Publications related to The influence of through-thickness reinforcement geometry and pattern on delamination of fiber-reinforced composites: Part II - Modeling

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Marie Estelle Solange Violay, Corentin Jean-Marie Rémi Noël, Barnaby Padraig Fryer

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Tara Habibi, Landolf-Giosef-Anastasios Rhode-Barbarigos

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Numerical investigation of two-dimensional Mode-II delamination in composite laminates

Thomas Keller, Anastasios Vassilopoulos, Congzhe Wang

Existing standards for delamination tests on composite materials typically employ one-dimensional (1D) beam specimens. However, such specimens may not represent real delamination scenarios in composite structures, where cracks tend to propagate in two dime ...

Elsevier Sci Ltd2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Dataset for "Complexity of crack front geometry enhances toughness of brittle solids"

John Martin Kolinski, Chenzhuo Li, Xinyue Wei

This data package supports the publication 'Complexity of crack front geometry enhances toughness of brittle solids' by Xinyue Wei, Chenzhuo Li, Cían McCarthy, and John M. Kolinski Nature physics (2024) - https://doi.org/10.1038/s41567-024-02435-x DOI: 1 ...

Zenodo2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

An adaptive phase field approach to 3D internal crack growth in rocks

Alexandra Roma Larisa Kushnir, Tao Xu, Michael Heap

Modeling the 3D internal crack under compression entails complex fracture mechanics (mode I-II-III fracture), resulting in substantial computational costs and challenges in characterizing fracture morphology characterization for Phase Field Method (PFM) si ...

2024