Publications associées à Appareillage électrique

Positive Streamer Initiation in SF6/CO2 Based on Zener's Field Ionization

In this study, experiments were performed to measure the inception and breakdown voltages of SF6/CO2 mixed gases with varying mixing ratios at two different pressures (1 and 2 bar). Using the preliminary data obtained from the experiments, a 3D particle mo ...

IEEE-INST ELECTRICAL ELECTRONICS ENGINEERS INC2023

Vacuum Circuit Breaker Closing Time Key Moments Detection via Vibration Monitoring: A Run-to-Failure Study

Olga Fink, Gaëtan Michel Frusque

Circuit breakers (CBs) play an important role in modern society because they make the power transmission and distribution systems reliable and resilient. Therefore, it is important to maintain their reliability and to monitor their operation. A key to ensu ...

2022

Partial discharge localization using time reversal: Application to gas insulated switchgear

Farhad Rachidi-Haeri, Marcos Rubinstein, Hamidreza Karami

Gas-insulated switchgear (GIS) are some of the most reliable and most expensive equipment that are nowadays used in power systems. Condition monitoring of the power system equipment can help operators detect defects like partial discharges (PDs) early, pre ...

Elsevier2022

Metal-wire-embedded alumina insulating material using micro- and nanoscale 3D printing for surface flashover mitigation in a vacuum

Guang-Yu Sun

A micro- and nanoscale 3D printing technique is applied to fabricate a functional insulating material that mitigates surface discharge in a vacuum based on microscopic electron multipactor suppression. The proposed alumina ceramic insulator design consists ...

2022

Partial discharge localization using time reversal: application to power transformers and gas-insulated substations

Marcos Rubinstein, Mohammad Azadifar, Farhad Rachidi-Haeri, Amirhossein Mostajabi, Hamidreza Karami

A method for locating one or multiple partial discharge sources in a power transformer or a Gas-Insulated Substation, whereby the partial discharges emit electromagnetic and acoustic waves, the method comprising recording a signal corresponding to the wave ...

2021

Three-Dimensional FDTD-Based Simulation of Induced Surges in Secondary Circuits Owing to Primary-Circuit Surges in Substations

Farhad Rachidi-Haeri, Marcos Rubinstein, Akiyoshi Tatematsu

Currently, plenty of sensitive electronic devices are installed in secondary circuits in substations and power plants. Electronic devices may malfunction and become damaged owing to electromagnetic disturbances caused mainly by lightning surges. To protect ...

2021

Ultra High Voltage Switch for Bidirectional DC-DC Converter Driving Dielectric Elastomer Actuator

Yves Perriard, Yoan René Cyrille Civet, Morgan Almanza, Lucas Pniak

Specific applications, such as dielectric elastomer actuators (DEAs) or electroactive polymers, require to switch voltage levels exceeding the ratings of existing semiconductor devices. In low power application, reversible flyback are widely used to supply ...

2020

Swiss Competence Center on Energy Research FURIES - Overview and Contributions in the Area of Power Electronics and Smart Grids

Mario Paolone, Drazen Dujic, Farhad Rachidi-Haeri, Milan Utvic, Reza Razzaghi, Stefan Milovanovic, Alexandre François Christe, Jin Wang, Mauro Carpita

This paper introduces a special session on results of the Swiss competence center on energy research FURIES that has been established in coordination with the Swiss Energy strategy 2050 with the specific aim to develop, promote and deploy power grid-relate ...

2019

Vacuum circuit breaker modelling for the assessment of transient recovery voltages: Application to various network configurations

Mario Paolone, Carlo Alberto Nucci

Vacuum circuit breakers (VCBs) are widely used for medium voltage applications when low maintenance, long operating life, and large number of allowable switching cycles are required. The accurate estimation of the transient recovery voltages (TRVs) associa ...

Elsevier2018

Implantable electrode and method for manufacturing

Diego Ghezzi, Marta Jole Ildelfonsa Airaghi Leccardi

The invention relates to a method for manufacturing an electrode, preferably an implantable electrode array comprising the following steps: Applying (101) a layer of electrically conducting material (4) above a substrate material (1) for forming the electr ...

2018