Publications associées à Moulage par projection simultanée

A model for the consolidation of hybrid textiles considering air entrapment, dissolution and diffusion

Véronique Michaud, Vincent Werlen, Christian Rytka

A new model is proposed for the consolidation of hybrid textiles, in which air entrapment and dissolution are considered. One of the key parameters is tow permeability, which is described by the analytical model of Gebart and validated at very high fibre v ...

ELSEVIER SCI LTD2023

Visualization and modelling of dynamic flow in fibrous preforms for liquid composite molding

Helena Luisa Teixido Pedarros

Nowadays, Liquid Composite Molding techniques are often used to manufacture high quality fiber reinforced composite parts at a relatively low cost. These involve an infiltration process, in which a liquid resin is forced to ingress into a dry fibrous porou ...

EPFL2023

Strategies for energy-efficient frontal polymerisation processing and microstructural evaluation of fibre reinforced composites

Jacobus Gerardus Rudolph Staal

Liquid composite moulding methods are widely applied for manufacturing of fibre reinforced polymer (FRP) composites and consist of two main stages: impregnation of fibrous reinforcements by a liquid monomer resin and curing of this resin. This thesis work ...

EPFL2023

Kinematic and mechanical response of dry woven fabrics in through-thickness compression: Virtual fiber modeling with mesh overlay technique and experimental validation

Véronique Michaud, Baris Çaglar, Lode Geeraard Daelemans

The through-thickness compressive behavior of fabric reinforcements is crucial in liquid composite molding manufacturing processes. Predictive simulations of the compressive response are thus necessary to enable a virtual processing workflow. These are com ...

2021

Out-of-plane permeability measurement for reinforcement textiles: A benchmark exercise

Véronique Michaud, Baris Çaglar, Amaël Maximilien Cohades, Damiano Salvatori

The out-of-plane permeability of two glass fibre fabrics was measured by 26 institutions using silicone oil as a test fluid. Participants in this study were free to select the test procedure, specimen dimensions and data analysis method, provided that test ...

2021

Optimization of multi-directional fiber architecture for resistance and ductility of bolted FRP profile joints

Thomas Keller, Lulu Liu, Xin Wang

In view of the low structural efficiency of bolted joints in pultruded fiber-reinforced polymer (FRP) profiles with mainly unidirectional (UD) fiber architecture, off-axis plies were considered as an effective way to improve bolted joint performance. An ex ...

ELSEVIER SCI LTD2020

Assessment of capillary phenomena in liquid composite molding

Véronique Michaud, Baris Çaglar, Feyza Karasu Kiliç, Cem Tekin

The interplay between capillary and viscous forces plays a significant role for optimal part quality in fiber-reinforced composites manufactured by Liquid Composite Molding (LCM); these are however difficult to analyze during flow. Two approaches are propo ...

2019

Influence of the stacking sequence on the low-energy impact resistance of flax/PA11 composite

Yann Albert Gérard Lebaupin

In this paper, the low-energy impact behavior of a fully biobased composite made of bio-sourced polyamide 11 resin reinforced with flax fibers was investigated. Different composite laminates were studied in order to determine the stacking sequence effects ...

SAGE PUBLICATIONS LTD2019

Numerically-based method for fracture characterization of Mode I-dominated two-dimensional delamination in FRP laminates

Thomas Keller, Anastasios Vassilopoulos, Aida Cameselle Molares

A new numerically-based method suitable for determining the total strain energy release rate (SERA) involved in two-dimensional (2D) Mode I-dominated delamination under opening loads in FRP laminates is presented. The method is based on the mutual dependen ...

2019

Size limitations on achieving tough and healable fibre reinforced composites through the use of thermoplastic nanofibres

Véronique Michaud, Amaël Maximilien Cohades, Lode Geeraard Daelemans

Phase-separated blends of epoxy and poly(ε-caprolactone) (PCL) provide crack repair in composites after a thermal treatment at 150 °C, but decrease the material’s fracture toughness. This article investigates the combination of healing with interlaminar fr ...

2018