction, but adverse mechanical effects might appear. Methods: Wi ...

Elsevier2012

Novel Fe supported catalysts were prepared by immobilizing iron species on commercial polyethylene via three different methods: (1) acidic pre-treatment of the polyethylene followed by impregnation in aqueous Fe(NO3)(3), (2) TiO2 photo-catalytic pre-treatm ...

2011

Polymer micro-molding of femtosecond laser micromachined substrates

Yves Bellouard

Micro-molding can be used for the cost-effective fabrication of elements such as active or passive components in MEMS devices, hydrophobic surfaces, cell-growth scaffolds or optical components such micro-lens arrays and gratings. This method is also partic ...

SPIE-INT SOC OPTICAL ENGINEERING2011

, , ,

Wear of polyethylene is associated with aseptic loosening of orthopaedic implants and has been observed in hip and knee prostheses and anatomical implants for the shoulder. The reversed shoulder prostheses have not been assessed as yet. We investigated the ...

2009

Preparation, stabilization and characterization of TiO2 on thin polyethylene films (LDPE): Photocatalytic applications

Albert Renken, Philippe Buffat, Lioubov Kiwi, Juan Kiwi, Andrzej Kulik, Danièle Laub

An innovative way to fix preformed nanocrystalline TiO2 on low-density polyethylene film (LDPE-TiO2) is presented. The LDPE-TiO2 film was able to mediate the complete photodiscoloration of Orange II using about seven times less catalyst than a TiO2 suspens ...

2007

Development of pressure sensors by powder technology

Peter Ryser, Sebastien Martinerie, Thomas Maeder, Caroline Jacq, Sonia Vionnet Menot

Thick film deposition of conductive, dielectric and resistive pastes on ceramic membranes is a cost effective technique to manufacture piezoresistive pressure sensors. Thick-film resistors consist of a percolating network of conductive oxide nanoparticles ...

2007

Tailoring of the practical adhesion between polyethylene and galvanised steel

Véronique Michaud, Gabrielle Pax

Abstract—The practical adhesion of maleic anhydride grafted polyethylene (MAH-PE) to galvanised steel was studied using 3-point flexure tests, before and after hydrothermal ageing. Before bonding, the electro-galvanised steel was treated with γ -aminopropy ...

2006

Tubular La0.7Ca0.3Fe0.85Co0.15O3-delta Perovskite Membranes, Part I: Preparation and Properties

Jan Van Herle, Stefan Diethelm

Dense tubular self-supporting La0.7Ca0.3Fe0.85 Co0.15O3-δperovskite membranes were prepared by thermoplastic extrusion. The rheological behavior of the ceramic mixture was studied. Non-deformed tubes o ...

2006

Procede non isothermique de fabrication de parties composites creuses

Martyn Douglas Wakeman, Pascal Vuilliomenet

A process for making hollow composite structures or vessels which includes the steps of: A) heating a mixture of thermoplastic matrix and reinforcing fibres wrapped over a rigid or semi-rigid thermoplastic liner or bladder above the melting point of the th ...

2005